Nissan March is a compact hatchback that has gained popularity due to its efficiency and maneuverability. However, when replacing rims, owners often face the question: what drill bit is suitable for this model?? Error in choosing parameters PCD, ET or DIA can lead to vibrations, accelerated wear of the wheel bearings, or even the inability to install the disc. In this article we will look at all the nuances of drilling for Nissan March K13 (2010–2023) and K12 (2002–2010), and also give practical advice on selecting disks.

Feature March — its light weight and compact dimensions, which imposes restrictions on the choice of disks. For example, too much overhang (ET) can lead to friction between the disc and the caliper, and incorrect PCD will make the fastening unreliable. We analyzed factory parameters, manufacturer data and owner reviews to create an up-to-date compatibility table and avoid common mistakes.

What is wheel drilling and why is it important for Nissan March

Drilling (or bolt pattern) is a set of parameters that determine how the disc is attached to the vehicle hub. For Nissan March Three values are critical:

  • 🔧 PCD (Pitch Circle Diameter) - the diameter of the circle on which the mounting holes are located. For March this is 4×100 (4 holes, diameter 100 mm).
  • 📏 ET (Offset) — disc offset, measured in millimeters. Shows how much the disc is “recessed” or “protrudes” relative to the hub.
  • ⚙️ DIA (Central Hole) — diameter of the hole for the hub. For March K13 this is 66.1 mm.

If at least one of these parameters does not match, the disk either will not fit on the hub or will be installed skewed. For example, if incorrect PCD the bolts will not be able to tighten evenly, resulting in steering wheel wobble at speeds above 80 km/h. And the error in ET can cause premature wear of the suspension or the disc touching the arch when turning.

Owners March They often ask: is it possible to install disks from other models? Nissan? The answer is yes, but only if the parameters match. For example, disks from Nissan Micra K13 will fit, since they have identical drilling, but from Nissan Juke - no (he has PCD 5×114.3).

📊 What wheels are you planning to install on your Nissan March?
  • Steel
  • Cast
  • Forged
  • Tuning
  • I haven't decided yet

Factory drilling parameters for Nissan March K12 and K13

Drilling parameters depend on the generation and year of manufacture March. Below is a table with official manufacturer data:

Generation Years of manufacture PCD ET (departure) DIA (hub) Mounting thread
Nissan March K12 2002–2010 4×100 35–45 mm 66.1 mm M12×1.25
Nissan March K13 (dorestyle) 2010–2017 4×100 35–45 mm 66.1 mm M12×1.25
Nissan March K13 (restyle) 2017–2023 4×100 38–45 mm 66.1 mm M12×1.25

Please note: departure (ET) for the restyled version K13 changed a little. This is due to modifications to the suspension and body. If you install discs with offset ET 35 on Restyle, they can protrude beyond the arch, which will lead to friction when the car is fully loaded.

⚠️ Attention: Discs with offset ET 45 and more can worsen handling at high speeds due to a shift in the center of gravity of the wheel.

It is also worth considering that some versions March (for example, with an engine HR12DE) have reinforced suspension, which allows the use of wheels with a shorter offset. However, this requires additional testing at the wheel alignment stand.

Compatibility of Nissan March wheels with other models

If you are looking for alternative wheels, you can consider models from other cars Nissan or Renault (since March K13 built on a platform Renault-Nissan B). Below is a list of compatible models:

  • 🚗 Nissan Micra K13 (2010–2023) - full compatibility in all respects.
  • 🚗 Renault Clio IV (2012–2019) - same PCD 4×100, but verification required ET And DIA.
  • 🚗 Dacia Sandero II — suitable, but may require a spacer to adjust the offset.
  • 🚗 Suzuki Swift III (2010–2017) - same PCD, but the central hole (DIA 54.1 mm) less, centering rings will be required.

When choosing disks from other models, be sure to consider:

  1. Coincidence PCD 4×100 - this is the main criterion.
  2. Central hole diameter (DIA). If it is greater than March, the disc will not fit tightly on the hub, which will lead to runout. If less, you will need centering rings.
  3. Departure (ET). Permissible deviation is ±5 mm from the factory value.
⚠️ Attention: Discs from Nissan Juke, Qashqai or X-Trail not suitable for March due to various PCD (5×114.3) and more DIA.

If you plan to install wheels with a non-standard offset, we recommend using spacers. However, this requires professional installation, as incorrectly selected spacers can lead to destruction of wheel bearings.

Does PCD match (4×100)|

Is the center hole diameter (66.1mm) suitable?

Overhang (ET) 35-45mm|

Bolt thread (M12×1.25) compatible with your hub|

Are there any traces of corrosion on the seating surface of the disc-->

How to measure drilling parameters yourself

If you are not sure about the parameters of your disks or are buying a used set, you can measure the drilling yourself. You will need:

  • 📐 Caliper or ruler.
  • 🔩 Wheel bolt wrench.
  • 📝 Paper and pen for notes.

PCD Measurement:

  1. Remove the disc from the car.
  2. Measure the distance between the centers of two adjacent holes (for example, L).
  3. For 4 holes PCD = L × 1.414 (since 4 bolts form a square).

ET (departure) measurement:

  1. Place the disc face down on a flat surface.
  2. Measure the distance from the plane of contact of the disc to the hub to the edge of the rim (A).
  3. Turn the disk over and measure the distance from the contact plane to the opposite edge (B).
  4. Departure ET = (A + B)/2 – B.

DIA measurement:

Simply measure the diameter of the center hole with a caliper.

If you don’t have the tools, you can use online catalogs, where they will select compatible wheels based on the VIN code or car model. For example, on sites Alloy Wheels Direct or TyrePlus.

