Replacing rear silent blocks on a Nissan Qashqai J10: detailed guide with photos and videos

Rear silent blocks on Nissan Qashqai J10 - one of those suspension elements that wear out faster than others. With a mileage of 80,000 km (and on Russian roads even earlier), they begin to “knock”, causing play in the levers and worsening controllability. If you notice squeaking noise when going over bumps, uneven wear on the rear tires, or you feel like the car is “floating” at speed - it’s time to check the silent blocks.

In this article we will look at complete replacement of rear silent blocks on Qashqai J10 (2007–2013) with your own hands: from diagnostics to pressing in new parts. You will learn what tools you will need, how to avoid common mistakes (for example, damage to the lever when pressing out) and what spare parts to choose so that you do not have to redo the work after 20,000 km. For clarity, let's attach photos of key stages and a video of the process.

Signs of wear on the rear silent blocks on the Qashqai J10

Silent blocks (or rubber-metal hinges) dampen vibrations between the suspension arms and the body. When the rubber cracks or peels off from the metal bushing, characteristic symptoms appear:

• 🔊 Knocking or squeaking when driving over speed bumps or potholes - especially noticeable on the rear axle.
• 🚗 Pulling the car to the side when braking or accelerating (even with straight wheels).
• 🔄 Uneven rear tire wear - usually on the inside of the tread.
• 🛣️ "Floating" rear at speeds above 80 km/h - the car reacts to bumps with a delay.

On Qashqai J10 The rear silent blocks suffer more often than the front ones due to the design of the multi-link suspension. Particularly vulnerable inner silent blocks of lower arms - their resource rarely exceeds 100,000 km. You can check their condition visually: if cracks are visible on the rubber or it “crawls out” of the metal casing, replacement cannot be put off.

⚠️ Attention: If you ignore the wear of silent blocks, this will lead to play in the lever mount, which can cause loss of control at high speed. On Qashqai J10 With a mileage of more than 150,000 km, the levers themselves often break due to broken silent blocks.

Which silent blocks to choose for replacement

On Nissan Qashqai J10 Two types of silent blocks are installed:

1. Rear lower control arms — internal and external silent blocks (articles 54501-JM00A And 54501-JM00B).
2. Rear upper control arms — only internal silent block (article no. 54501-JM01A).

Original spare parts from Nissan are expensive (from 2,500 rubles per piece), but last longer than analogs. Among the popular substitutes:

Brand	Article	Price (per piece)	Features
Nissan (original)	54501-JM00A	2 500–3 200 ₽	Soft rubber, long life
Febi	22610	1 200–1 500 ₽	Stiffer than the original, suitable for aggressive driving
Sasic	2005040	800–1 000 ₽	Budget option, resource ~50,000 km
TRW	JTC1144	1 800–2 200 ₽	The quality is close to the original, often counterfeited

When choosing, pay attention to rubber material: on Qashqai J10 it is better to install polyurethane silent blocks (for example, Powerflex), if the machine is operated in difficult conditions (off-road, frequent loads). They are more expensive, but do not “tan” in the cold and last 2–3 times longer than standard ones.

Tools and preparation for replacement

To replace the rear silent blocks with Qashqai J10 you will need:

• 🔧 Silent block remover (hydraulic is better, but screw is also suitable).
• 🔨 Socket heads for 17, 19 and 21 mm + extension.
• 🔩 Torque wrench (bolt tightening torque: 80–100 Nm).
• 🛠️ Hammer, chisel, WD-40 - for knocking out soured bolts.
• 🚗 Jack and stops (or a lift if there is access).

Before starting work:

1. Place the machine on a level surface and fix the front wheels stops.
2. Loosen the wheel and rear control arm bolts before jacking up.
3. Treat all threaded connections WD-40 1–2 hours before replacement.

⚠️ Attention: On Qashqai J10 The lever mounting bolts often stick to the bushings. If you can’t unscrew it, don’t use force! It is better to cut new bolts (part number 08922-60010) and carefully drill out the old ones.

Step-by-step replacement instructions

Let's look at the replacement using an example lower rear arm (the most labor-intensive process). For the upper arm, the algorithm is similar, but simpler - there is only one silent block.

1. Removing the lever

Raise the rear of the car with a jack and remove the wheel. Then:

1. Unscrew bolt securing the arm to the subframe (19 mm head).
2. Disconnect anti-roll bar (14 mm bolt).
3. Unscrew bolt securing the lever to the hub (21 mm head).
4. Carefully lower the lever down - it should come out of the groove.

