Removing the rear seat of a Nissan Qashqai: instructions with photos and tips

Rear seat in Nissan Qashqai - a structure that at first glance seems monolithic, but upon closer examination is easily disassembled. Regardless of whether you plan interior cleaning, electrical wiring repair under the sofa or installing additional equipment (for example, a subwoofer or organizer), knowing how to properly remove the back row of seats will save time and nerves. In this article - step-by-step algorithm taking into account the features of the models J10 (2006–2013) and J11 (2013–2021) and unique nuances, which are not written about in standard manuals.

Important: the dismantling process takes from 15 to 40 minutes depending on the vehicle configuration. For example, in versions with heated seats or electrically adjustable backrest You will have to disconnect additional connectors, but in basic versions it is enough to remove 4 latches. We'll look at both scenarios and also tell you how to avoid common mistakes, such as damaged plastic latches or broken wiring.

Preparation: Tools and Safety Precautions

Before you get started, make sure you have on hand:

• 🔧 10 mm socket wrench (for unscrewing the fastening bolts in models with ISOFIX).
• 🔨 Plastic puller or flathead screwdriver (for prying up the fasteners).
• 📸 Smartphone - to photograph the location of wires and connectors.
• 🧤 Gloves (will protect your hands from sharp edges of metal and plastic).

Required disconnect the negative terminal of the batteryif you plan to work with electrical wiring. This will prevent short circuits if the contacts are accidentally connected. In models Qashqai J11 with the system NissanConnect After disconnecting the battery, you may need to reboot the multimedia - please take this into account in advance.

⚠️ Attention: Do not use excessive force when removing the plastic clips! In 80% of cases, seat breakdowns occur due to an attempt to “pull out” the latch by force. If the latch does not budge, check whether a hidden bolt has gone unnoticed (for example, under a decorative plug).

Step 1: Removing the rear seat cushion

Start at the front of the cushion (passenger legroom). In models Qashqai J10 And J11 fastening is carried out using two metal hooks, which fit into the grooves of the body. To release them:

1. Pull the pillow up and on yourself with moderate effort.
2. If the seat does not budge, check to see if the hook is caught in the carpet (a common problem in cars with thick carpet).
3. After releasing the front hooks, slide the cushion forward to release the rear clips from the slots.

In versions with reclining backrest 60/40 The pillow is divided into two parts. Remove them one by one, starting with the smaller (40%) section. Please note: there may be items under the pillow heating wires (in configurations Tekna or Acenta Premium) - do not pull the seat sharply so as not to break the contacts.

Step 2: Removing the rear seat back

The backrest is attached to the body using two bottom bolts (one on each side) and upper clamps (in models with seat belts). Algorithm of actions:

1. Unscrew the bolts with a socket wrench on 10 mm (in J10 they can be hidden under plastic plugs).
2. Loosen the seat belt fastening nuts (if they interfere with the removal of the backrest).
3. Gently pull the backrest up and on yourself, releasing the top latches.

In vehicles with the system ISOFIX additionally need to be disconnected fastening brackets child seats. They are located at the bottom of the backrest and are secured with bolts or plastic latches. Don't lose small parts — they are difficult to find on sale separately.

Model	Backrest mounting type	Number of bolts	Availability of ISOFIX
Qashqai J10 (2006–2013)	Bolts + latches	2	Optional
Qashqai J11 (2013–2021, basic)	Bolts + plastic clips	2	Standard
Qashqai J11 (2013–2021, Tekna)	Bolts + metal brackets	4 (including ISOFIX)	Yes

⚠️ Attention: B Qashqai J11 with panoramic roof, the rear seat backrest can be connected to lighting wiring salon Before removing, disconnect the connector located under the trim on the right (passenger's side).

Step 3: Disconnecting the electrical wiring (for heated versions)

If your Nissan Qashqai equipped heated rear seats, under the pillow you will find:

• 🔌 Two power connectors (on the pillow and back).
• 📶 Thermal sensor (on models with climate control).
• 🔄 fuse (located in the block under the rear parcel shelf).

