Nissan Almera Classic - one of the most popular foreign cars on the secondary market in Russia and the CIS countries. Despite its modest dimensions, the windshield of this model requires special attention: not only the appearance, but also driving safety depends on the accuracy of the dimensions. In this article we will analyze the official parameters of glass for all generations Almera Classic (including B10, N16 And G15), nuances of selecting analogues and typical mistakes when replacing.
Why is it so important to know the exact dimensions? It's not just a matter of aesthetics: incorrectly selected glass can disrupt the operation of the rain sensors, reduce visibility or even lead to cracks due to mismatched curvature. We collected data from official catalogs Nissan, plus reviews from auto glass technicians to help you avoid costly mistakes.
Official windshield dimensions for Nissan Almera Classic by generation
Windshield sizes vary depending on the year of manufacture and body modification. Below is the data for the most common versions:
| Generation/Model | Years of manufacture | Glass size (W×H), mm | Original code (OEM) | Notes |
|---|---|---|---|---|
| Almera Classic B10 (sedan) | 1995–2000 | 1350×750 | 28510-4M000 | Without rain sensor, thin glass (4.5 mm) |
| Almera N16 (hatchback/sedan) | 2000–2006 | 1380×780 | 28510-4M600 | With heating zone, tinted top edge possible |
| Almera Classic G15 (restyling) | 2006–2012 | 1400×800 | 28510-4M610 | Thickened glass (5.2 mm), compatible with light/rain sensor |
| Almera Classic (for the Russian market, 2013–2018) | 2013–2018 | 1420×820 | 28510-4M620 | Athermal coated, reinforced edge |
⚠️ Attention: Dimensions may vary slightly (within ±5 mm) due to manufacturing conditions. Always check with VIN code car when ordering glass!
For an accurate selection, use auto glass catalogs (For example, Hella Gutmann or Sekurit), where not only the dimensions are indicated, but also radius of curvature, thickness and availability of additional options (heating, tinting).
- Original (Nissan)
- Analogue (Pilkington, Sekurit)
- Chinese unoriginal
- I don't know
How to measure your windshield yourself: step-by-step instructions
If you are not sure about the model of your car or suspect that the previous owner installed non-original glass, you can take measurements yourself. You will need:
- 📏 Tape measure or ruler (preferably metal)
- 📝 Notepad for notes
- 🔦 Flashlight (for inspecting the edge)
- 🧲 Magnet (to check the presence of a metallized strip)
Measurement algorithm:
- Measure glass width along the top edge (from edge to edge of the seal).
- Measure height from the bottom edge to the top point (usually in the center).
- Check radius of curvature: Apply a ruler to the glass - if the gap is more than 2mm, the curvature is not suitable.
- Inspect the edge for heating filaments or sensors.
Dimensions (W×H) match the catalog
Presence/absence of a rain sensor
Glass thickness (4.5 mm or 5.2 mm)
Edge type (with or without seal groove)
Heating compatibility (if available)
-->
⚠️ Attention: If there is any on the glass crack more than 10 cm long, measurements may be inaccurate due to deformation. In this case, it is better to remove the glass and measure it on a flat surface.
Original vs analogues: what to choose for Nissan Almera Classic?
Original glass from Nissan guarantee 100% compatibility, but their price often exceeds 15–20 thousand rubles. Alternative options:
- 🔹 Pilkington (UK) - best price/quality ratio, full compatibility with sensors.
- 🔹 Sekurit (France) - premium segment, athermal coating as standard.
- 🔹 XYG (China) - a budget option, but there are often problems with curvature.
- 🔹 NordGlass (Russia) - optimal for regions with cold climates (reinforced edge).
Key differences between the original and its analogues:
| Parameter | Original (Nissan) | Pilkington/Sekurit | Chinese analogues |
|---|---|---|---|
| Thickness, mm | 5.2 (G15) / 4.5 (B10) | 5.2 (standard) | 4.8–5.0 (may vary) |
| Athermal coating | Yes (since 2013) | Yes | More often than not |
| Sensor compatibility | 100% | 99% | 50–70% |
When purchasing an analogue, be sure to check with the seller whether the glass is certified according to the standard ECE R43. Without this certificate, the glass may not withstand the impact of an accident.
