Removing the rear seat on a Nissan Almera G15: instructions with photos and tips

Rear seat in Nissan Almera G15 (2013-2018) may require removal to clean the interior, repair electronics, replace trim, or access the fuel pump. Unlike previous generations Almera Classic, model G15 has a specific fastening design, which often raises questions among owners. An incorrect approach to removing a sofa can lead to broken plastic latches or damage to the upholstery, so it is important to know the exact sequence of actions.

In this article you will find step-by-step instructions with photos, a list of necessary tools, as well as unique nuances for Almera G15, which are not in the general instructions for disassembling the interior. We'll figure out how to avoid common mistakes, such as damage to the heated seat wiring (if installed) or deformation of the metal frame. And at the end - answers to frequently asked questions and tips on reassembly.

Preparing for dismantling: tools and safety precautions

Before you begin removing the rear seat, prepare your workspace and tools. B Nissan Almera G15 the sofa is attached to the body using four bolts (two on each side) and two plastic latches on the front. You don't need complicated equipment, but there are a few things that will make the process easier:

• 🔧 Tools: socket wrench or socket 10 mm, a flat-head screwdriver (for prying up plastic clips), a flashlight for illuminating the fasteners under the seat.
• 🧹 Cleanliness: Vacuum the interior so that dirt does not get into the fastening mechanisms or heating contacts (if any).
• 🔌 Electrical: if your Almera G15 equipped with heated rear seats, Be sure to disconnect the negative terminal of the battery 10 minutes before starting work to avoid short circuit.
• 📸 Documentation: Take a photo of the location of the bolts and wiring before dismantling - this will help with reassembly.

Pay special attention to the plastic latches on the front of the sofa. B Almera G15 they often break when removed carelessly, and the original parts cost 800–1200 ₽ per piece. If the clips are already damaged, buy analogues in advance (for example, art. 77010-4M000 for front mounts).

⚠️ Attention: Do not use excessive force when lifting the seat - there are heating wires running through the back of the sofa (if installed) that can be accidentally torn off. If you feel resistance, check that all bolts are unscrewed.

Step-by-step instructions: how to remove the rear sofa

The process of removing the rear seat Nissan Almera G15 takes 15–20 minutes if you have experience. Follow the instructions strictly in order to avoid damage:

1. Unscrew the rear mounting bolts. They are located under plastic plugs at the bottom of the sofa (two on each side). Use the head on 10 mm:

   1. Подденьте заглушки плоской отвёрткой.
   2. Открутите болты против часовой стрелки.
   3. Придерживайте сиденье рукой, чтобы оно не упало после снятия последнего болта.

2. Release the front latches. Lift the sofa up and pull it towards you - it is held in front by two plastic clips. If the seat does not give way, check whether the seat belts are caught on the metal frame.

3. Disconnect the wiring (if there is heating). Under the sofa you will see a connector with wires. Carefully release it by pressing the latch. Don't pull the wires!

After removal, inspect the fasteners for corrosion or damage. B Almera G15 bolts often rust due to moisture entering through door seals. If the threads are damaged, replace the bolts with new ones (art. 08915-6040A).

Check battery disconnection (if heated)

Prepare tools (10 mm socket, screwdriver)

Take photos of the location of the bolts and wiring.

Make sure that the seat belts do not interfere with dismantling-->

Nuances for different configurations of Almera G15

Rear seat design Nissan Almera G15 may vary depending on configuration. Here are the key features to consider:

Equipment	Mounting features	Additional actions
Base	4 bolts + 2 plastic latches	Check the integrity of the seals under the seat - they often wear out
Comfort	Additional armrest mounting bolts	Remove the armrest before dismantling the sofa (2 bolts on 10 mm)
Tekna (heated)	Wiring under the seat, connector under the central tunnel	Disconnect the battery in advance, check the integrity of the wires after removal

In versions with heated rear seats (optional H11 in the VIN code) wires are laid under the sofa to the heating elements. They are easy to damage if removed carelessly, therefore:

• 🔌 Disconnect the battery after 10–15 minutes before work
• 📏 Check the location of the wires before lifting the seat - they may be attached to the frame with plastic ties.
• 🔧 Use a plastic tool to disconnect the connector to avoid damaging the contacts.

⚠️ Attention: Complete with system NissanConnect (Multimedia with Navigation) There may be an antenna cable running under the rear seat. Do not pull the seat sharply back - you risk tearing off the connector!

What to do if the bolt is rusty?

If the bolt does not unscrew, do not use excessive force - you risk stripping the thread. Treat it with a penetrating lubricant (eg WD-40) and wait 5–10 minutes. If this doesn't work, use an impact wrench or drill out the bolt, then tap new threads M6.

