Rear bumper Nissan Terrano 2018 is not just an element of the exterior, but a key component of the safety and functionality of the car. It protects the body from mechanical damage, absorbs energy during minor collisions and serves as the basis for mounting lights, parking sensors and a towing device. However, even with careful use, the bumper can suffer from an accident, corrosion or natural wear and tear. In this article we will look at everything the owner needs to know. Terrano 2018: from the selection of original and non-original spare parts to step-by-step instructions for replacement and painting nuances.

Bumper Feature Terrano this model year - its integration with the active safety system. For example, in some trim levels radars for the system are located here Rear Cross Traffic Alert (rear cross traffic warning). This means that when replacing, it is important not only to select a compatible part, but also to connect the electronics correctly so as not to lose the functionality of the driver assistants. Next, you will learn how to avoid common mistakes and save on repairs without compromising safety.

Original articles and compatibility with other models Nissan

Original rear bumper for Nissan Terrano 2018 model supplied under article number 62610-4M000 (for version without rear view camera) and 62610-4M001 (with a hole for the camera). These parts are manufactured in factories Nissan in India and Thailand, which affects their cost and delivery time. Important: bumpers for Terrano pre-restyling (2014–2017) and restyling (2018+) versions not interchangeable due to changes in shape and fastenings.

If you are looking for analogues, pay attention to bumpers from Renault Duster second generation (2018–present) - they have a similar design, but require modification of the fastenings. Parts from Nissan Kicks (article 62610-4M010), but only for versions without parking sensors. The table below shows the key items and their features:

Article Model Features Average price, ₽
62610-4M000 Nissan Terrano 2018+ Without a hole for the camera, with mounts for parking sensors 18 000–22 000
62610-4M001 Nissan Terrano 2018+ With a hole for the camera, compatible with the system Around View Monitor 20 000–25 000
62610-4M010 Nissan Kicks 2018+ Requires modification of fastenings, there are no holes for sensors 15 000–18 000
260602039R Renault Duster 2018+ Suitable for versions without camera only, width adjustment required 14 000–17 000

When buying a used bumper, pay attention to the condition fastening points (they often rust) and integrity plastic embedded elements - their damage may make the part unsuitable for installation. Also check availability manufacturer's stamps (usually on the inside) is a guarantee of originality.

⚠️ Attention: Bumpers from Dacia Duster (European version) not suitable for Terrano due to different safety standards and light fixtures.

How to choose a non-original bumper: pros and cons of analogues

Non-original bumpers for Nissan Terrano 2018 are divided into three categories: OEM analogues (manufactured in the same factories as the originals, but without the logo Nissan), aftermarket (from third party manufacturers) and replicas (low quality copies). The first two options may be 30–50% more profitable than the original, but require careful selection.

Among the trusted brands:

  • 🔹 Febi (Germany) - OEM quality, article number 32316, price ~16,000 ₽. Suitable for versions with parking sensors.
  • 🔹 Hella (Türkiye) - good geometry, but plastic is less resistant to UV radiation. Article 8ZL 355 009-561.
  • 🔹 TSN (Russia) - a budget option (~12,000 ₽), but often requires adjustment to the fasteners.
  • 🔹 Depo (Taiwan) - average quality, article number 335-19221-100, suitable for versions without camera.

The main disadvantage of analogues is possible problems with alignment of fastenings (holes for lights or sensors may not match). Also some parts come without reinforcing beam, which reduces protection upon impact. Before purchasing, be sure to check with 3D model of the bumper (it can be found on spare parts websites by car VIN code).

📊 Which bumper would you prefer for your Terrano?
  • Original (Nissan)
  • OEM analogue (Febi, Hella)
  • Budget aftermarket (TSN, Depo)
  • Used original
  • I don't know
⚠️ Attention: Bumpers from Chinese manufacturers (for example, Keenon or WingAuto) often have distorted geometry. This may cause installation problems rear parking sensors or tow hook.

Step-by-step instructions for replacing the rear bumper

Replacing the bumper with Nissan Terrano 2018 requires a minimum set of tools: 10 and 12 socket wrenches, a screwdriver with a Phillips bit, plastic mounting spatulas and an assistant (the bumper is heavy and difficult to hold on your own). The whole process will take 1.5–2 hours if you have experience.