2. Pressing out old silent blocks

Use a puller:

1. Place the lever in a vice and secure.
2. Place the puller on the silent block and gradually press it out by rotating the screw.
3. If the silent block is “stuck”, it can help heating with a gas burner (but do not overheat - the rubber may catch fire!).

For internal silent block lower arm may be needed special mandrel (article NV-001-003), since it sits deep in the eyelet.

3. Installation of new silent blocks

Before pressing:

• Clean the seat from rust and dirt.
• Lubricate inner surface of the silent block soap solution (not oil!).
• Install the silent block into the mandrel and press it in strictly perpendicular lever

After pressing, check that the rubber is not distorted. If the silent block sits crooked, press it out and repeat the procedure.

4. Assembly and tightening

Reinstall the lever and tighten the bolts in the order:

1. Bolt fastening to the subframe (tightening torque - 100 Nm).
2. Bolt fastening to the hub (torque - 80 Nm).
3. Stabilizer bolt (torque - 40 Nm).

Tighten the bolts only under load — the car must be lowered onto its wheels or the suspension must be loaded with a jack.

Common mistakes and how to avoid them

Even experienced craftsmen make mistakes when replacing silent blocks with Qashqai J10. Here are the most common:

• 🔧 Distortion during pressing — if the silent block is crooked, it will quickly break. Always use a mandrel!
• 🔩 Tightening bolts without load - this leads to play and knocking. Be sure to load the suspension before tightening.
• 🛠️ Using oil for lubrication - it corrodes the rubber. Soap solution only!
• 🚗 Replacing only one silent block — always change in pairs (left + right), otherwise the suspension will work unevenly.

Another common problem is damage to anthers during installation. On Qashqai J10 The boots of silent blocks often tear if they are not lubricated before pressing. This leads to dirt getting in and rapid wear.

What happens if you don’t replace silent blocks on time?

When the silent block is completely destroyed, the metal bushings begin to play, which leads to:

- Loss of control when cornering (especially at high speed).

- Breakage of the lever attachment to the subframe (requires welding).

- Accelerated wear of ball joints and wheel bearings.

- Uneven tire wear (you will have to change tires after 10–15 thousand km).

Cost of replacement in the service vs on your own

Prices for replacing rear silent blocks with Qashqai J10 services vary depending on the region:

Service type	Cost of work (per side)	Cost with spare parts (original)
Official dealer Nissan	4 000–6 000 ₽	12 000–15 000 ₽
Unofficial service	2 500–4 000 ₽	8 000–10 000 ₽
On your own	0 ₽ (if you have a tool)	3 000–5 000 ₽

Self-replacement costs 2–3 times less, but requires silent block remover (can be rented for 500–1,000 rubles). If you do not have experience, it is better to entrust the work to professionals - mistakes during replacement can be more expensive.

Video instructions and additional materials

For clarity, we recommend watching a video with the replacement process on Nissan Qashqai J10:

Video 1: Complete replacement of rear silent blocks (Do-It-Yourself Auto Repair channel) - shows the process of pressing out and pressing in using a homemade puller.

Video 2: Mistakes when replacing silent blocks (Nissan Club channel) - analysis of typical jambs and how to avoid them.

It is also useful to download repair manual Qashqai J10 (for example, from Haynes), where there are diagrams of tightening torques and dimensions of silent blocks.

FAQ: Frequently asked questions about replacing silent blocks

Is it possible to drive with knocking silent blocks?

Short term (1-2 weeks) is possible, but risky. With severe wear, the metal bushings begin to play, which can lead to broken lever or loss of control on a rough road. If the knocking is heard constantly, it is better not to delay replacement.

Do I need to do a wheel alignment after replacement?

On Qashqai J10 the rear wheels have slight negative camber (about -1°). If you only changed the silent blocks and did not touch the levers, you don’t have to do the wheel alignment. But if you notice uneven tire wear, check the wheel alignment angles.

Which puller is better to use?

For Qashqai J10 will do universal hydraulic puller (For example, KUKKO 21-1) or screw with mandrel set. The main thing is that the kit includes a mandrel for the inner silent block of the lower arm (diameter 40 mm).

Is it possible to replace silent blocks without removing the lever?

Theoretically it is possible, but highly not recommended. Without removing the lever, you will not be able to properly press in the new silent block, and you also risk damaging the threaded connections. It’s better to spend an extra 30 minutes on dismantling than to redo it later.

How long does it take to replace?

If you have the tools and experience - 2–3 hours on both rear control arms. If you are doing it for the first time, allow 4-5 hours (especially if the bolts are stuck).