Installing a rear view camera on Nissan Almera G15 - a task that even a beginner can handle with the right approach. This modification not only makes parking easier, but also increases safety: according to statistics, 30% of road accidents in urban conditions occur when reversing. Unlike older models Nissan (For example, Qashqai or X-Trail), where the camera often comes as standard, owners Almera G15 (2012–2019) you have to modify the car yourself.

In this guide, we will go through all the stages - from choosing a camera to integrating it with a standard radio or after-market system. We will pay special attention typical mistakes, which lead to flickering of the image, incorrect operation of the reverse trigger or equipment failure. For example, many people forget about the need to use a 12V voltage stabilizer for cameras with backlight, which leads to malfunctions in headlights or alarms.

Choosing a rear view camera: which models are suitable for Almera G15

The first step is to decide on the type of camera. For Nissan Almera G15 Three options are suitable:

  • 🔹 Universal cameras on a bracket (attached above the license plate). Suitable for any body, but require drilling holes for wires.
  • 🔹 Built-in cameras into the trunk handle. The best choice for Almera G15, as they do not spoil the appearance and are protected from dirt.
  • 🔹 Cameras in the license plate frame. The simplest installation, but the image may be obscured by dirt or snow.

Among the tested models for Almera G15 stand out: Blackview BV-CM12 (built-in, viewing angle 170°, night shooting), Parkmaster 700TVL (high definition, but requires a separate power supply) and Rear View Safety RVS-062713 (heated for cold climates). Pay attention to the connectors: for the standard radio Nissan (if it has a screen) you will need a camera with RCA- an output for post-market systems - perhaps AHD or CVBS.

Key parameters when choosing:

  • 📏 Viewing angle: optimal 150–170°. Less - blind spots, more - distortion at the edges.
  • 🌙 Night photography: Look for models with IR illumination (for example, 6-12 diodes).
  • 🔌 Connection type: for Almera G15 with a standard radio without a screen, a separate monitor will be required.
  • 🛡️ Moisture protection: class IP67 or higher (for example, IP69K for pressure washing).
📊 What camera are you planning to install?
  • Universal on bracket
  • Built into the trunk handle
  • In license plate frame
  • I haven't decided yet

Required tools and materials

Before starting work, prepare:

Category Tools/materials Notes
Basic Tools Phillips screwdriver (PH2), flat screwdriver, socket wrenches (10 mm, 12 mm), plastic scrapers for removing trim For Almera G15 No special keys are needed - a standard set is enough.
Electrics Multimeter, soldering iron (power 40–60 W), heat shrink tube, electrical tape, female-male terminals, 12V relay (if needed) To check the voltage on the reverse wires, use a multimeter in DC 20V.
Cable laying Corrugated tube (Ø8–10 mm), ties, silicone sealant, double-sided tape For Almera G15 The optimal cable route is through the left side of the trunk and under the interior trim.
Additionally Flashlight, telescopic handle mirror, alcohol wipes (for cleaning contacts) A mirror will help you check the cable routing under the car.

If you have a radio without a screen (for example, the basic version Almera G15 with audio system Nissan CD/RDS), additionally you will need:

  • 📺 Monitor in the rear view mirror (for example, Auto-Vox M1) or a separate display on the dashboard.
  • 🔌 Adapter for connecting the camera to the cigarette lighter (if there is no standard connector RCA).
⚠️ Attention: Do not use cheap Chinese cameras from Aliexpress without certification ECE R10. They may interfere with the on-board network Almera G15, especially when working with the CAN bus (for example, when activating parking sensors).

Rear view camera connection diagram

The electrical connection diagram depends on the type of radio and camera. Let's consider two options:

1. Connection to a standard radio with a screen (for example, Nissan Connect):

  • 🔴 Camera power: connect +12V to the reverse wire (orange-black wire in the trunk harness, contact B10 in the fuse box).
  • 🔵 Weight: to the body next to the camera (clean the metal until shiny).
  • 🟡 Video signal: RCA-cable to the corresponding connector of the radio (usually A/V IN).
  • 🟣 Management: Connect the trigger wire (most often purple) to the reverse wire for automatic activation.

2. Connection to an aftermarket radio (for example, Pioneer AVH-X5800):

  • Use the connector CAMERA IN on the back of the radio.
  • If the radio does not support automatic shifting, you will need a relay to break the circuit when reverse gear is engaged.

