Nissan Note — a compact and reliable car, but even it has problems with electrical problems over time. One of the most common problems is the failure of the wipers. Most often, the culprit is a burnt-out fuse, which protects the wiper circuit from overload. If your wipers suddenly stop working, do not rush to go to service: in 80% of cases the problem is solved by replacing the fuse in 5 minutes.

In this article you will find exact fuse location diagrams for Nissan Note first (E11, 2004–2012) and second (E12, 2012–2020) generations, step-by-step instructions for diagnosis and replacement, as well as answers to frequently asked questions. We will also look at why the wiper fuses blow and how to avoid repeated breakdowns.

Where is the windshield wiper fuse located? Nissan Note?

B Nissan Note The windshield wiper fuse is located in fuse box (aka fuse box). Its location depends on the generation of the car:

  • 🔧 E11 (2004–2012): fuse box is located to the left of the steering column, under a plastic cover. To gain access, pull the cover towards you - it is secured with latches.
  • 🔧 E12 (2012–2020): block moved into the interior, under the instrument panel on the driver's side. The cover is secured with two latches on the sides.

On the inside of the block cover there is usually a diagram indicating the fuses. If there is no diagram or it has been erased, use the data from the table below.

Generation Fuse number Denomination (A) Description
E11 (2004–2012) F30 10 Windshield wiper (windshield wipers)
E11 (restyling 2008–2012) F28 10 Wipers + washer
E12 (2012–2020) F17 15 Wiper and relay
E12 (since 2016) F19 10 Wipers only (no washer)

Important: On Nissan Note E12 after 2018, the wiper fuse can be duplicated in an additional block under the hood (number F40, 10A). Check both units if replacement inside did not help.

📊 What Nissan Note do you have?
  • E11 (2004–2012)
  • E12 (2012–2020)
  • I don't know the generation
  • Another Nissan

How to check the wiper fuse?

Before replacing the fuse, make sure that this is the problem. Here step-by-step diagnostics:

  1. Turn on the ignition (it is not necessary to start the engine).
  2. Activate the wipers switch on the steering lever. If they don't move, proceed to check.
  3. Remove the fuse tweezers (usually included in the block) or pliers. Pay attention to its condition:
    • ✅ Whole: The metal thread inside is not damaged.
    • ❌ Burnt out: The thread is broken or melted.
  4. Check with a multimeter (if any):
    • 🔋 Set circuit test mode (diode or resistance icon).
    • 🔌 Touch the fuse contacts with the probes. If resistance 0 ohm - he is correct. If OL (break) - burned out.

If the fuse is good, but the wipers do not work, the problem may be wiper relay (usually R12 on E11 And R15 on E12) or in the wiper motor itself.

💡

Do not test the fuse for a spark - this may damage the vehicle's electronics. Use visual inspection or multimeter only.

Step-by-step replacement of the wiper fuse

If the fuse is blown, replace it with a new one same denomination. Using a high amperage fuse may result in fire in the wiring!

☑️ What you will need to replace

Done: 0 / 4

Instructions:

  1. Turn off the ignition and remove the key. This will prevent short circuit.
  2. Remove the fuse box cover (see section above).
  3. Find the right fuse by number from the table. There may be a diagram with symbols on the block cover.
  4. Remove the blown fuse tweezers. If you don't have tweezers, carefully pry them off with a thin-blade screwdriver.
  5. Install a new fuse the same denomination. Do not insert bugs (wires) - this is dangerous!
  6. Check the operation of the wipersby turning on the ignition and activating the windshield wipers.

If the fuse blows again after replacement, this indicates short circuit in the chain. In this case, diagnostics of the wiring or wiper motor is required.

💡

Never use fuses with a rating higher than that shown in the table. For example, instead of 10A you cannot use 15A - this could burn the wiring!

Why do the wiper fuses blow?

A blown fuse is symptom, not the reason. If replacement does not help for a long time, look for the root of the problem:

  • ⚡ Short circuit in wiring. Often occurs due to frayed wires (for example, in the corrugation between the body and the door) or oxidized contacts.
  • 💦 Freezing or clogged wiper motor. If the mechanism is jammed, it draws more current and the fuse blows.
  • 🔧 Faulty relay. Wiper relay (R12/R15) can “stick”, causing overload.
  • 🌧️ Water entering the fuse box. This leads to corrosion and short circuits. A common problem after pressure washing.

