Nissan Almera G15 is one of the most popular sedans in Russia, but even this reliable car loses its light beam settings over time. Incorrectly adjusted headlights blind oncoming drivers, impair visibility in the dark and can result in a fine. In this article we will look at how to independently adjust the low and high beam to Almera G15 (2013–2026) without visiting a service center, using available tools and proven schemes.

We analyzed the official manuals Nissan, owner reviews from forums Drive2 And Almera-Club.ru, and also took into account the features of the restyled versions (2016 and 2019). The manual contains step-by-step instructions for halogen and LED headlights, angle tables, and common mistakes, which spoil the result. If you have never adjusted optics, no problem: our checklist and video examples will help you avoid common mistakes.

When do you need to adjust your headlights? Nissan Almera G15?

Light beam on Almera G15 gets lost more often than it seems. Here are the key signs that it's time to start tuning:

  • 🔦 Road lighting has become uneven — one headlight shines higher than the other, or the light “goes” to the side.
  • 🚗 Oncoming drivers blink their lights (even with the low beam switched on correctly).
  • 📏 After replacing lamps, suspension repairs or an accident (even light ones).
  • 🔧 After installing fog lights or LED lamps (they require a different setup!).
  • 🛣️ When driving on uneven roads (for example, after a trip off-road or potholes).

Please note: on Almera G15 Headlights are often installed from the factory with automatic corrector (if the car is in a top configuration). In this case, adjustment may not be required - the system itself adjusts the tilt angle depending on the vehicle load. You can check its operation through the on-board computer menu: go to Settings → Lighting → Automatic headlight leveling.

⚠️ Attention: If, after replacing the lamps with LEDs, the headlights begin to glare more, the problem is not in the adjustment, but in incorrect selection of light temperature. Lamps with a higher color temperature 5000K (cool white/blue) are prohibited by traffic regulations and blind oncoming traffic, even if the angle of inclination is correct.

Preparing for adjustment: tools and conditions

For fine adjustment of headlights Nissan Almera G15 you will need:

  • 🔧 Phillips screwdriver (for adjustment screws).
  • 📏 Tape measure or laser level (for marking the wall).
  • 🎯 Chalk or masking tape (to mark the centers of the headlights).
  • 🚗 Level ground (no slope) in front of a wall or gate.
  • 🔋 Battery charger (if adjustment takes more than 30 minutes).

It is important to create ideal conditions to configure:

  1. Place the machine on a level surface in 5 meters from the wall (3–7 m is allowed, but 5 m is optimal).
  2. Check the tire pressure - it should be the same and comply with the norm (2.2 bar front and 2.0 bar behind for Almera G15).
  3. Make sure there is no less in the tank ½ fuel, and there are no heavy objects in the trunk.
  4. Have a helper sit in the driver's seat (or place a load 70–80 kg) to simulate the driver's weight.
📊 What kind of bulbs are in your headlights?
  • Halogen (factory)
  • Light Emitting Diodes (LED)
  • Xenon
  • I don't know

If you have restyled Almera G15 (2019+), please note that the shape of the headlight diffuser has changed - the light beam has become wider. For such models it is recommended to use tilt angles 0.2° lower, than for finishing 2013–2018.

Headlight adjustment diagram Nissan Almera G15: step by step instructions

On Almera G15 adjustment is carried out by two screws on each headlight:

  • 🔄 Vertical screw (up/down) - located on top of the headlight, under the hood.
  • ↔️ Horizontal screw (left/right) - hidden on the side, closer to the radiator.

To access them, you do not need to remove the headlight - just open the hood and find the plastic caps (on some versions they are missing).

Find a flat area in front of the wall (5 m)

Check tire pressure

Fill the tank at least ½ full

Place an assistant in the driver's seat (or place a 70 kg load)

Mark the centers of the headlights and the center line of the car on the wall-->

Step 1. Marking the wall

Mark the wall (or garage door) with the following marks:

  1. Draw a vertical line corresponding central axis of the machine (it should go between the headlights).
  2. Mark the centers of both headlights (the distance between them is Almera G15 — 1020 mm).
  3. Draw a horizontal line at the level headlight centers (usually 60–65 cm from the ground, depends on the configuration).
  4. On 7.5 cm below draw a second horizontal line - this is line of the upper boundary of the light spot for low beam.

Step 2: Vertical adjustment

Turn on low beam and start setting up:

  1. Cover one headlight with thick cloth or cardboard (so that the light does not interfere).
  2. Rotate vertical screw (above the headlight) until the upper edge of the light spot coincides with the lower horizontal line on the wall.
  3. For Almera G15 with halogen lamps the angle of inclination should be 1.0–1.2°, for LED - 0.8–1.0°.
  4. Repeat for the second headlight.

Step 3: Horizontal Adjustment

Horizontal adjustment is needed if the light “goes” to the left or right. To do this:

  1. Check that break point of the light spot (where the light starts to rise) was on a vertical line corresponding to the center of the headlight.
  2. If not, rotate horizontal screw (on the side of the headlight) until it matches.
💡

If the adjustment screws turn but do not lock, try placing a thin rubber gasket under them or adding a drop of superglue (carefully!). This is a common problem on Almera G15 after 100,000 km.