Sequence of actions:

  1. Disconnect the negative battery terminal to avoid short circuits when working on electronics.
  2. Remove the rear lights: unscrew the two bolts securing each light (10mm socket wrench) and disconnect the power connectors.
  3. Remove the fender liners: they are attached to 4–5 screws and 2 plastic pistons. Be careful - the caps break easily.
  4. Unscrew the bolts securing the bumper to the side members (2 on each side, 12 key) and two bolts at the bottom (under the bumper).
  5. Carefully disconnect the bumper, first disconnecting the parking sensor connectors (if any).
  6. Install the new bumper in the reverse order, making sure that all the gaps between it and the body are the same (tolerance is no more than 3 mm).

The holes for the parking sensors match the original|

The lamp mounts are not deformed|

There are no cracks or signs of repair on the inside|

All plastic embedded elements are in place|

Connectors for electronics (camera, sensors) are connected correctly-->

Pay special attention adjusting parking sensors. After installing the bumper, they need to be calibrated using a diagnostic scanner (for example, Launch X431). If this is not done, the system will generate false positives. Also check the work rear camera — its connector often oxidizes, which leads to interference on the screen.

💡

If the bumper does not come with holes for parking sensors, you can drill them yourself using a cardboard template. The main thing is to maintain the distance between the centers of the holes (usually 30–32 mm for Terrano).

Bumper repair: when is it more profitable than replacement?

A damaged bumper does not always need to be replaced. If the cracks do not affect fastening points And reinforcing beam, it can be repaired. The average cost of repairs (plastic welding + painting) in Moscow costs 8,000–12,000 rubles, which is 2 times cheaper than a new original bumper.

Types of repairs and their features:

  • 🔧 Welding plastic — suitable for cracks up to 20 cm long. A special polypropylene rod (for Terrano - brand PP/EPDM). Important: welding must be carried out at a temperature not lower than +15°C, otherwise the seam will be fragile.
  • 🎨 Local painting - if only the paintwork is damaged. Used body color base (color code for Terrano 2018 — KAD for metallic gray, QAB for black).
  • 🔨 Glass fiber reinforcement - used for major damage. Disadvantage: increases the weight of the bumper and may affect the operation of parking sensors.
  • 🔥 Thermoforming - restoration of shape with hot air. Effective for dents, but not suitable for cracks.

Critical point: if the bumper received a blow in the area of ​​attachment to the side member, it must be replaced. Even after repair, such a part will not provide adequate protection in the next accident.

What happens if the cracks are not repaired?

Unclosed cracks accumulate moisture, which leads to corrosion of the metal bumper mounts. Over time this can cause:

- Peeling of plastic from the body when driving (especially at high speeds).

- Damage to parking sensor wiring due to vibration.

- Water getting into the lamp unit, which leads to their failure (the cost of a new lamp is from 7,000 ₽).

Painting a bumper: technologies and common mistakes

Rear bumper painting Nissan Terrano 2018 requires adherence to technology, otherwise the paint will begin to peel off in 6–12 months. Main stages:

  1. Degreasing - use Anti-Silicone (for example, from 3M). Never use solvent 646 - it destroys the plastic.
  2. Primer - for plastic you need a special primer with a plasticizer (for example, PPG DP40). Apply in 2 layers with drying time of 15 minutes between them.
  3. Painting - used base enamel (color selected by code) + varnish (for Terrano recommended Sikkens Autoclear). The paint is applied in 3 layers with interlayer drying for 10 minutes.
  4. Polishing — 24 hours after painting the surface is polished with paste 3M Finesse-it to remove shagreen.

Typical mistakes when painting:

  • ❌ Applying paint without a primer leads to peeling after 3-6 months.
  • ❌ Drying at temperatures below +20°C - the varnish does not polymerize completely, remains soft.
  • ❌ Using cheap paint without a UV filter - the bumper will burn out in a year.

The average cost of painting in the service is 6,000–10,000 rubles (excluding materials). If you paint yourself, buy materials with a reserve: for the bumper Terrano it takes ~300 ml of base and 200 ml of varnish.

💡

For a perfect color match, order paint tinting based on your vehicle's VIN code. Even the original color code (eg. KAD) may have shades depending on the batch of paint at the factory.

Towing device and bumper: what you need to know

If you plan to install tow bar on Nissan Terrano 2018, please note that the original bumper does not have a standard hole for it. You will either have to cut out part of the plastic, or buy a bumper with a ready-made hole (for example, article number 62610-4M002, but it is rarely found on sale).

Compatible towbars:

  • 🔌 Bosal 11-04BR — removable, with electrics for a 13-pin socket, price ~12,000 ₽.
  • 🔌 Westfalia 365556501020 — stationary, with increased load capacity (up to 2 tons), ~15,000 ₽.
  • 🔌 AvtoS 110-0021-01 — a budget option (~8,000 ₽), but requires modification of the fastenings.

