Fog lights (PTF) on Nissan Note E11 - not just a tuning element, but an important safety component. Over time, the lamps dim, the housing becomes cloudy, and the contacts oxidize, reducing visibility in poor weather conditions. If you notice that the light has become yellower and the brightness has dropped by 30-40%, it’s time to think about replacing it.

In this article we will look at all stages of PTF replacement on Nissan Note E11 (2006–2013): from choosing lamps to adjusting the angle of inclination. We will pay special attention hidden bumper mounts, which are often broken during disassembly, and the nuances of connecting relays for xenon/LED. The material is suitable for original headlights 26060-4M000, and for universal analogues.

1. Which lamps are suitable for the PTF of Nissan Note E11?

B Nissan Note E11 halogen lamps are installed as standard H8 (power 35 W). However, the market offers dozens of alternatives - from budget to premium. Here are the key selection criteria:

  • 🔦 Halogen - original Osram H8 12V 35W (article 64210) or Philips VisionPlus (+60% light). Service life ~500 hours, price from 400 rub. for a couple.
  • 💡 LED lamps - optimal Morimoto XB LED H8 or Diode Dynamics SL1. They consume 20 W, but produce a luminous flux of 2000–2500 lm. Important: they require anti-glare lenses (otherwise blinding oncoming people).
  • ⚡ Xenon (D2S/D2R) - prohibited in the Russian Federation for PTF (fine 500 rubles under Article 12.5 of the Administrative Code), but some put Morimoto Mini D2S 4300K. It is necessary to modify the headlight housing (install a lens) and connect it via a relay.

⚠️ Attention: Lamps with a higher color temperature 4300K (for example, 6000K or 8000K) produce a blue tint that does not penetrate fog well. The optimal range for PTF is 3000K–4300K (yellow-white light).

Lamp typeModelLuminous Flux (Lm)Service life (h)Price (per pair)
HalogenOsram Original H8800500400–600 rub.
LEDMorimoto XB LED H8220030 0003500–4500 rub.
XenonPhilips D2S 4300K32002000RUB 5,000–7,000*
Improved halogenPhilips RacingVision H811004501200–1500 rub.

* The price includes the ignition unit and lenses.

📊 Which lamps do you prefer for PTF?
  • Halogen
  • LED
  • Xenon (despite the ban)
  • I haven't decided yet

2. Tools and preparation for replacement

To work you will need:

  • 🔧 Screwdriver set: Phillips (PH2), flat, torx T20 (for some model years).
  • 🔨 Plastic spatulas for removing clips (so as not to break the bumper latches).
  • 🔌 Multimeter (checking the voltage at the PTF connector).
  • 🧴 Silicone grease for rubber seals (if you install LED/xenon).
  • 📦 New lamps + gloves (Do not touch the halogen bulb with your bare hands!).

⚠️ Attention: If you have Nissan Note E11 with the system IDAS (smart access), before removing the bumper disconnect the battery! Otherwise an error will occur U1000 (loss of connection with the body block).

Disconnect the battery (if there is IDAS)|Remove the negative terminal|Prepare the workplace (lighting, windless area)|Check the new lamps for functionality (with a multimeter)|Take a photo of the location of the bumper clips-->

3. Removing the bumper: step-by-step instructions with photos

The main difficulty when replacing PTF with Note E11 — dismantling the front bumper. It is secured with 8 clips and 4 bolts. Do not pull the bumper by force - this way you will break the latches (cost ~300 rubles apiece). Follow the algorithm:

  1. Remove the front wheels (or turn them all the way left/right to access the arches).
  2. Unscrew the bolts securing the bumper to the arches (2 on each side, 10 mm).
  3. Disconnect the clips under the radiator grille (3 pcs.): Gently pry with a spatula and pull up.
  4. Remove the bottom clips (under the front spoiler, 2 pcs.). Plastic is often broken here - proceed with caution!
  5. Disconnect the PTF and DRL connectors (if any). Remember their location or take a photo.

After removing the bumper you will see the PTF housing attached to 3 bolts (two on the bottom, one on the side). Unscrew them and carefully pull out the headlight without pulling the wires.

What to do if the clip breaks?

If the bumper latch is cracked, do not try to glue it with superglue - it will not hold the plastic under load. Buy a repair kit of clips for Nissan Note (article 77230-4M000, ~500 rub. for 10 pcs.). For temporary fastening, you can use plastic ties, but this will not last long - the bumper will “walk”.

4. Replacing a lamp or the entire headlight: nuances

If the PTF housing is intact, it is enough to change the lamp. To do this:

  1. Remove the rubber boot from the back of the headlight.
  2. Press out the metal lamp retainer (press down and turn counterclockwise).
  3. Take out the old lamp without touching the flask (for halogen). For LED/xenon use gloves.
  4. Install a new lamp, secure the clamp and check the seal of the boot.