Common mistakes when replacing a windshield and how to avoid them
Even experienced craftsmen sometimes make mistakes that lead to leaks, creaks or glue peeling off. The most common problems:
- Wrong glue. For Almera Classic suitable only polyurethane glue (For example, SikaTack or 3M PU590). Epoxy glue does not provide the required elasticity.
- Failure to comply with temperature conditions. The glue sets at +20°C. If the garage is colder, use infrared lamp.
- Poor edge cleaning. Remains of old glue or rust lead to peeling. Treat the surface
anti-corrosion primer. - Incorrect alignment. The glass should be installed with a gap of 2–3 mm around the perimeter to compensate for expansion.
⚠️ Attention: If after replacement there is whistling at speeds above 90 km/hMost likely, the glass is installed skewed. This is dangerous: in a strong wind it can burst!
What to do if the glass cracks immediately after installation?
If a crack appears within 24 hours, either the faulty glass or a violation of the installation technology is to blame. Required:
1. Take a photo of the defect and glass packaging (for warranty).
2. Check if there are any metal burrs left on the edge.
3. Contact a workshop - by law they are required to redo the work for free.
How to save on replacement: repair vs replacement
Not every crack requires a complete glass replacement. That's when you can get by repairs:
- 🔧 Chip up to 2 cm in diameter - filled with polymer (cost ~1500 rubles).
- 🔧 Crack up to 10 cm, which does not extend to the edge of the glass, is repaired using an injector.
- 🔧 Scratches (no deeper than 0.5 mm) - polished with a special paste.
❌ When repairs are futile:
- 🚫 The crack has touched glass edge (risk of spread).
- 🚫 Damage to driver's viewing area (distorts visibility).
- 🚫 Multiple chips (more than 3 pieces in an area of 20×20 cm).
Glass repair is 3–5 times cheaper than replacement, but only if the damage is not critical. For cracks longer than 15 cm or in the sensor area, repair will not help.
Where to buy glass for Nissan Almera Classic: verified suppliers
Prices for windshields for Almera Classic vary from 3,000 to 25,000 rubles depending on the type and manufacturer. Where to look:
- 🛒 Official Nissan dealers — original, but expensive (from 18,000 rubles).
- 🛒 Specialized auto glass stores (For example, Avtosteklo.ru, GlassService) - a wide selection of analogues.
- 🛒 Marketplace (Avito, Drom, Yula) - you can find a used original for 5,000–8,000 rubles, but there is a risk of running into defects.
- 🛒 Aliexpress - cheap Chinese glass (from 3,000 rubles), but the quality is unpredictable.
🔍 How to check the seller:
- Request photo of packaging with article number.
- Check if there is installation warranty (minimum 1 year).
- Check workshop reviews on 2GIS or Yandex.Maps.
⚠️ Attention: On Almera Classic G15 (2013–2018) glasses with athermal coating are often counterfeited. The original has green tint and labeling DOT-43 in the corner.
FAQ: Frequently asked questions about windshields Nissan Almera Classic
Can I install glass from another Nissan model?
Theoretically on Almera Classic N16 suitable glass from Nissan Primera P12 (dimensions 1380x780 mm), but there may be problems with attaching the wipers and rain sensor. For G15 There are no analogues - only the original or certified substitutes.
How long does it take to replace glass?
In the service, the procedure takes 2–3 hours (including drying of the glue). Self-replacement can take 5-6 hours due to the need to carefully remove the old glass and clean the edge.
Is it possible to drive with a cracked glass?
According to traffic regulations (clause 4.3), operation is prohibited if the crack impairs the driver's visibility or has sharp edges. Fine - 500 rubles. (Article 12.5 of the Administrative Code). Even if there is no fine, the risk that the glass will shatter when hitting a bump is very high.
How to care for new glass?
For the first 24 hours after replacement, you should not wash the car or drive at speeds above 80 km/h. In the future:
- Use contactless car wash (the brushes scratch the glass).
- Apply hydrophobic coating (For example, Rain-X) once every 3 months.
- Avoid sudden temperature changes (for example, do not pour hot water on frozen glass).
What to do if a squeak appears after replacement?
The creaking occurs due to:
- Poorly cleaned edge (needs to be re-glued).
- Poor quality seal (replace with original
28520-4M600). - Glass distortion (adjustable with wedges during installation).
If the squeaking does not go away after a week, contact service - this is a warranty case.