When installing a tow bar, be sure to:

  1. Check integrity reinforcing beam bumper - it must withstand a load of up to 75 kg (for Terrano with a diesel engine - up to 100 kg).
  2. Connect the electrics via matching block (For example, Tralert CAN-Bus), so as not to burn out the on-board network.
  3. Adjust tow ball height - it should be at a level of 350–420 mm from the ground (for Terrano optimally 380 mm).
⚠️ Attention: If you install a towbar on a bumper without a reinforcing beam (for example, on a cheap aftermarket analogue), when towing a trailer weighing more than 500 kg, the plastic may crack and the fastenings may become deformed.

Where to buy spare parts: verified suppliers and prices

Rear bumper prices for Nissan Terrano 2018 vary greatly by region and supplier. Below are the current offers for June 2026:

Supplier Part type Price, ₽ Delivery time Features
Exist.ru Original (62610-4M000) 19 500 3–5 days 1 year warranty, authenticated
Emex.ru OEM equivalent (Febi 32316) 15 800 2–4 days Free delivery for orders over RUB 10,000
AvtoALL Aftermarket (TSN) 11 200 1–3 days Frequent promotions, but high percentage of defects
Avito (used) Original used 8 000–12 000 1–2 days Risk of buying a broken or painted bumper
AliExpress Replica (Keenon) 9 500 20–30 days No guarantee, geometry often does not match

When purchasing a used bumper, be sure to check:

  • 🔍 Condition fastening points (there should be no rust or deformation).
  • 🔍 Integrity plastic mortgages (they should not be cracked).
  • 🔍 Availability manufacturer's stamps (on the original there is a logo Nissan and batch number).
  • 🔍 Compatible with your equipment (for example, a bumper with a camera will not be suitable for the version without it).

If you buy a bumper abroad (for example, eBay or AliExpress), please note that problems may arise with customs clearance (duty - 15–20% of the cost) and guarantee (most Chinese sellers do not refund money for defects).

FAQ: Frequently asked questions about the rear bumper Nissan Terrano 2018

Is it possible to install a bumper from Renault Duster on Terrano 2018 without modifications?

No, bumpers are not interchangeable without 修改. Main differences:

  • Different mounts for rear lights (on Duster they are already 10 mm).
  • Lack of holes for parking sensors (if your vehicle has them) Terrano).
  • Different shape of the bottom edge (on Terrano it is more curved for better aerodynamics).

Installation will require trimming the plastic and re-drilling the fasteners, which can weaken the structure.

What glue is best to use to repair cracks on a bumper?

For Nissan Terrano 2018 (plastic PP/EPDM) fit:

  • 3M Scotch-Weld DP8005 — two-component epoxy adhesive, withstands up to 70 kg/cm².
  • Loctite 3430 - quick-drying (15 minutes), but requires pre-treatment of the plastic with a primer.
  • Würth 892.1 — specialized for bumpers, resistant to vibrations.

Do not use superglue (cyanoacrylate) - it becomes brittle at low temperatures.

Do I need to paint a new bumper if it comes with primer?

Yes, definitely. Bumpers in primer do not have protection from UV rays and mechanical damage. If you leave it as is:

  • After 3–6 months, the soil will begin to turn yellow and peel.
  • The plastic will become brittle due to oxidation.
  • If moisture gets into microcracks, corrosion of metal fasteners will begin.

Minimal processing: application of 2 layers of base paint + varnish.

Is it possible to drive without a rear bumper?

Technically yes, but this illegal and dangerous. According to the Russian Federation Traffic Regulations (clause 7.18), the absence of a bumper is considered malfunction, for which a fine of 500 ₽ is provided (Article 12.5 of the Administrative Code). In addition:

  • There is no protection of the body from stones and dirt (risk of sill corrosion).
  • Parking sensors and camera (if any) do not work.
  • In the event of an accident, the insurance company may refuse to pay, citing modifications to the vehicle.

If the bumper is removed temporarily (for example, for repairs), cover the open fasteners with tape to prevent water from getting into the electrical wiring.

How can I check if they are selling me an original bumper?

Original bumper Nissan has the following characteristics:

  • 🔹 Logo Nissan on the inside (embossed, not sticker).
  • 🔹 Article (For example, 62610-4M000) is engraved on the plastic.
  • 🔹 Barcode with the batch number (can be checked through the service Nissan Parts).
  • 🔹 Embedded elements made of metal (on replicas they are plastic).
  • 🔹 Packaging — the original comes in a branded box with a hologram.

If the seller refuses to provide a photo of these parts, it is most likely a fake.