Replacing side lights on a Nissan Juke: a detailed guide with photos and tips

Replacing side lights with Nissan Juke - a task that every owner of this compact crossover faces sooner or later. Regardless of the generation (F15, 2010–2019 or J11, from 2019), the procedure has its own nuances that are important to consider in order to avoid damage to plastic elements or electrical components. In this article, we will analyze not only the standard replacement instructions, but also tell you how to choose lamps taking into account luminous flux and durability, which tools are really necessary, and which you can do without.

Feature Juke — compact engine compartment and specific headlight design, where access to the headlights is often difficult due to closely located air ducts or the battery. If you have never worked with automotive optics, your first experience may take up to an hour - but with our tips you will cut this time in half. We will also reveal One Little Known Trick With Chuck Locks That Saves 20 Minutes in Removal.

Which lamps are suitable for Nissan Juke dimensions?

B Nissan Juke The first and second generations use different types of lamps for the front and rear position lights. An error in selection can lead not only to dim light, but also to melting of the cartridge or even a short circuit. Here are the current data on the models:

Generation	Year of manufacture	Front dimensions	Rear dimensions	Power, W
F15 (1st)	2010–2014	W5W (baseless)	P21/5W (double strand)	5 / 21/5
F15 (restyling)	2015–2019	W5W or T10	P21/5W or 7528	5 / 21/5
J11 (2nd)	2019–present time	W5W (LED compatible)	P21/5W or 7443	5 / 21/5

For replacement, we recommend sticking to the original specifications, but if you want to improve the light, pay attention to LED analogues with markings CAN-BUS — they do not cause errors on the dashboard. For example, lamps Osram LEDriving W5W or Philips X-tremeUltinon provide 150% more light with the same energy consumption. However, please note: in some versions Juke (especially with the system NissanConnect) LED lamps may require additional resistors to operate correctly.

• 🔹 Original lamps: Nissan 28550-JM00A (W5W) or 26150-JM00A (P21/5W) - reliable, but dim.
• 💡 Improved halogens: Osram Night Breaker or Philips RacingVision — +130% brightness.
• 🔋 LED option: Morimoto XB LED or Diode Dynamics — durability up to 50,000 hours.
• ⚠️ What to Avoid: Cheap Chinese LEDs without drivers overheat and melt the cartridges.

⚠️ Attention: B Nissan Juke J11 (2019+) with full LED headlights, replacing headlights may void the warranty on the optics. Please check dealership conditions before proceeding.

Tools and materials: what you need for replacement

To change dimensions to Juke You don’t need a professional set—a basic tool is enough. However, there are a couple of nuances that are often forgotten:

• 🔧 Screwdriver with Phillips bit (preferably magnetic) - for headlight mounting screws on restyled models.
• 🪛 Flathead screwdriver or plastic pick — for prying off the socket holders (especially important for rear lights).
• 🧤 Nitrile gloves — protect lamps from grease from fingers (even on LEDs this is important!).
• 🔦 Flashlight or head light - engine compartment in Juke dark, especially near the battery.
• 🧴 Silicone grease — for treating rubber headlight seals (prevents sticking).

If you are working with rear lights, additionally prepare:

• 🔑 10 mm wrench — to unscrew the flashlight mount in the trunk.
• 🧲 Magnet on telescopic handle - so as not to drop the screws into the casing.

For models with Nissan Safety Shield (driver assistance system) may be required OBD-II scanner to reset errors after replacing lamps. For example, if you installed LEDs in the dimensions, and the system recognizes them as burnt out.