If the headlight housing is cracked or cloudy, the entire assembly will have to be replaced. Original PTF for Note E11 come with article number 26060-4M000 (left) and 26061-4M000 (right). Analogues from TYC or Depo 30–40% cheaper, but may have worse light transmittance.

💡

Before installing a new lamp, clean the contacts of the PTF connector from oxidation with alcohol or a special cleaner (for example, Kontakt 60). This will extend the lamp life by 20–30%.

5. Connecting LED or xenon: circuit with relay

LED lamps and xenon consume less current than halogen, so standard wiring may produce an error B2605 ("Open PTF circuit"). To avoid this, you need to set ballast resistance (for LED) or relay (for xenon).

Connection diagram via relay:



[Аккумулятор +12V] → [Предохранитель 10A] → [Реле 87]


[Реле 85] → [Масса]


[Реле 86] → [Штатный +12V ПТФ (после кнопки)]


[Реле 30] → [Блок розжига/LED-драйвер] → [Лампа]

For Nissan Note E11 a relay will do 904.3747-10 (from Bosch). Ballast resistance for LED: 6 Ohm, 50 W (installed parallel to the lamp).

💡

If, after installing the LED/xenon, the PTF error appears on the device, check the polarity of the connection. On Note E11 “plus” goes along the yellow-green wire, “minus” goes along the black one.

6. Setting the tilt angle of the PTF

After replacing lamps or headlights be sure to adjust the light beam. An incorrect angle of inclination leads to dazzling of oncoming drivers (especially important for LED/xenon). You will need:

  • 📏 Roulette and level.
  • 🪛 Adjusting screw (located on top of the PTF housing).
  • 🚗 Flat area and wall at a distance of 5 meters.

Adjustment algorithm:

  1. Place the machine on a flat surface (not inclined).
  2. On the wall, draw a horizontal line at the height of the centers of the PTF (usually 40–50 cm from the ground).
  3. Turn on the PTF and mark the upper boundary of the light spot on the wall.
  4. Turn the adjusting screw until the border is 5–10 cm below the horizontal line.

⚠️ Attention: On Nissan Note E11 With factory PTF, the angle of inclination is adjustable only in the vertical plane. If the light “goes” to the left/right, check the headlight mount or the integrity of the housing.

7. Common mistakes and how to avoid them

Even experienced car owners make mistakes when replacing PTF. Here are the most common:

  • 🔌 Reversed polarity — leads to LED blinking or xenon failure. Always check with a multimeter: on the PTF connector +12V should be on the yellow-green wire.
  • 💦 Moisture getting into the headlight — if you do not seal the boot, condensation will damage the reflector. Use silicone sealant ABRO ES-350.
  • 🔧 Broken bumper clips — 80% of problems during disassembly are related to them. Buy spares in advance (item number 77230-4M000).
  • 🔦 Incompatible lamps - for example, LED with a radiator that is not included in the headlight housing. Check the dimensions before purchasing!

If the PTFs do not light up after replacing, check:

  1. fuse F37 (10A) in the block under the hood.
  2. Relay K30 (responsible for PTF).
  3. The integrity of the wiring from the power button to the headlights (often frays near the pedal assembly).

FAQ: Answers to frequently asked questions

Is it possible to install LED lamps without modifications?

Technically yes, but there will be an error on the device (due to low current consumption). To remove it, you need to either flash the ECU (which is difficult) or install a ballast resistor (6 Ohms, 50 W) parallel to the lamp. Also check whether the LEDs do not blind oncoming drivers - the reflector often requires modification.

Which xenon can be legally installed in PTF?

In Russia any xenon is prohibited in PTF (clause 3.4 of Appendix 8 to the Technical Regulations of the Customs Union). An alternative is halogen lamps with increased brightness (for example, Philips RacingVision) or certified LED modules with marking E22 (but they are difficult to find for Note E11).

How much does it cost to replace a PTF at a service?

The cost of work depends on the region:

  • Lamp replacement: 500–800 rub. (for one headlight).
  • Replacing the entire headlight: 1500–2500 rubles. (bumper removal/installation included).
  • Light adjustment: 300–500 rub.

Replacing it yourself will save up to 70%, but requires caution (risk of breaking the bumper clips).

Why do new PTFs shine worse than old ones?

The reasons may be as follows:

  1. Oxidation of contacts in the connector - clean them with alcohol.
  2. Incorrect polarity - check with a multimeter.
  3. Diffuser is cloudy - polish it with paste 3M 09374.
  4. Low-quality lamps - especially important for cheap LEDs (<1000 rub.).

Do I need to remove the bumper to replace the bulb?

Technically you can do without complete removal, but this is extremely inconvenient. Alternative way:

  1. Remove the wheel and fender liner from the desired side.
  2. Unscrew the PTF fastening bolt from below (access through the arch).
  3. Carefully pull out the headlight without completely detaching the bumper.

⚠️ Risk: you can damage the wiring or break the headlight mount. We recommend removing the bumper.