Nissan Qashqai heater motor: where it is, how to get there and replace it

Owners Nissan Qashqai first (J10, 2006–2013) and second (J11, 2013–2021) generations sooner or later face the problem of weak airflow from the stove or a complete lack of air flow from the deflectors. In 90% of cases it is to blame heater fan motor - its brushes wear out, the bearings jam or the winding burns out. But before you buy a new part, you need to know exactly where it is and how to get to it.

In this article - detailed diagram of the location of the heater motor on all versions of Qashqai, including restyled models of 2010 and 2017, as well as a step-by-step dismantling algorithm. We'll look at what tools you'll need, how to avoid mistakes when disassembling the dashboard, and what to look for when choosing a replacement. If you are not confident in your abilities, at the end of the article there is a diagnostic checklist that will help you make a decision: to repair it yourself or go to a service center.

Where exactly is the heater motor on a Nissan Qashqai?

Heater fan motor (aka stove motor) in Nissan Qashqai located under the glove compartment on the passenger side. More precisely, in a plastic fan housing, which is attached to the car body in a niche in the front panel. Access to it is difficult due to the abundance of plastic panels and air ducts, but it can be removed without completely dismantling the dashboard.

The specific location depends on the generation:

• 🔧 Qashqai J10 (2006–2013): the motor is located at the bottom of the fan housing, closer to the center console. To see it, you need to remove the glove compartment and the lower panel underneath it.
• 🔧 Qashqai J11 (2013–2021): the design is similar, but the fan housing is slightly shifted to the left. Here you will have to additionally unscrew the fastening of the air duct to the pedals.

Important: on diesel versions (1.5 dCi, 1.6 dCi) access may be complicated by additional heat-insulating screens. Also on cars with climate control (Automatic A/C) the motor is often assembled with a resistor that regulates the rotation speed.

Diagram and photo of the location of the stove motor

To visualize where the part is located, take a look at the diagram below. It fits most modifications Qashqai, including versions with petrol (1.6, 2.0) and diesel (1.5 dCi) engines.

element	Location	Notes
Stove motor	Under the glove compartment, in the fan housing	Mounts with 3 bolts (J10) or 4 screws (J11)
Speed resistor	Next to the motor, on the body	On J11 it is often integrated into the connector
Cabin filter	Behind the glove compartment, in a niche	Recommended to be replaced when dismantling
Gas pedal air duct	To the left of the motor	You'll have to unplug it to access it.

The photo below shows the heater motor Nissan Qashqai J10 after removing the glove compartment and lower panel. Pay attention to the power connector (marked in red) - it must be disconnected first to avoid a short circuit.

Photo of Qashqai heater motor

The image shows a fan housing (black plastic) with a motor at the bottom. Two wires come to it: black (ground) and red (plus). On the right is the speed resistor, which often fails along with the motor.

⚠️ Attention: On right-hand drive vehicles (for example, Japanese versions Qashqai) the heater motor can be mirrored - on the driver's side. Before disassembling, check the layout using the VIN code or service documentation.

Signs of a malfunctioning heater motor

Before you climb under the dashboard, make sure that the problem is in the motor. Here are the key symptoms of its malfunction:

• 🌬️ The stove blows weakly or does not blow at all (even at maximum speed).
• 🔊 Extraneous sounds (creaking, squealing, knocking) when the fan is turned on.
• 🔄 Rotation speeds switch chaotically or do not respond to the regulator.
• 💨 The smell of burning from the deflectors (the motor winding burned out).
• 🔋 The stove only works at speed 3-4 (problem with the resistor).

If at least one of these signs is observed, most likely the motor requires replacement. However, check first:

1. fuse (on Qashqai J10 this is F37 (30A) in the block under the hood, on J11 — F20 (40A) in the cabin block).
2. Fan relay (located next to the fuse, designated as R12).
3. Connector terminals - often oxidize or come off.

How to get to the stove motor: step-by-step instructions

To remove the motor, it is not necessary to dismantle the entire dashboard. It is enough to remove the glove compartment, the lower panel and disconnect the air ducts. Here is the detailed algorithm for Nissan Qashqai J10/J11:

Step 1. Removing the glove compartment

On Qashqai J10 The glove compartment is secured with 4 screws (Torx T20) at the bottom and two plastic latches at the top. On J11 added one more screw on the right. Gently pull the glove compartment towards you, disconnect the backlight connector (if equipped) and move it to the side.

Step 2. Removing the bottom panel

Under the glove compartment there is a plastic panel, which is secured with 3 clips and 1 screw (Torx T20). Remove it by pulling it down. Behind it you will see a fan housing with a motor.