Step-by-step instructions: replacing front markers

Replacement process Nissan Juke F15 And J11 similar, but there are differences in access to the cartridge. Let's start with the first generation (2010–2019):

1. Disconnect the negative battery terminal - this is a must, even if you are an experienced auto electrician. B Juke The size wires go directly to the fuse box, and a short circuit can damage the relay.
2. Remove the headlight protective cover. On F15 it is attached to 3 plastic latches, on J11 — on 2 screws for a Phillips screwdriver. Carefully pry up the cover using a flathead screwdriver, starting from the top corner.
3. Find the cartridge size. On F15 it is located closer to the wing, on J11 — closer to the radiator. The socket is white or gray, with two wires (red and black).
4. Turn the chuck counterclockwise 45° and remove it. This is where many people make a mistake: they try to pull the cartridge out by force without turning it. It breaks the latches!
5. Replace the lamp, pressing on it and turning it counterclockwise. The new lamp is installed in the reverse order.

For Nissan Juke J11 (2019+) there is an additional nuance: on some versions the socket cartridge is blocked by a plastic bracket. To remove it, you need to press the center of the bracket and pull it up. Without this, the cartridge will not turn!

Disconnect the battery|Remove the headlight protective cover|Find the lamp socket (white/gray)|Turn the socket 45° against the emergency direction|Remove the old lamp, install a new one-->

After installing a new lamp, check its operation without removing the headlight housing. If the light does not light, check:

• 🔌 Correct connection of the cartridge (wires should not be twisted).
• 💡 Integrity of the filament (even a new lamp can be defective).
• 🔧 Fuse F37 (10A) in the block under the steering wheel - it is responsible for the dimensions.

⚠️ Attention: On Juke with xenon headlights (Bi-Xenon) replacing dimensions may require flashing the light control unit. If after installation the lamp flashes or stays on at full intensity, contact an auto electrician.

Replacing rear dimensions: features and pitfalls

Rear dimensions on Nissan Juke It is more difficult to change the front ones due to the need to dismantle the lamp. The process takes 30-40 minutes, but if you rush, you can break the plastic clips of the trunk trim.

Instructions for F15 (2010–2019):

1. Open the trunk and remove the plastic trim on the threshold (it is attached to 4 clips). Pry it off with a flathead screwdriver, starting at the corner near the hinge.
2. Unscrew the two screws securing the lamp (10 mm wrench). They are located at the base of the lamp, closer to the body.
3. Carefully pull the flashlight out, pulling it towards you. Don't pull the wires! The lantern has another latch on top - you need to press it out.
4. Rotate the socket (it is black) counterclockwise and remove the lamp P21/5W.

On Juke J11 (2019+) the process is simpler: the flashlight is attached to 3 plastic clips, which are snapped off manually. However, there is a risk of damage glass heating wiring, if you pull the flashlight too sharply.

When installing a new lamp P21/5W pay attention to two filaments: one is responsible for the clearance (5W), the second is for the brake light (21W). If the brake light does not work after replacement, it means the lamp is installed on the wrong side.

Common mistakes and how to avoid them

Even experienced car owners make mistakes when replacing dimensions with Juke. Here are the most common ones and how to prevent them:

• 🔧 Broken chuck latches. Reason: attempt to pull out the cartridge without turning. Solution: Always rotate the chuck 45° counterclockwise before removing.
• 💥 Short circuit. Occurs if the positive wire touches ground. Solution: Disconnect the battery and use dielectric gloves.
• 🌡️ Overheating of LED lamps. Cheap LEDs without radiators melt cartridges. Solution: Buy lamps with an aluminum body and a fan.
• 🚨 Error on the dashboard. Appears when installing LED in cars with CAN-BUS. Solution: Use lamps with a built-in resistor or decoy unit.

Another typical problem is headlight fogging after replacement. This happens if the rubber seal is damaged or the protective casing is not tightly closed. To avoid this, after installing the lamp, check the tightness by spraying the headlight with water from a hose (without pressure!). If condensation appears inside after 10 minutes, the seal must be replaced.

What should I do if the light blinks after replacement?

If the new lamp blinks or is lit at full intensity, the problem may be:

1. **Poor contact** - check the cartridge for oxidation (clean with sandpaper).