Connection diagram for Almera G15 with basic radio (without screen):



Камера


│


├── +12В → Провод заднего хода (оранжево-черный, контакт B10)


├── GND → Кузов (зачищенный металл)


└── RCA → Монитор в зеркало/на торпедо

Test the reverse wire with a multimeter (it should be +12V when the gear is engaged)

Clean contacts with alcohol

Lay the cable in a corrugation along the standard wiring

Insulate all twists with heat shrink -->

⚠️ Attention: On Almera G15 with the system Around View Monitor (optional for top-end configurations) you cannot connect a third-party camera directly - this will lead to an error C1609 in the control unit. In this case, you need a signal emulator or radio firmware.

Step-by-step instructions for installing the camera

Let's look at the installation using the example of a built-in camera in the trunk handle Blackview BV-CM12:

Step 1. Removing the trunk trim

  • Remove the two screws under the plastic cover in the trunk (use a socket wrench 10 mm).
  • Remove the plastic clips around the perimeter by prying them off with a spatula. Be careful - on Almera G15 they often break.
  • Disconnect the trunk light connectors (white and black wires).

Step 2: Camera Installation

  • Drill a hole in the trunk handle with a diameter of 20 mm (use a metal drill).
  • Insert the camera into the hole and secure it on the back with a nut (included in the kit).
  • Apply silicone sealant around the edge of the chamber to protect against moisture.

Step 3. Cable installation

  • Route the cable from the camera along the left side of the trunk, securing it with zip ties to the standard wiring.
  • In the cabin, route the cable under the sill trim and along the center console to the radio.
  • For Almera G15 the optimal route is through the rubber seal between the trunk and the passenger compartment (next to the door hinges).

Step 4. Connecting to the radio

  • Connect RCA-camera connector to the corresponding radio input.
  • Power cord (+12V) connect to the reverse wire (check with a multimeter!).
  • Secure all connections with heat shrink tubing.
💡

On Almera G15 with radio Nissan Connect After connecting the camera, you need to reset the multimedia settings: hold down the button POWER for 10 seconds, then reboot the system through the menu Settings → System → Reboot.

Setting up the camera and radio

After installation, you need to configure the image parameters:

For standard radio Nissan Connect:

  1. Go to Settings → Camera → Rear view mode.
  2. Activate the option Automatic switching on.
  3. Adjust brightness and contrast in the menu Image Settings.
  4. If the image is upside down, enable the option Mirror Mode (Mirror mode).

For aftermarket radios (for example, Pioneer or JVC):

  • On the menu Camera Settings select connection type (RCA or AHD).
  • Set up parking lines: on Almera G15 optimal parameters - width 1.7 m, length 4.5 m.
  • If the camera supports Parking Guidelines, activate dynamic lines (they change when you turn the steering wheel).

To calibrate parking lines:

  1. Park the machine on a level surface.
  2. Measure the distance from the bumper to the obstacle (for example, 1 m).
  3. In the radio menu, adjust the scale of the lines so that they coincide with the real distance.
How to reset camera error on Almera G15?

If the indicator on the dashboard lights up after installation Check Camera, follow these steps:

1. Disconnect the negative terminal of the battery for 10 minutes.

2. Reconnect and turn on the ignition (without starting the engine).

3. Shift into reverse three times at 5 second intervals.

4. The error should be reset. If not, diagnostics with a scanner is required (for example, Launch X431).

Common mistakes and how to avoid them

Even with careful installation, owners Almera G15 are facing problems. Let's look at the most common ones:

  • 🔋 The camera does not turn on in reverse gear:

    Cause: Incorrect trigger wire connection. Check that the camera wire (usually purple) is connected to the reverse wire (orange/black in the trunk harness). On Almera G15 this wire goes through the fuse box F36 (10A).

  • 📺 Flickering or noisy image:

    Cause: poor ground contact or insufficient voltage. Make sure the camera ground is connected to cleared body metal, not plastic or rust. If the problem persists, add a voltage stabilizer 12V → 12V (For example, LM2596).

  • 🔄 Image is upside down or mirrored:

    Reason: incorrect radio settings. In the camera menu, activate the options Flip (coup) and/or Mirror (mirror). On some radios (for example, Sony XAV-AX100) these settings are hidden in the engineering menu (entrance by code 12345).