Common mistakes and how to avoid them

Even experienced car owners make mistakes when removing the rear seat Nissan Almera G15. Here are the most common ones and ways to prevent them:

• 🔧 Broken threads of bolts. The reason is the use of an inappropriate tool (for example, an open-end wrench instead of a socket). Always use 10 mm socket wrench with extension for access to rear bolts.
• 💥 Broken plastic latches. Do not pull the seat up if it does not give in - first check that all the bolts are unscrewed. The clips can be lubricated with silicone grease to make removal easier.
• ⚡ Heating wiring short circuit. If you forget to disconnect the battery, disconnecting the connector may blow the fuse F37 (15A) in the block under the hood.
• 🔩 Lost bolts or plugs. Use a magnetic tray for fasteners or stick them with tape to the body so as not to lose them.

Another common problem is seat misalignment during reinstallation. This happens if the bolts are not tightened evenly. To avoid squeaks and backlash:

1. Tighten the bolts criss-cross (first two diagonal ones, then the remaining ones).
2. Check that the rubber seals under the bolts are in place - they prevent moisture from entering.

Cleaning and repairs after removing the seat

When the back sofa Nissan Almera G15 removed, you have access to hidden areas of the cabin that are rarely cleaned. Here's what to do:

• 🧽 Carpet cleaning. Dust, sand and moisture accumulate under the seat. Use a vacuum cleaner with a narrow attachment and an interior cleaner (such as Profoam 2000).
• 🔧 Checking the fuel pump. B Almera G15 The fuel pump hatch is located under the rear seat (on the right). Inspect the O-ring for cracks—its wear can cause a gasoline smell in the cabin.
• 🔌 Wiring diagnostics. Check the integrity of the heating wires (if any) and connectors. Oxidized contacts can be cleaned with an eraser or a special liquid. Contact Cleaner.
• 🛠️ Frame repair. If the metal parts of the seat are rusty, treat them with a rust converter (for example, Tsinkar) and paint.

If you removed the seat for replacing the casing, please note that in Almera G15 covers are attached to the frame using:

• Plastic clips (on the sides).
• Velcro (on the back).
• Metal staples (below) - to remove them you will need anti-staple stapler.

⚠️ Attention: When replacing the trim, do not use sharp objects to remove old staples - this may puncture the foam filling. It is better to cut them with side cutters.

Reassembly: how to install the seat correctly

Installing the rear sofa in Nissan Almera G15 It seems simple, but there are some nuances here. Follow this sequence to avoid squeaks and play:

1. Check the condition of the fasteners. Make sure all bolts and clips are intact. If the plastic latches are broken, replace them (art. 77010-4M000).

2. Reinstall the seat. Start at the rear and line up the bolt holes with the body mounts. Then lower the front until the latches click into place.

3. Tighten the bolts. Use a torque wrench 20–25 Nm. Tighten in a cross pattern to avoid distortion.

4. Connect the wiring (if there is heating). Make sure that the connector is latched all the way - you should hear a characteristic click.

5. Check systems operation. Connect the battery and check:

   • Heating operation (if any).
   • No errors on the dashboard (eg Check Seat Belt).
   • No squeaks when the seat rocks.

If extraneous sounds appear after installation, the reasons may be as follows:

Problem	Reason	Solution
Creak when moving	Insufficient bolt tightening	Tighten the bolts to a torque 25 Nm
Seat play	Broken plastic latch	Replace the clip (art. 77010-4M000)
Burning smell	Short circuit in heating wires	Check the fuse F37 (15A) and wiring integrity

FAQ: Frequently asked questions about removing the rear seat

Is it possible to remove the rear seat in Almera G15 without tools?

No, you will definitely need a socket wrench or socket 10 mm for unscrewing bolts. The plastic latches on the front can be released manually, but the seat cannot be completely removed without a tool.

How many bolts secure the rear seat in Almera G15?

In the basic configuration - 4 bolts (two on each side). Heated or armrest versions may have additional attachments.

What should I do if, after removing the seat, the smell of gasoline appears in the cabin?

Most likely, the fuel pump seal is damaged (the hatch is located under the right side of the sofa). Replace the O-ring (art. 17342-JK00A) and check the integrity of the hoses.

How to remove the trim from the rear seat of Almera G15?

The casing is attached with plastic clips, Velcro and metal brackets. To remove:

1. Carefully pry up the clips on the sides of the seat.
2. Peel off the Velcro on the back.
3. Cut the staples from the bottom using side cutters (do not use a knife!).

For reassembly, use new brackets (art. 08903-1R000).

Where can I buy original clips for fastening the seat?

Original plastic latches can be ordered by art. 77010-4M000 from official dealers Nissan or in online stores (for example, Exist.ru, Autodoc). Cost - from 200 ₽ per piece. Analogues: Febi 15310 or Hella 8XH 355 349-121.