Rear view mirrors Nissan Qashqai J10 (2006–2013) is not just a safety element, but also a part of the design that affects visibility and driving comfort. Owners of this crossover often encounter problems: from simple broken glass to malfunctions of electric drives or heating. In this article, we’ll look at how to choose the right replacement, install it yourself, and avoid common mistakes.

First generation Qashqai (index J10) is equipped with mirrors with different options: from simple mechanical ones to those equipped with electric drive, heating and turn signal indicators. The choice depends not only on the year of manufacture, but also on the configuration - Visia, Acenta, Tekna or 360. We have collected current articles, analogues and step-by-step instructions so that you can solve the problem without extra costs.

Original mirrors and their articles for Qashqai J10

The manufacturer offers several options for mirrors depending on the installation side and functionality. Main part numbers for left (driver) and right (passenger) mirrors:

  • 🔧 Left mirror without heating/electric drive: 26560-JM00A (before 2010) or 26560-JM00B (after 2010).
  • 🔥 Left mirror with heating and electric drive: 26560-JM01A (for complete sets Acenta and above).
  • 🔄 Right mirror with turn signal: 26561-JM01A (only for versions with LED repeaters).
  • ⚡ Right mirror is heated, but not electric: 26561-JM00A (basic configurations).

It is important to consider that mirrors are for Qashqai J10 not interchangeable with models J11 (second generation). Also, some SKUs may differ for markets. Europe (JM0) and Japan (JM1). Before purchasing, check the vehicle's VIN or part number on an old mirror (usually located on the inside of the housing).

📊 Which mirror are you planning to replace?
  • Left (driver's)
  • Right (passenger)
  • Both
  • I don't know, I need to determine

Analogues and non-original substitutes: what to choose?

Original spare parts from Nissan They are expensive - from 8,000 to 15,000 rubles per piece. An alternative is certified analogues from trusted brands:

Brand Article Mirror type Average price, ₽ Features
Febi Bilstein 26560 Left with heating 5 200 The quality of the glass is close to the original, but the plastic of the case is less durable.
Hella 8GC 355 007-031 Right with repeater 6 800 Fully compatible with LED repeaters, but requires connection to the control unit.
Mitsuba MZ-101L Left with electric drive 7 500 Made in Japan, ideal for versions with Bose And Panoramic Roof.
Depo 335-1122L Left without heating 3 900 A budget option, but there are often complaints about the durability of the folding mechanism.

When choosing an analogue, pay attention to:

  • 🔍 Electrical compatibility: some mirrors require modification of the connectors.
  • 🛠️ Fastening quality: cheap models can play at speeds above 100 km/h.
  • 💡 Availability of certificate: Uncertified parts may not pass inspection.
⚠️ Attention: Mirrors from Renault Koleos (first generation) are similar in appearance, but have a different connection connector. Their installation will require resoldering the contacts or using an adapter.

Step-by-step instructions for replacing a mirror

Replacing the mirror with Qashqai J10 does not require special tools, but it is important to follow the algorithm so as not to damage the wiring or plastic clips. You will need:

  • 🔧 Flat screwdriver or plastic pick.
  • 🔌 Multimeter (to check the heating circuit).
  • 🧴 Silicone grease (for processing seals).

Step 1: Removing the inner door trim

Remove the plastic trim by prying it off the door handle with a screwdriver. Be careful - the clips are fragile! Disconnect the lock connector and lower the window all the way (if the mirror is electric).

Step 2: Power Off

Unscrew the three mirror mounting bolts (under the decorative plug). Before disconnecting the connector, check the presence of voltage at the contacts with a multimeter 12V And GND - This will help diagnose wiring problems.

Disconnect battery (to avoid short circuit)

Take a photo of the location of the wires

Check the integrity of the rubber seal

Prepare a new mirror (remove the protective film from the glass) -->

Step 3: Installing a New Mirror

Connect the connector to the new mirror, secure it with bolts and check the operation of all functions (heating, folding, repeater). If the mirror is powered, calibrate:

  1. Turn on the ignition.
  2. Press the mirror folding button and hold it for 10 seconds.
  3. The mirror will automatically return to its neutral position.
⚠️ Attention: If after replacement the mirror “shakes” at high speed, check the tightness of the sealing rubber. Often the problem is solved by replacing it (part number 80350-JM00A).

Mirror adjustment and calibration

Correct adjustment of mirrors Qashqai J10 critical for safety - an incorrect viewing angle can create a “dead zone” of up to 3 meters. Follow these guidelines:

  • 👁️ Left mirror: Should cover 1/4 of the rear fender and the road up to 50 meters away.
  • 🚗 Right mirror: Adjust so you can see the edge of the rear bumper and the traffic lane.
  • 🔄 Electric drive: if the mirrors “go astray” after folding, the control unit must be re-flashed (BCM).

For vehicles with Around View Monitor (360° camera) mirror calibration is performed automatically when the ignition is turned on. If the screen image is distorted, perform a factory reset through the menu Settings → Camera → Calibration.

