Replacing the standard radio with Nissan Qashqai J10 (2007-2013) is a challenge many owners face when upgrading their audio system. However, without precise pinout of connectors, the risk of connection errors increases: from loss of functionality to short circuit. In this article we will look at all pinout options - both for original audio and for adapters for ISO-connectors, and also tell you how to avoid typical problems when installing a new radio.

Feature Qashqai J10 — use of non-standard connectors Nissan, which are not compatible with most universal head units. Here it is important to consider not only the colors of the wires, but also their functional purpose: power, speakers, antenna, steering wheel controls (if supported). We have collected current diagrams for all trim levels, including versions with Bose and without it.

Standard pinout of the Qashqai J10 head unit

Original radio in Qashqai J10 connects via two main connectors: A (power and speakers) and B (antenna, CAN bus, additional functions). Below is the pinout for the basic version without the system Bose:

Contact Wire color Purpose Notes
A1 Yellow +12V (constant) Memory power
A2 Red +12V (ignition) Activated when turning the key
A3 Black Ground (GND) General minus
A4 Green/black Antenna output Active Antenna Control
A5–A8 Grey, white, green, purple Speakers (front/rear) Polarity: solid color - "+", stripe - "-"

Important: in versions with Bose the circuit is different - amplifiers are used, and the speaker wires go directly to them, and not to the radio. More on this in the next section.

⚠️ Attention: Do not confuse the yellow (+12V constant) and red (+12V ignition) wires. Connecting them in the reverse order will lead to battery discharge or failure of the radio settings.

Pinout for version with Bose audio system

If your Qashqai J10 equipped with a system Bose, then the standard radio does not directly control the speakers - the signal goes to an external amplifier. In this case, the connector pinout A will be as follows:

  • 🔌 A1 (yellow) — +12V constant (same as the basic version).
  • 🔌 A2 (red) — +12V ignition.
  • 🔌 A3 (black) — mass.
  • 🔊 A4–A7 (paired wires) - amplifier outputs Bose (not on speakers!).
  • 📡 A8 (green/black) — antenna control.

Amplifier Bose in Qashqai J10 usually located under the front passenger seat or in the trunk. To connect a non-original radio, you will need amplifier walker (For example, DSP-interface), since the signal from the new head unit must be adapted to the inputs Bose.

📊 What kind of radio are you planning to install?
  • 1DIN
  • 2DIN
  • Android Auto
  • Apple CarPlay
  • Other

If you are not sure whether your car has a system Bose, check for branded speakers (usually marked Bose on the basket) or amplifier in the trunk. You can also see VIN-car code - option Bose indicated in the package as B92 or B93.

Adapters for connecting non-original radios

To install a universal radio (for example, Pioneer, Sony or JVC) in Qashqai J10 you will need an adapter that converts the standard connectors Nissan to standard ISO. The most popular options:

  • 🔌 Adapter Nissan 16-pin to ISO - for basic versions without Bose.
  • 🔌 Connects2 CTNI001 — supports maintaining control from the steering wheel.
  • 🔌 Axxess ASWC-1 — universal adapter for integration with steering wheel buttons.

When choosing an adapter, pay attention to the supported functions: CAN bus (to display information on the display), SW-CAN (steering wheel control), as well as the presence of an output to the standard amplifier (if there is one) Bose).

Check the availability of the Bose system|Check the number of contacts in the connector|Check compatibility with the radio model|Pay attention to CAN bus support-->

The cost of adapters varies from 1,500 to 5,000 rubles, depending on the functionality. For example, Connects2 CTNI001 will cost ~3,500 rubles, but will allow you to retain audio control from the steering wheel and integration with the on-board CAN bus.

Step-by-step instructions for connecting a new radio

Before starting work, turn off negative battery terminal - this will prevent a short circuit. Next, follow the algorithm:

  1. Removing the standard radio:

    Remove the decorative panel around the radio (usually secured with latches). Unscrew the 4 bolts in the corners and carefully pull out the device, disconnecting the connectors A And B.

  2. Adapter connection:

    Connect the standard connectors Nissan with adapter (eg CTNI001), then connect ISO- connectors for the new radio. Check the adapter pinout diagram!

  3. Power check:

    Connect the battery and check if the radio turns on. If not, double check yellow (+12V constant) And black (mass) wires.

  4. Speaker setup:

    In the menu of the new radio, select the mode 4CH (if 4 speakers are connected) and check the polarity. If the connection is incorrect, the sound will be “out of phase”.

⚠️ Attention: If after connecting the radio turns on, but there is no sound, check:
  • 🔊 Are the speaker wires connected to the correct outputs (FL, FR, RL, RR).
  • 🔌 Is the amplifier output mode configured in the radio (if there is one? Bose).
  • 📡 Is the antenna control activated (green/black wire).
💡

If after installing a new radio the steering buttons stop working, check the adapter connection ASWC-1 to CAN bus (usually orange and orange-black wires).