2. **LED Incompatibilities** - Install a 50 ohm resistor in parallel with the lamp.

3. **Malfunctions of the control unit** - diagnostics with a scanner is required (error B2601).

When to contact the service

Although replacing the dimensions with Nissan Juke - a procedure that can be performed independently, in some cases it is better to trust professionals:

• 🔧 If, when dismantling the headlight, you broke the plastic retainer or socket. The service will replace it without the risk of damaging the optics.
• 💡 If, after replacing the LED lamps, errors appear on the device, and the deception unit does not help. Firmware for the light control unit will be required.
• 🌧️ If condensation has accumulated inside the headlight, and self-drying (with a hairdryer or silica gel) did not help. The glass may be cracked or the seal may be broken.
• ⚡ If, when replacing, you shortened the wires, and now other devices (for example, interior lighting or a radio tape recorder) do not work.

Average cost of replacing dimensions in the service for Juke:

• 💰 Replacing one lamp—500–800 rubles.
• 💰 Electrical diagnostics - 1000–1500 rubles.
• 💰 Firmware for the light control unit - 2000–3000 rubles.

If you decide to go to a service center, take the original lamps with you (even if they are burned out) - this will help the technician quickly select analogues.

Tips for extending the service life of dimensions

To ensure that the lamp dimensions on your Nissan Juke last longer, follow these recommendations:

• 🔋 Don't include dimensions unnecessarily. In the urban cycle, daytime running lights are sufficient (DRL).
• 💧 Wash headlights with special products. Aggressive detergents (for example, for wheels) destroy the protective coating of the glass, which leads to clouding and overheating.
• 🌡️ Check the on-board voltage. If the generator produces more than 14.5V, incandescent lamps will burn out 2-3 times faster. The norm is 13.8–14.2V.
• 🔧 Clean the cartridge contacts regularly. Oxidation increases resistance, which leads to overheating. Use a spray Contact Cleaner.

For owners Juke with LED dimensions:

• 🔋 Check the headlight ventilation. LED lamps are sensitive to overheating. If the headlight fogs up frequently, install an additional breather valve.
• 💡 Avoid cheap Chinese LEDs. They often have an unstable driver, which leads to flickering and premature failure.

FAQ: Frequently asked questions about replacing dimensions on a Nissan Juke

Is it possible to replace halogen lights with LED lights without errors?

Yes, but you need to choose lamps with markings CAN-BUS or Error-Free. For Juke J11 (2019+) may need to install 50 ohm resistors in parallel with each lamp. An alternative is to flash the light control unit, but this will void the warranty.

What color of lamps is allowed by traffic regulations for dimensions?

According to GOST R 51709-2001, the front dimensions must be white or yellow, rear - red. The use of blue, green or other colors is prohibited and is punishable by a fine (Part 3 of Article 12.5 of the Administrative Code - 500 rubles).

What should I do if, after replacement, the indicator lights up dimly?

There are several reasons:

1. Poor contact in the cartridge - clean the terminals with sandpaper.
2. Low voltage in the on-board network - check the generator.
3. The lamp is not original - some Chinese analogues have reduced power.

If the problem persists, measure the voltage at the cartridge with the lights on. The norm is 12–14V.

Is it possible to change the dimensions without removing the headlight?

On Nissan Juke F15 (2010–2019) front dimensions can be changed without removing the headlight - just remove the protective cover. Rear dimensions always require dismantling the lantern. On J11 (2019+) front lights are also accessible without removing the headlight, but the air duct may interfere - it needs to be disconnected (2 clips).

What are the longest lasting bulbs for Juke?

According to test results:

• Halogen: Philips LongLife EcoVision - up to 4 years of service.
• LED: Morimoto XB LED or Diode Dynamics SL1 - up to 50,000 hours.

However, durability depends on operating conditions. In regions with frequent temperature changes (for example, Siberia), even original lamps last 2 times less.