Door card (trimming) Nissan Almera Classic (body B10, 2006–2018) is a part that sooner or later has to be removed: whether it’s replacing a speaker, repairing a window regulator, or eliminating squeaks. It would seem like a simple operation, but without knowing the nuances you can break plastic clips, tear the casing or damage the electrical wiring. In this article - step-by-step analysis of the process taking into account typical mistakes, hidden fasteners and advice from auto electricians.

Feature Almera Classic — fragile pistons and non-obvious points of fixation of the casing. For example, many people forget about the fastening under the door handle or do not know how to properly disconnect the locking cable. We'll sort it out unique dismantling algorithm for this model, which minimizes the risk of damage and saves time. And at the end - an FAQ with answers to frequently asked questions, including finding analogue clips and ways to repair broken fasteners.

Preparing for dismantling: tools and precautions

Before you begin removing the door card, make sure you have everything you need. Minimum set of tools:

  • 🔧 Plastic puller or mediator (required! metal screwdrivers scratch plastic).
  • 🔩 Phillips screwdriver (usually PH2) for screws under the handle and speaker.
  • 📸 Phone for photographing the location of the clips (useful for reassembly).
  • 🧲 Magnet on the telescopic handle (so as not to lose the screws in the doorway).

Important: before work disconnect the negative terminal of the battery. This will prevent a short circuit if the wiring is accidentally touched. Also check if there are any foreign objects (bottles, documents) in the door - they may fall out when the trim is removed.

⚠️ Attention: If on your Almera Classic Electric windows are installed; lower the glass all the way before removing it. Otherwise, after removing the card, it may “fall” inside the door, and you will have to disassemble the mechanism to return the glass to the grooves.

Advice from the experts: if the clips have already broken before, buy a set of new ones in advance. Original articles for Nissan Almera Classic:

  • 🔹 Door trim clips - 77260-4M000 (pack of 10 pcs.).
  • 🔹 Speaker mounting pistons - 28541-31U00.
📊 Which door are you planning to dismantle?
  • Driver's license
  • Passenger front
  • Rear
  • I don't know yet

Step-by-step instructions: removing the door card without damage

Let's start with driver's door (the algorithm for the others is similar, but there are some nuances with the location of the clips). Follow the instructions strictly in order to avoid missing hidden fasteners.

  1. Remove the door handle trim trim. Use a puller to pry it from the inside (from the lock side) and pull it towards you. There is a screw hidden under the cover - unscrew it.
  2. Remove the mirror adjustment knob. It is attached with latches - pull it up with force. There may be another screw under the handle (depending on the configuration).
  3. Remove the screws under the speaker. Remove the speaker grille (it is latched), then unscrew 2-3 screws with a Phillips screwdriver.
  4. Disconnect the door lock cable. It is attached to the casing with a plastic clip - carefully pull it to the side.

Now let's move on to main clips. On Almera Classic There are usually 8–10 of them: 2–3 on each side and on the sides. Start removing the trim from bottom corner (from the driver’s feet), since there is less risk of damaging the plastic. Pry the card with the puller and pull it towards you - the clips should come out with a characteristic click.

Battery terminal disconnected|

Window fully down|

Photos of the location of the clips were taken|

Tools at hand|

The locking cable is disconnected-->

If the casing does not give way, do not use force! Most likely you missed a screw or clip. Check:

  • 🔍 Under the opening handle (common mistake!).
  • 🔍 At the bottom of the trim near the threshold (there may be a hidden piston there).
  • 🔍 Behind the speaker (sometimes an additional screw is hidden there).
⚠️ Attention: On models with electrical package (power windows, mirrors) there is a wiring harness running under the trim. Do not pull the card sharply upward - first disconnect the connectors! They are usually secured with plastic latches that need to be pressed down before removal.

Hidden fastenings and common mistakes: what beginners don’t know

Even experienced car owners sometimes overlook non-obvious fixation points door card Nissan Almera Classic. Here's what most often causes breakdowns:

Mounting location Common mistake How to avoid
Clip under the opening handle They are trying to remove the casing without unscrewing the screw under the trim Always check for a screw under the trim panel
Locking cable The cable breaks when the casing is removed abruptly Disconnect the cable lock before removing the card
Clips at the bottom of the trim They break the caps by pulling the card up Start removing the trim from the bottom corner
Wiring connectors They break the wires without disconnecting the connectors Check all electrical connections before removal

One more secret nuance: on some versions Almera Classic (for example, 2012–2014) installed under the casing additional sound amplifier (if the car is in a top configuration). It is attached to the metal of the door and can interfere with card removal. To dismantle it, unscrew 2 10 mm bolts.

If you hear a cracking sound when removing the trim - stop immediately! It's the clips that break. It’s better to spend an extra 5 minutes looking for a hidden fastener than to then go to the store for new caps.

💡

Before reassembling, lubricate the clips with silicone grease - this will make installation of the casing easier and extend the life of the plastic fasteners.

What to do if the clips or casing are broken?

Even with careful dismantling, the risk of damaging the plastic parts remains. Let's consider repair methods typical breakdowns:

1. Broken clips

If the piston is cracked but has not completely fallen apart, it can be temporarily restore:

  • 🔥 Heat the plastic with a hairdryer and connect the parts (lasts 1-2 months).
  • 💉 Glue the crack with superglue (for example, Loctite 406).
  • 🔄 Buy a repair kit of clips (see article above).