To prevent repeated breakdowns:

  • 🔍 Inspect regularly corrugated wiring between the body and the door - wires often fray there.
  • ❄️ In winter before parking turn off the wipersso that they do not freeze to the glass.
  • 🚿 Avoid high pressure washing in the area fuse box and wiper motor.
How to check the wiper motor for jamming?

Disconnect the motor connector (located under the plastic protection at the base of the wipers). Check if the motor shaft rotates manually. If not, the mechanism is jammed and requires repair or replacement.

What to do if replacing the fuse did not help?

If the wipers still do not work after replacing the fuse, check:

  1. Wiper relay:
    • On E11 this is a relay R12 (in the main block).
    • On E12 — R15 (same place as the fuse).

    Try swapping it with a similar relay (for example, with a horn relay); if the wipers work, the relay is faulty.

  2. Wiper gear motor:
    • Remove the plastic protection under the wipers.
    • Disconnect the motor connector and check the voltage on the wires when the wipers are turned on (there should be 12V).
    • If there is voltage, but the motor does not work, it is burned out.
  • Wiper switch:

    The contacts under the steering wheel may oxidize. Try moving the lever - if the wipers sometimes work, the problem is in the switch.

    • ⚠️ Attention: If you hear the relay click when you turn on the wipers, but the motor does not rotate, do not keep the lever on for more than 5 seconds. This may burn the motor winding.

    Cost of repairs and where to buy spare parts

    Prices for fuses and related parts for Nissan Note:

    Detail Article (example) Cost (RUB) Where to buy
    Fuse 10A — 20–50 Any auto shop
    Fuse 15A — 30–60 Auto parts, Ozon, Wildberries
    Wiper relay 28520-4M000 (original) 800–1500 Nissan dealer, Exist.ru
    Wiper gear motor 28550-4M000 (E11), 28550-JM00A (E12) 4000–8000 Autoanalysis, Exist.ru

    If you are not confident in your abilities, service repairs will cost:

    • 🔧 Replacing the fuse/relay: 300–800 rub.
    • 🔧 Electrical diagnostics: 1000–2000 rub.
    • 🔧 Replacement of gear motor: 2500–4000 rub. (with spare part - up to 10,000 rub.).

    To save money you can order non-original spare parts (for example, a wiper motor from Febi or Valeo), but ensure catalog compatibility.

    FAQ: Frequently asked questions about the wiper fuse Nissan Note

    Is it possible to drive without a wiper fuse?

    No! Without a fuse, the wiper circuit is not protected from overloads. This may lead to fire in the wiring or failure of the windshield wiper motor. Always install a fuse with the rating specified in the manual.

    Why does the fuse burn out immediately after replacement?

    This indicates short circuit in the chain. Common reasons:

    • Damaged wire insulation (especially in the corrugation between the body and the door).
    • Jammed wiper motor.
    • Faulty relay.

    Diagnostics with a multimeter or at a car service is required.

    Which fuse should I install if there is no circuit in the block?

    For Nissan Note E11 (2004–2012) this is usual F30 (10A) or F28 (10A). For E12 (2012–2020) — F17 (15A) or F19 (10A). If you are not sure, use a multimeter in test mode: with the wipers on, check which fuse has voltage.

    Is it possible to repair the wiper motor yourself?

    Sometimes. If the problem is jammed brushes or oxidized contacts, the motor can be disassembled, cleaned and lubricated. But if the winding is burned out or the gears are worn out, replacement will be required. Disassembly requires screwdrivers and patience - there are many small parts inside.

    Where to download the wiring diagram Nissan Note to check the circuit?

    Official diagrams can be found:

    • B repair manual (For example, Haynes or Autodata).
    • On the forums: NoteClub, Nissan-Club.
    • In the program Mitchell1 or AllData (paid).

    For E11 And E12 The schemes are different - make sure you download the correct version.