Removing the standard radio Nissan Qashqai J10 (2007–2013) is a task that owners face when upgrading an audio system, repairing or diagnosing electronics. At first glance, the procedure seems simple, but without knowledge hidden fastenings, wiring features and sequence of actions, you may encounter broken clips, broken connectors, or even airbag deployment (if we are talking about models with an integrated control unit).
In this article we will analyze three official ways to remove the radio (depending on the vehicle configuration), we will list the necessary tools and show you unique tricks to bypass problems with latches and warn you against common mistakes. We will also answer questions about compatibility with after-market systems and preservation of steering functions.
What radios were installed on the Qashqai J10?
On Nissan Qashqai J10 Depending on the year of manufacture and configuration, three types of head units were installed:
- 🔹 Basic version — Nissan CD/RDS (no display, only buttons). Markings on the body:
28210-4M00Aor28210-4M01A. - 🔹 Average equipment — Nissan Audio 6CD with monochrome screen (supports
MP3/CD). Article:28210-4M02A. - 🔹 Top version — Nissan Connect with color display and navigation (item:
28210-4M10A). Found in Tekna And Acenta Premium.
Important: radios in Qashqai J10 are attached to four plastic latches (two on each side), but in versions with Nissan Connect Additionally, a metal frame is used, screwed to the dashboard. This complicates dismantling - without special keys or a screwdriver with a thin blade, you can damage the panel.
- Basic (no screen)
- With monochrome display
- Nissan Connect (color screen)
- I don't know
Tools for removing the radio: what will you need?
To remove the standard radio Nissan Qashqai J10 you will need:
- 🔧 Plastic mounting blades (2–3 pcs.) - for snapping off clips without scratches.
- 🔧 Torque screwdriver with nozzle
T20(for frame Nissan Connect). - 🔧 Keys for removing the radio (if not, a pair of forks or homemade wire hooks will do).
- 🔧 Multimeter — to check the voltage on the connectors (optional, but recommended).
- 🔧 Duct tape or marker — to mark the connectors when disconnecting.
⚠️ Attention: If your car has a radio with integrated climate control unit (found in Tekna 2010–2013), for dismantling you will need to remove the entire center console. In this case, add to the list 10 mm socket wrench for unscrewing the console fasteners.
Before starting work, disconnect the negative terminal of the battery for 10–15 minutes. This will relieve residual voltage in the system and prevent short circuits if the wires accidentally touch.
Step-by-step instructions: removing the Qashqai J10 radio
The dismantling process differs depending on the type of radio. Below are universal instructions taking into account the nuances for each version.
Step 1: Preparing the interior
1. Turn off the ignition and remove the key from the castle.
2. Open the glove compartment and find fuse F37 (10A) in the fuse box (it is responsible for the audio system). Remove it to disconnect power from the radio.
3. If the car has backlighting for the radio buttons, wait until it goes out (this is a signal that the capacitors are discharged).
Step 2: Removing the Decorative Frame
1. Take a plastic spatula and carefully pry up the radio frame from below (from the glove compartment). Press with a force of 1–1.5 kg - the two lower clips should click.
2. Repeat the action from above, then pull the frame towards you. In versions with Nissan Connect the frame is additionally secured with two screws T20 — they need to be unscrewed in advance.
What to do if the frame cannot be removed?
If the frame does not budge, check whether the climate control unit is preventing its removal. In some configurations, the radio frame is connected to the climate control panel - in this case you will have to remove the entire console.
Step 3: Removing the radio
1. Paste keys for removing radio (or homemade hooks) into the side grooves until they stop. If you don't have keys, use two forks, wrapping the ends with electrical tape to prevent scratching the panel.
2. Pull the keys evenly outward — the radio tape recorder should come out of the seat by 2-3 cm. Then you can grab it with your hands and carefully pull it out.
3. Disconnect the connectors:
- ISO connector (power supply and speakers) - black plastic block.
- ANT connector (antenna) - round metal plug.
- CAN bus (only in Nissan Connect) - flat white connector.
☑️ Check before removing the radio
⚠️ Attention: In radios Nissan Connect connector CAN buses often sticks to the board. Do not pull on the wire - gently rock the connector left and right while pulling it out.