Common mistakes and how to avoid them

Even if the diagrams are followed exactly, owners Qashqai J10 often encounter problems. Here are the most common:

  • ⚡ Short circuit - occurs when the connection is incorrect red (+12V ignition) And yellow (+12V constant) wires Symptoms: The fuse trips F33 (10A) in the block under the hood.
  • 🔇 No sound - most often due to incorrect speaker polarity or unactivated amplifier output (for Bose).
  • 📻 Antenna doesn't work — check the green/black wire and the presence of power on it (+12V when the radio is turned on).
  • 🔄 Reset settings - occurs if the yellow wire (+12V constant) is not connected or it is in contact with ground.

Critical error: connecting the radio without an amplifier bypass in systems with Bose will lead to no sound or damage to the speakers! In this case, you either need to install DSP interface, or replacing the amplifier with a passive system.

If after connecting the radio does not turn on, check:

  1. Presence of voltage on the yellow and red wires (with a multimeter).
  2. Fuse integrity F33 (10A) in the fuse box under the hood.
  3. The ground connection is correct (the black wire must be securely fastened to the body).

Compatible with steering wheel buttons and CAN bus

To retain audio control from the steering wheel in Qashqai J10 requires an adapter that supports SW-CAN (For example, Axxess ASWC-1 or Connects2 CTNI001). Connection is made via:

  • 🔌 Orange wire — CAN-High.
  • 🔌 Orange-black wire — CAN-Low.

After connecting the adapter, you must program buttons according to protocol Nissan. To do this:

  1. Turn on the ignition.
  2. Press and hold the button MODE on the steering wheel until the beep sounds.
  3. Press the remaining buttons successively (VOL+, VOL-, ▲, ▼), confirming them by pressing on the radio.

If the buttons are not programmable, check:

  • Correct connection CAN- wires to the adapter.
  • Availability of power on the adapter (usually +12V from the red wire).
  • Compatibility of the adapter with your radio model (some brands, for example, Pioneer, require adapter firmware).
What should I do if the steering wheel buttons do not work after connecting?

If the adapter is connected correctly, but the buttons do not respond, try:

1. Reset the adapter settings (usually by pressing the button for 10 seconds).

2. Update the adapter firmware via PC (for ASWC-1 there is official software from Metra).

3. Check the integrity of the wires CAN-High And CAN-Low (they often break when dismantling the radio).

Where to buy connectors and adapters

Accessories for connecting the radio to Qashqai J10 can be purchased at the following places:

Product Where to buy Approximate price
Adapter Nissan 16-pin to ISO AliExpress, Amazon, local auto wreckers 800–1,500 rub.
Connects2 CTNI001 (with CAN and SWC) Official dealers, AutoSound, ChipTuning 3,500–4,500 rub.
Axxess ASWC-1 eBay, AutoGood, I'll take it 2,500–3,200 rub.
Amplifier walker Bose (DSP) Specialty stores (for example, Car-Sound) 5,000–12,000 rub.

When purchasing on AliExpress Pay attention to reviews - you often come across non-original adapters with incorrect pinouts. It is better to choose sellers with a rating above 98% and the number of orders more than 1,000.

In Russia, adapters can be found in auto electronics stores: AutoSound, ChipTuning, AutoGood, as well as on Avito or Yule (used options).

💡

Before purchasing an adapter, check with the seller whether it supports your radio model and year of manufacture Qashqai J10 (2007–2010 or 2010–2013).

FAQ: Frequently asked questions about pinouts

Is it possible to connect a radio without an adapter?

Theoretically, yes, but you will need to cut off the standard connectors and solder the wires directly. This is risky: you can reverse the polarity or damage the insulation. It's better to use an adapter.

Why does the on-board computer display not work after connecting a new radio?

This happens if not connected CAN bus adapter. B Qashqai J10 The radio transmits data to the display (for example, the name of a track or radio station). Without an adapter this function is lost.

How can I check if my car has a Bose system?

Inspect the speakers - they should be marked Bose. Also check for an amplifier in the trunk (usually under the shelf) or look in VIN-code option B92/B93.

Which fuses are responsible for the radio?

In the block under the hood:

  • F33 (10A) — power supply for the radio.
  • F34 (15A) - amplifier (if available) Bose).

Burns out when short circuited F33.

Is it possible to connect a rear view camera to a new radio?

Yes, but you will need:

  • Wire RCA for video signal.
  • Connect to the reverse wire (usually purple/black in the radio harness).
  • Settings in the radio menu (enable Rear Camera).

B Qashqai J10 There is no standard camera, so it will have to be installed separately.