What to do if the PCD doesn't match?

If you made a mistake with PCD and have already bought the disks, there are two options:

1. Use eccentric bolts (for example, from Hubcentric), which compensate for the difference of 1–2 mm.

2. Selling the discs and buying the right ones is safer, since the eccentrics can weaken over time.

We do not recommend drilling new holes - this disrupts the structure of the metal and can lead to cracks.

Typical mistakes when choosing wheels for Nissan March

Even experienced car owners sometimes make mistakes when selecting wheels. Here are the most common:

  • 🔄 Ignoring crash (ET). Discs with ET 30 They may look stylish, but they will snag the calipers and increase stress on the wheel bearings.
  • 🕳️ Mismatch DIA. If the center hole is larger than 66.1 mm, the disc will not be centered on the hub, which will cause vibration.
  • 🔩 Incorrect bolt threads. Threaded bolts M12×1.5 (for example, from Toyota) are not suitable for March, where needed M12×1.25.
  • 🚗 Installing discs with the wrong diameter. For example, R15 instead of R14 may lead to contact with the fender liners.

One of the most dangerous mistakes is using universal spacers without taking into account the load. Spacers increase the offset, but if they are not designed for weight March, may become deformed on bumps. We also do not recommend installing disks with ET 0 or negative offset - this greatly impairs handling on a small hatchback.

Another problem is purchasing replicas of famous brands (For example, BBS or Enkei). Such discs often have inaccurate geometry, which leads to imbalance. Before purchasing, check the seller's reviews and quality certificates.

💡

If you buy used wheels, be sure to check them for runout. Place the disk on a flat surface and spin it - if there is play or it swings like a figure eight, you cannot take such a disk.

Recommendations for selecting wheels: cast, forged or steel?

The choice of disc material depends on your goals:

Disc type Pros Cons Recommendations for March
Steel Cheap, durable, easy to repair Heavy, limited design Suitable for winter tires or budget use
Cast (aluminum) Lightweight, wide range of designs Dear ones, they may crack if hit hard. The best option for city driving
Forged The most durable and lightest Very expensive, limited range Suitable for tuning or sports driving

For Nissan March we recommend:

  • 🌨️ For winter - steel wheels with caps. They are cheaper and don’t mind getting scratched in the snow.
  • 🏙️ For the city - alloy wheels with departure ET 38–42. They reduce the load on the suspension and improve dynamics.
  • 🏁 For tuning - forged wheels with minimal weight, but only if the budget allows.

When choosing alloy wheels, pay attention to certification. Discs without markings JWL or VIA may not withstand the load. Also check maximum load (for March enough 600–650 kg per disc).

💡

For Nissan March K13, the optimal disc offset is ET 38–42 mm. This strikes a balance between controllability and safety.

Where to buy wheels for Nissan March: proven options

When purchasing discs for March It is important to choose a reliable seller. Here are a few proven options:

  • 🛒 Official dealers Nissan — guarantee of original spare parts, but prices are higher than the market.
  • 🌍 Online stores:
    • Kolesa-darom.ru - large selection of used wheels.
    • AlloyWheelsDirect — cast and forged wheels with delivery.
    • Avito or Drom - you can find good deals, but careful checking is required.
  • 🏬 Local tire shops — often sell used or new wheels at wholesale prices.

When purchasing used disks, be sure to:

  1. Check for cracks and dents.
  2. Make sure there are no signs of welding or repairs.
  3. Ask the seller to show the disc on the balancing machine.

If you buy new wheels, pay attention to the brands:

  • 💰 Budget: K&K, Replica, Alutec.
  • 🏆 Premium: BBS, Enkei, OZ Racing.
  • 🔧 For tuning: Work, SSR, Rays.

⚠️ Attention: Discs from Chinese brands without certification (for example, Yato or Autostrada) may have inaccurate geometry. Before purchasing, read reviews on Drive2 or forums.

FAQ: Frequently asked questions about drilling Nissan March wheels

Is it possible to install 5x114.3 wheels on a Nissan March?

No, this is impossible without serious modifications. Nissan March has a drill bit 4×100, and 5×114.3 is the standard for Nissan Qashqai, X-Trail and other large models. An attempt to adapt such discs will lead to uneven tightening of the bolts and danger on the road.

Which Renault wheels are suitable for the March K13?

From Renault Clio IV or Captur I discs with parameters are suitable PCD 4×100, ET 35–45 And DIA 66.1 mm. However, some models Renault the central hole may be 60.1 mm - in this case, centering rings will be required.

What happens if you install wheels with an offset of ET 30?

Discs with offset ET 30 protrude strongly outward, which will lead to:

  • Friction against the caliper or arch when turning.
  • Increased load on wheel bearings.
  • Deterioration in handling (the car will “yaw” at speed).

The permissible deviation from the factory offset is no more than ±5 mm.

Do I need to balance the disks after installation?

Yes, balancing is required! Even new rims can be unbalanced due to uneven weight distribution. Unbalanced wheels lead to:

  • Steering wheel vibrations at speed 90–110 km/h.
  • Accelerated wear of the suspension.
  • Uneven tire wear.

Balancing needs to be done every 10–15 thousand km or after a strong impact (for example, falling into a hole).

Can I use wheel spacers on March?

Spacers can be used, but with caution:

  • The thickness of the spacer should not exceed 10–15 mm.
  • Spacers should be made of aluminum or steel, not plastic.
  • Be sure to use extended bolts of the appropriate length.

Incorrectly installed spacers can lead to wheel coming off while driving!