Step 4: Check Connectors and Wiring
After removing the radio, inspect the connectors for oxidation or damage. If you plan to install a new radio, compare the pinout of the connectors:
| Connector | Wire color | Purpose | Note |
|---|---|---|---|
| ISO (A) | Yellow | +12V constant | Connected to battery |
| ISO (B) | Red | +12V when ignition is turned on | Often used to control an amplifier |
| ISO (C) | Black | Ground (GND) | Check the reliability of the fastening |
| ANT | — | Antenna signal | B Tekna could be an antenna amplifier |
| CAN | Green/white | Data bus | Only in Nissan Connect |
Typical problems and how to avoid them
When removing the radio in Qashqai J10 Owners most often encounter the following difficulties:
- 🔌 Broken CAN bus wires — occurs when the connector is suddenly pulled out. Consequences: errors on the dashboard, non-functional buttons on the steering wheel.
- 🔧 Broken plastic latches — if you pull the radio without keys. Solution: use spatulas on both sides.
- 📻 Antenna signal loss - if you don’t mark the connector
ANT. B Tekna the antenna can be connected via an amplifier. - ⚡ Short circuit - if you don't turn off the fuse
F37or battery terminal.
💡 Lifehack: If after installing a new radio the buttons on the steering wheel stop working, check the connection CAN buses. In most cases, the problem is solved by purchasing CAN-Bus adapter (For example, Connects2 CTNI23 for Nissan).
If, after removing the radio, an error appears on the dashboard Audio Error, reset it through the on-board computer menu: Settings → System → Reset Audio.
Installing a new radio: what you need to know?
When replacing the standard radio with an aftermarket system (for example, Pioneer, Alpine or Android-auto) consider:
- Seat size - in Qashqai J10 standard is used
2DIN(height 100 mm). Most modern radios are suitable, but may be required transitional framework. - CAN bus compatible — without the adapter, the buttons on the steering wheel and the display of tracks on the on-board computer display will not work.
- Antenna - used in some configurations active antenna with amplifier. If the new radio does not support 12V on the antenna connector, you will have to buy more passive adapter.
- Connecting a rear view camera - in Tekna The camera is integrated into the radio. To save it you will need video adapter (For example, Nissan RCA Adapter).
📌 Recommendation: Before purchasing a new radio, check its compatibility with Nissan Qashqai J10 on the manufacturer's website. For example, at Pioneer There is a special filter by car make and model.
Frequently asked questions about removing the Qashqai J10 radio
Is it possible to remove the radio without keys?
Yes, but the risk of damaging the panel or latches increases. Alternative ways:
- Use two dinner forks, wrapping the ends with electrical tape.
- Cut keys from plastic card or an aluminum can.
- Apply thin screwdriver, but act extremely carefully so as not to scratch the panel.
⚠️ Attention: In radios Nissan Connect You can’t do without keys - they use metal latches that cannot be snapped off with a spatula.
Why does the climate control not work after removing the radio?
In complete sets Tekna And Acenta Premium The climate control unit is integrated with the radio via CAN bus. If the connection is lost, the system goes into emergency mode. Solutions:
- Check your connection
CAN buses(white connector). - Reset the error through the on-board computer menu:
Settings → Climate → Reset. - If the problem persists, contact an electrician to diagnose the unit. BCM.
How to connect a new radio to the standard antenna?
B Qashqai J10 standard is used ISO connector for an antenna, but there are some nuances:
- If the antenna active (with amplifier), the new radio will require 12V at the antenna connector. Check this in the device instructions.
- To connect Android-auto a cassette player may be needed FM modulator (if there is no built-in radio receiver).
- In versions with Nissan Connect The antenna cable sometimes goes through the amplifier in the trunk - it needs to be bypassed or replaced.
What should I do if the speakers do not work after installing a new radio?
Causes and solutions:
| Problem | Diagnostics | Solution |
|---|---|---|
| Incorrect pinout | Test the wires with a multimeter | Reconnect the connectors according to the diagram |
| Broken wire | Visual inspection, continuity test | Solder or replace the harness |
| Incompatible with amplifier | Checking the voltage on the amplifier wires | Install an adapter or bypass the amplifier |
Is it possible to return the stock radio after removal?
Yes, but keep in mind:
- If they were broken during dismantling plastic latches, the radio will wobble. The solution is to install new clips (part number:
28215-4M000). - When disconnected
CAN busesThe climate control and clock settings may be reset. - If the battery has been disconnected for a long time, the radio may require input unlock code (indicated in the service book).