To disconnect the wires:

1. Click on connector lock (usually black or gray).
2. Pull the connector straight at yourselfwithout pulling to the sides.
3. Cover exposed contacts with electrical tape to prevent oxidation.

In versions with seat ventilation (For example, Qashqai J11 2.0 dCi Tekna) will additionally need to be disabled air pipescoming from the compressor. They should not be bent - this will lead to rupture of the membranes.

Nuances for different configurations

The process for removing the rear seat may vary depending on the vehicle's equipment. Let's look at the key features:

1. Models with system Nissan Safety Shield (J11 2017+):

In these versions there is a sensor block for the system Rear Cross Traffic Alert. When dismantling:

• Disconnect the sensor connector (orange, marked B124).
• Do not drop the unit - it is calibrated when installed at the factory.

2. Cars with hybrid installation (J11 1.6 DIG-T Hybrid):

Under the rear seat are laid high voltage cables (orange color). They must not be damaged or bent! Before work:

• Make sure the car off (key in position LOCK).
• Use dielectric gloves.

3. Versions with third row of seats (Qashqai +2):

In these modifications, the rear sofa consists of three sections. The middle part is removed last, since it is attached to body frame additional bolts.

What to do if the latch is stuck?

If the plastic latch does not release, try treating it with silicone lubricant (for example, WD-40 Specialist). Do not use mineral-based oils - they will corrode the plastic. If the latch is broken, it can be replaced with an analogue from Renault Koleos (catalog number 820084064R).

Reassembly: how to avoid mistakes

Reinstalling the rear seat requires no less care than removing it. Follow these rules:

1. Check the condition of the fasteners - if they are deformed, replace them (part number for Qashqai J11: 80310-4M000).
2. Connect the wiring before the seat is finally fixed - this makes it easier to get into the connectors.
3. Make sure the seat belts are are not twisted and move freely in the coils.

After assembly:

• 🔍 Check the work heating (if any).
• 🚗 Make sure the backrest is locked in the reclined position.
• 🔊 Listen extraneous sounds (creaks, knocks) when moving - they may indicate incorrect installation.

⚠️ Attention: B Qashqai J10 after removing the seat it may work airbag error (code B1017). To reset it, disconnect the battery for 10 minutes or use a diagnostic scanner (for example, Launch X431).

💡

Always photograph the location of wires and bolts before disassembling - this will save hours of reassembly.

FAQ: Frequently asked questions about removing the rear seat

Is it possible to remove the rear seat in a Qashqai without tools?

In basic versions J10 without heating and ISOFIX - yes, hand strength is enough to release the latches. However, the backrest mounting bolts will still require a socket wrench. B J11 You won't be able to do it without tools because of the plastic latches that are easy to break.

What is the rear seat weight of the Qashqai?

The pillow weighs ~8–10 kg, the back – 12–15 kg (depending on the configuration). In versions with heating and ventilation, the weight can reach 18 kg. It is recommended to remove the seat with an assistant to avoid damage.

What should I do if the seat squeaks after installation?

Creaking usually occurs due to:

• Poorly fixed plastic latches (needs to be disassembled and reinstalled).
• Hits garbage between the metal guides (clean them with compressed air).
• Wear rubber dampers (replace with new ones, article number 80310-1X000).

Where is the fuse for heated rear seats in a Qashqai?

In the mounting block under the steering wheel (to the left of the pedals). Look for the fuse F37 (15A) — he is responsible for the heating circuit. B J11 also check the relay K34located nearby.

Is it possible to wash a removed Qashqai seat with water?

The pillow can be cleaned damp sponge with car shampoo (for example, Sonax Upholstery Cleaner), but do not immerse it in water - this will damage the filler. Wipe the back without excessive moisture, especially if it has heating wires. For drying use hair dryer in cold mode.