Step 3: Disconnecting the Air Ducts

To the left of the motor there is a flexible air duct to the gas pedal - it must be removed by loosening the clamp or snapping the clamps. On Qashqai J11 Additionally, you will have to unscrew the metal bracket holding the wiring harness.

Step 4. Removing the motor

Disconnect the power connector (press the latch and pull it up). Then unscrew the 3 bolts (J10) or 4 screws (J11) attaching the motor to the fan housing. Carefully pull it out along with the impeller.

⚠️ Attention: On some versions Qashqai the motor can be glued to the body with sealant. In this case, do not pull it by force - first warm it up with a hair dryer or carefully pry it around the perimeter with a knife.

Which stove motor to choose for replacement?

Original heater motor for Nissan Qashqai has an article number 27340-JM00A (for J10) and 27340-4M00A (for J11). Cost - from 8,000 to 12,000 rubles, depending on the supplier. However, there are more budget analogues:

Manufacturer	Article	Price, rub.	Notes
Nissan (original)	27340-JM00A / 27340-4M00A	8 000–12 000	Best quality, 1 year warranty
Febi	27340	4 500–6 000	Good analogue, suitable for J10/J11
Valeo	696136	5 000–7 000	High resource, quiet operation
Blue Print	ADM500010	3 500–5 000	Budget option, average quality

When choosing, pay attention to:

• 🔄 Direction of rotation - on Qashqai the motor must rotate clockwise (when viewed from the impeller side).
• 🔌 Connector type - on J11 it may differ from J10 (check by VIN).
• 🔊 Noise level - cheap analogues often squeal at high speeds.

Common mistakes when replacing a heater motor

Even experienced car owners make mistakes when replacing a motor. Here are the most common:

1. Doesn't disconnect the battery - this may lead to a short circuit when the connector is disconnected.
2. Fastenings are loose — the motor vibrates and quickly breaks down.
3. Don't check the resistor - if it burns out, the new motor will not work for long.
4. Confused polarity — the motor will rotate in the opposite direction, the stove will not blow.
5. Do not clean the fan housing — accumulated dirt accelerates wear of the new part.

⚠️ Attention: On Nissan Qashqai J11 with climate control, after replacing the motor, you may need to reset errors in the control unit. To do this:

1. Disconnect the battery terminal for 10 minutes.
2. Plug it back in and turn on the ignition (without starting the engine).
3. Press and hold the button A/C 5 seconds - the system will reboot.

How much does it cost to replace a heater motor at a service center?

If you do not want to disassemble the car yourself, you can contact the service. The cost of work depends on the region and complexity:

• 🔧 Replacing the stove motor - 1,500–3,000 rub.
• 🔧 Heating system diagnostics - 500–1,000 rub.
• 🔧 Replacing the speed resistor - 800–1,500 rub.
• 🔧 Air duct cleaning - 1,000–2,000 rub.

In total with the spare part it will be from 5,000 to 15,000 rubles, depending on the selected motor and region. At official dealerships Nissan the price may be 30–50% higher.

Replacing it yourself will help you save money, but keep in mind: disassembly and assembly will take 2–4 hours, and without experience there is a risk of damaging plastic clips or wiring.

FAQ: Frequently asked questions about the Nissan Qashqai heater motor

Is it possible to repair the heater motor instead of replacing it?

Theoretically, yes - you can replace the brushes, bearings or clean the commutator. However, in practice this is a temporary solution: after 6–12 months the problem will return. Repair is justified only if the motor is rare (for example, for Qashqai right-hand drive) and a new one is difficult to find.

Why does the heater only blow at speed 4?

This is a typical sign of a problem speed resistor, which is located next to the motor. On Qashqai J10 its article number - 27360-JM00A, on J11 — 27360-4M00A. Replacement takes 10 minutes and costs about 1,500 rubles.

How to check a heater motor with a multimeter?

Connect the probes to the motor contacts (polarity is not important). The winding resistance should be 0.5–1.5 Ohm. If the device shows infinity - a break, if 0 - a short circuit. Also check the current consumption: at maximum speed it should not exceed 10–12 A.

What to do if the stove does not work after replacing the motor?

Check:

1. Connection polarity (swap wires).
2. Voltage at the connector (should be 12 V when the fan is on).
3. Fuse and relay (they could burn out during replacement).
4. Condition of the resistor (if it is burnt out, the motor will not work at speeds 1–3).

Will a Renault heater motor fit a Nissan Qashqai?

Yes, but only from specific models. For example, a motor from Renault Koleos (article 27340-4M00A) is completely identical to the original for Qashqai J11. Parts from Renault Megane 3 And Scenic 3. The main thing is the coincidence of the connector and the direction of rotation.