  • 🚨 The camera indicator on the dashboard is constantly on:

    Cause: Short circuit in the trigger wire. Check the circuit with a multimeter in calls. On Almera G15 this wire should not come into contact with +12V constantly.

⚠️ Attention: If after installing the camera the standard parking sensors stop working Almera G15, check the fuse F22 (15A) in the block under the hood. The camera could create a load on the overall sensor circuit.

Additional improvements: parking sensors, dynamic lines, video recording

To make your parking system even more convenient, consider the following modifications:

  • 🎯 Integration with parking sensors:

    If on your Almera G15 parking sensors have already been installed (for example, Parkmaster 4), connect them to the radio via CAN bus or separate entrance PDC. This will allow you to display the distance to obstacles directly on the camera screen.

  • 📊 Dynamic parking lines:

    Camera models with a gyroscope (for example, Boyo VTL375) draw lines that change when you turn the steering wheel. To do this, you need to connect the camera to CAN bus via an adapter (for example, iDataLink Maestro).

  • 🎥 DVR with rear view camera:

    Devices like BlackVue DR750S-2CH Allows you to record video from the rear camera to a memory card. For Almera G15 You will need an additional power supply (for example, BlackVue B-124X), since standard wiring is not designed for constant load.

  • 🔊 Voice prompts:

    Some radios (for example, Kenwood DMX7017DAB) support voice notifications about the distance to an obstacle. To do this you need to activate the option Voice Guidance in the parking menu.

💡

On Almera G15 with automatic transmission (variator Jatco JF015E) dynamic parking lines must take into account the delay in reverse gear engagement (about 1 second). Adjust the trigger delay in the radio accordingly.

FAQ: Frequently asked questions about installing a camera on Almera G15

Is it possible to install a rear view camera on an Almera G15 with a basic radio without a screen?

Yes, but you will need a separate monitor. Optimal options:

  • 🔄 Rear view mirror with screen (For example, Auto-Vox M1). Replaces the standard mirror, connects to the cigarette lighter.
  • 📱 Monitor on the dashboard (For example, Pumpkin 7"). Attached with double-sided tape or bracket.

To connect, use the following diagram: camera → monitor → power from the reverse wire.

Which fuse is responsible for reverse gear on Almera G15?

The reverse circuit is controlled by a fuse F36 (10A) in the fuse box under the hood. Also check the relay K3 (reverse relay), which is located in the interior unit behind the glove compartment. If the fuse blows after installing the camera, it means there is a short circuit in the power cable.

Which rear view camera is better to choose for the Almera G15 in terms of price/quality ratio?

Optimal models priced up to 5,000 rubles:

Model Pros Cons
Blackview BV-CM12 Built-in, 170° angle, night shooting, IP69K Requires drilling of trunk handle
Parkmaster 700TVL High definition, suitable for Full HD monitors You need to buy an additional power supply
Rear View Safety RVS-062713 Heated, frost-resistant, durable housing More expensive than analogues (about 6,000 rubles)

For Almera G15 with radio Nissan Connect it is better to choose a camera with resolution 600–700 TVL — higher resolutions are not supported.

How to check if the camera is working properly after installation?

Run the test:

  1. Engage reverse gear and the camera should start automatically.
  2. Check the image clarity in the dark (if there is IR illumination).
  3. Measure the actual distance to the obstacle (for example, 1 m) and compare with the lines on the screen.
  4. Check if the image flickers when the headlights or alarm are turned on.

If the camera is unstable, check:

  • The quality of the mass (must be ≤ 0.5 ohm when calling).
  • The voltage on the power wire (should be 11.8–12.5V).
  • Integrity RCA-cable (are there any fractures).
Is it possible to connect a rear view camera to the standard display on the Almera G15 dashboard?

No, the standard display between the speedometer and tachometer (the so-called MFD) does not support video output. It is intended only to display data from the on-board computer (fuel consumption, temperature, etc.). To display the image from the camera you will need:

  • Replace the radio with a model with a screen (for example, Pioneer SPH-DA120).
  • Install a separate monitor (in the mirror or on the dashboard).

Exception - Almera G15 included TEKNA with the system Around View Monitor, but even in this case, you will need a signal emulator to connect a third-party camera.