2. Cracks in the casing

Small cracks (up to 3 cm) can be repaired:

  • 🔥 With help soldering iron and plastic rods (method for experienced ones).
  • 🧴 Epoxy resin with reinforcing mesh (suitable for hard plastic).
  • 🎨 Cosmetic repair: putty and paint in the interior color.

3. Broken cables or wires

If the locking cable or wiring is broken:

  • 🔧 Cable is possible connect with a sleeve (but it’s better to replace the whole thing).
  • 🔌 Wires are soldered with heat shrink or connectors are used Wago.
⚠️ Attention: Do not use electrical tape to repair door wiring! Due to constant temperature changes and vibrations, it will quickly peel off, which can lead to a short circuit.
Where to buy spare parts for repairs?

The most reliable options:

1. Official Nissan dealers (parts warranty, but expensive).

2. Auto dismantling stores (for example, Avtorazborka-Nissan in Moscow or analogues in your city) are cheaper, but check the condition of the parts.

3. Online platforms: Exist.ru, Autodoc.ru, Emex.ru — there you can find original clips by article number.

4. Aliexpress (only for non-critical parts like clips) - cheap, but wait 2-3 weeks.

Reassembly: how to install the door card correctly

Putting the trim back together is often more difficult than removing it. Main rule: start from the top and gradually snap the clips around the perimeter. Here is a step-by-step algorithm:

  1. Check all connectors. Make sure the wiring is connected correctly (especially if you removed the speaker or window regulator).
  2. Install the locking cable. Its latch should click into place.
  3. Secure the trim to the top clips. Press gently until you hear a click.
  4. Fasten the screws. Start with the opening handle, then the speaker and mirror handle.
  5. Check the operation of the mechanisms. Open/close the door, raise/lower the window, turn on the music.

If after assembly the casing dangles or creaks, the reasons may be as follows:

  • 🔍 Not all clips are in place (check the bottom).
  • 🔍 The screws are not tightened (especially under the handle).
  • 🔍 Dirt has gotten between the trim and the metal of the door (wipe the surfaces).

To eliminate squeaks you can use anti-squeak gaskets (for example, from foam rubber) or treat contact surfaces silicone grease. Don't use WD-40 - it attracts dust!

💡

When reassembling, do not use force! If the trim does not fit into place, you have missed a fastener or installed the cable incorrectly.

Modifications and tuning: what can be done after removing the trim

Since you've removed the door card, why not upgrade it? Here are a few useful improvements for Nissan Almera Classic:

  • 🔊 Installing good speakers. Cheap "paper" speakers come from the factory. They can be replaced with Pioneer TS-A1676F or Alpine SXE-1725S (fit without modifications).
  • 💡 Door lighting. A 12V LED strip is glued under the trim to illuminate the legs or pocket. Connect to the lamp lamp wire.
  • 🔋 Noise insulation. Glue the door metal Bimastom or Splenom - this will reduce noise and improve the sound of the speakers.
  • 🔒 Additional blocking. It is possible to install a mechanical interlock (for example, "Cobra") to protect against theft.

If you are planning paint the trim (for example, in body color), use plastic paint (for example, Motip Plastik) and be sure to degrease the surface Antisilicon. For a matte effect, add to paint matte varnish.

For bass lovers: out the door Almera Classic can be installed subwoofer (For example, Pioneer TS-WX120A), but you will need to modify the mount and stretch the reinforcing wires. Be prepared to cut off some of the plastic trim.

Frequently asked questions (FAQ)

How many fastening clips are there on the door card of Nissan Almera Classic?

Usually on the front doors 8–10 clips (depending on the year of manufacture and configuration). There are fewer of them on the rear doors - 6–8 pieces. The exact quantity can be found by looking at the back of the skin after removal.

Is it possible to remove the trim without a puller?

Theoretically yes, but the risk of damaging the plastic is very high. If you don't have a puller, use plastic card (for example, a bank) or a screwdriver wrapped in electrical tape. The main thing is not to pry off the metal casing!

How to remove the trim if all the clips are broken?

If the clips are completely destroyed, you can temporarily fix the trim to self-tapping screws with press washer (for example 3.5x9.5 mm). But this is a short-lived solution - it is better to buy new pistons.

What should I do if the window lifter does not work after assembly?

Most likely, you forgot to connect the connector or pinched the wires. Remove the trim again and check:

  • Is the connector connected to the window lift motor?
  • Is the wiring harness broken (especially at the bend).
  • Is the fuse working? Almera Classic this is usually F30 (15A) in the cabin block).
Where in Moscow/St. Petersburg can you buy clips for Almera Classic?

In Moscow:

  • Auto disassembly on Dmitrovka (Butyrskaya St., 86) - original parts.
  • Exist.ru (m. Tushinskaya) - store with delivery.

In St. Petersburg:

  • Auto Parts on Bukharestskaya (Bukharestskaya st., 72).
  • Autodoc (m. Kupchino) - can be ordered online with pickup.

In the regions, search through Yandex.Market or Avito with the filter “spare parts for Nissan”.