Table: optimal headlight angles for Nissan Almera G15

Lamp type Tilt angle (vertical), ° Permissible deviation, ° Features
Halogen (factory) 1.0–1.2 ±0.1 Standard setting on most trims
Light Emitting Diodes (LED) 0.8–1.0 ±0.1 Requires more precise adjustment due to brightness
Xenon 0.9–1.1 ±0.05 It is mandatory to check the automatic corrector
Halogen (restyling 2019+) 0.9–1.1 ±0.1 Consider the modified diffuser shape

If your machine is equipped automatic headlight leveling, after manual adjustment, reset its settings through the on-board computer menu: Settings → Lighting → Reset corrector.

Common mistakes and how to avoid them

Even experienced drivers make mistakes when adjusting headlights. Here TOP-5 errors on Nissan Almera G15:

  • ❌ Adjustment on uneven ground - even a slight slope in 1–2° distorts the result. Use the level!
  • ❌ Ignoring machine loading - if adjusted without a load on the driver's seat, the headlights will shine too high.
  • ❌ Setting up only one headlight - if one headlight is adjusted correctly and the other is not, this creates a dangerous asymmetry.
  • ❌ Using unsuitable lamps - LEDs with temperature 6000K+ are prohibited and blind even when configured correctly.
  • ❌ Forgetting to check the fog lights - their light beam also needs to be adjusted (angle of inclination - 0.5–0.7°).
⚠️ Attention: On Almera G15 with automatic headlight leveling (Auto Leveling) manual adjustment may fail after turning on the ignition. Always check the result with the engine running - this is how the corrector is activated and adjusts the angle to the actual load of the machine.
What to do if the adjustment screws are broken?

If the screws are loose or broken, there are two options:

1. **Temporary repair**: place a thin washer or rubber gasket under the screw, then secure with superglue.

2. **Permanent solution**: replace the adjustment unit (part number for Almera G15 — **26060-4M000** for the left headlight, **26060-4M001** for the right one). The cost of the part is about 1,500–2,000 rubles per piece.

Adjusting headlights after replacing lamps or installing LEDs

If you changed halogen lamps to light emitting diodes (LED) or xenon, standard adjustment will not work. Here's what to consider:

  • 💡 LEDs have a different focus and require lower inclination angle (on 0.2–0.3° lower than halogen).
  • ⚡ Xenon must be completed automatic corrector And headlight washer (otherwise it will not pass inspection).
  • 🔧 After replacing lamps check if it has moved reflector - sometimes it moves during installation.

For Almera G15 recommended for use with LED lamps special adapters (for example, from Morimoto or Philips), which simulate the position of the filament of a halogen lamp. Without them, the light beam will be blurry.

On Almera G15 2019–2026 with factory halogen headlights, installing LED lamps without modifying the reflector leads to blinding oncoming drivers at a distance of up to 200 meters - this is a violation of clause 3.4 of the traffic rules and a fine of 500 ₽.

Checking the result: how to understand that the headlights are adjusted correctly

After setup it is necessary test the headlights in real conditions:

  1. Drive along dark straight road (without oncoming cars) and evaluate the lighting:
    • ✅ Low beam should illuminate 30–40 m ahead.
    • ✅ The upper border of the light spot is clear, without blur.
    • ✅ There are no “dips” in lighting on the sides.
  • Have an assistant stand in 50 meters in front of the car - he should not feel blinded.
  • Check how the light falls on road signs - they should be clearly visible, but not blinding.

    • If something is wrong, go back to the adjustment. On Almera G15 most often it is necessary tighten the vertical screw, since the horizontal adjustment is less likely to go astray.

    💡

    After adjustment, be sure to check the headlights while driving! The static setting on the wall does not take into account vibrations and tilt of the machine when driving.

    FAQ: answers to frequently asked questions

    Is it possible to adjust the headlights Nissan Almera G15 without marking the wall?

    Yes, but the accuracy will be lower. Alternative way:

    1. Park the machine on a level surface.
    2. Turn on your low beams and mark on the asphalt in front of the car light spot boundary.
    3. Pull back to 5 meters — the border should fall by 7–10 cm. If not, adjust with screws.
    How often should headlights be adjusted? Almera G15?

    Recommended frequency:

    • After replacing lamps or headlights.
    • After suspension repair or an accident.
    • Every 20,000 km mileage (or once a year).
    • When the season changes (in winter, due to snow on the roof, the car may “lift”).
    What to do if after adjustment one headlight shines dimmer?

    Causes and solutions:

    • Oxidation of contacts — clean the lamp connectors.
    • Bad ground wire — check the fastening of the “minus” to the body.
    • Burnt out reflector - The headlight needs to be replaced.
    • Different lamp temperatures - Replace both lamps with a pair.
    Is it possible to adjust the headlights Almera G15 using a mobile application?

    Yes, there are applications like Headlight Adjustment or Car Light Tester, but they only give approximate results. For fine tuning it is better to use laser level or professional equipment in service.

    Which lamps are best to put on Almera G15 for better light?

    Lamp recommendations:

    • Halogen: Osram Night Breaker Laser (+150% light) or Philips X-tremeVision.
    • LED: Philips Ultinon Essence (if permitted by law) or Morimoto 2Stroke 2.0.
    • Xenon: Only with lenses and washers (For example, Sho-Me H7).

    Important: LEDs without modification of the reflector blinds oncoming drivers and prohibited by the traffic police!