💡

If the power mirror moves jerkily, clean the mechanism guides from dirt and apply lithium grease. This will extend the life of the motor by 30–50%.

Typical faults and repair methods

Mirrors on Qashqai J10 are subject to several characteristic failures. Let's look at their reasons and solutions:

Malfunction Reason Solution
Heating does not work Fuse blown F37 (10A) or a broken chain in the door. Check the fuse, test the wires with a multimeter. If there is a break, solder or replace the harness.
Mirror doesn't fold The motor or control unit has failed BCM. Replace the motor (part no. 28550-JM00A) or reset settings BCM through Nissan Consult.
The turn signal does not flash Contact oxidation or unit malfunction Combination Switch. Clean the contacts, check the lamp (7440NAK for LED version).
The glass fogs up from the inside The seal of the housing is broken. Disassemble the mirror, dry it and seal the joints sealant for auto glass.

Critical Feature: On Qashqai J10 with the system Keyless Go Immobilizer antennas are installed in the mirrors. If you replace the mirror without moving the antenna, the key may not be recognized!

How to check the functionality of heated mirrors?

Connect the multimeter to the mirror connector contacts in resistance measurement mode. For proper heating, the resistance should be within the range 1.5–3 Ohm. If the readings tend to infinity, the circuit is open.

Review of the best mirrors from AliExpress and other markets

If original spare parts are too expensive, you can consider options with AliExpress, eBay or Russian sites. The main thing is to choose sellers with a rating above 98% and reviews of compatibility with Qashqai J10.

  • 🌍 Mirror with rear view camera: article CV-NIS-Q10-L (price ~4,500 ₽). Suitable for installation instead of the standard one, but requires connection to the radio.
  • 🔋 Mirror with wireless charging: model AutoVox M1 (from 6,000 ₽). Attaches to the standard mirror, but may interfere with your view.
  • 💎 Auto-dimming mirror: Gentex 24A (from 12,000 ₽). Only compatible with versions without Around View Monitor.

When purchasing, please specify:

  • 📏 Mounting dimensions: must match the original (120×80 mm for the base).
  • 🔌 Connector type: Some Chinese mirrors come with universal EU connectorwhich is not suitable for Qashqai.
  • 📄 Availability of certificate: without it, the mirror may not be accepted at the service station during technical inspection.
💡

Before purchasing a mirror from AliExpress, be sure to ask the seller for a photo of the connector and fastening - even if the article number is the same, there may be differences!

Modernization: how to improve standard mirrors

Owners Qashqai J10 Mirrors are often upgraded to improve functionality. Here are some proven solutions:

  • 🔦 Additional LED repeaters: Can be installed in the mirror housing (such as tape SMD 5050 with resistor 150 Ohm).
  • 📹 Rear view camera: Built into the right mirror (suitable for camera Boyo VTL375 with viewing angle 170°).
  • 🔋 Heating for mechanical mirrors: use heating element Defa 47901 (requires soldering and insulation).

To install the camera you will need:

  1. Remove the door trim and mirror.
  2. Drill a hole with a diameter 16 mm at the bottom of the body.
  3. Connect the camera to the rear light wires (+12V And mass).
  4. Route the video cable to the radio (through the door seal).
⚠️ Attention: When installing additional equipment (such as a camera), do not connect it directly to the heated mirror wires - this may overload the fuse F37.

FAQ: Frequently asked questions about mirrors Nissan Qashqai J10

Is it possible to install mirrors from Qashqai J11 on J10?

No, second generation mirrors (J11) have a different mounting size and body shape. In addition, the connection connectors are not compatible. The exception is some mirrors from Renault Koleos (2008–2013), but they require improvement.

Why doesn't the heating work after replacing the mirror?

The reasons may be the following:

  1. The heating connector is not connected (check the contacts 1 And 2 on the connector).
  2. Fuse blown F37 (located in the fuse box under the steering wheel).
  3. Broken wire in the door corrugation (a common problem with frequent openings).

For diagnostics, use a multimeter in dial mode.

How to adjust the mirror if the electric drive does not work?

If the motor fails, you can manually adjust the mirror:

  1. Remove the decorative plug from the inside of the door.
  2. Loosen the three mirror mounting bolts (do not unscrew completely!).
  3. Manually set the desired angle and tighten the bolts.

This is a temporary solution - for permanent use it is recommended to replace the motor.

What to do if the mirror fogs up from the inside?

Fogging indicates a seal failure. Solution:

  1. Remove the mirror and disassemble the housing (carefully prying up the latches).
  2. Dry the glass and internal parts with a hairdryer (temperature no higher than 60°C).
  3. Apply sealant (eg ABRO GS-1000) at the joints and assemble the mirror.

If the problem persists, replace the rubber seal (part no. 80350-JM00A).

Can the mirror body be painted a different color?

Yes, but with reservations:

  • Use only auto enamel with a primer (for example, Mobihel or Kudo).
  • Degrease the surface before painting White spirit.
  • Apply 2-3 layers with intermediate drying (24 hours).
  • After painting, treat with varnish to protect against chipping.

Do not paint the glass - it will impair visibility!