Redmi Note 13 Pro is one of the most popular smartphones of 2026, combining powerful hardware, stylish design and an affordable price. But what to do if the device fails? Replacing a screen, battery or speaker often requires complete disassembly, and official service centers charge a lot of money for this. In this guide we will explain in detail how to disassemble Redmi Note 13 Pro yourself without damaging fragile components.

It is important to understand: disassembling a smartphone is always a risk. Even with careful actions, you can damage the cables, break the latches or break the seal of the case. If you have never disassembled phones before, it is better to practice on an old device or contact a professional. In this article we will talk not only about the sequence of actions, but also about typical mistakesthat beginners make, and we will also give advice on choosing tools and spare parts.

Preparing for Disassembly: Tools and Precautions

Before you start disassembling Redmi Note 13 Pro, make sure you have everything you need. Unsuitable tools may damage the housing or internal components. Here is the minimum set you will need:

  • 🔧 Plastic spatulas (preferably a set with different thicknesses - 0.2 mm, 0.4 mm, 0.6 mm). Use metal picks it's impossible!
  • 🔨 Screwdriver T3 and T4 (for case and motherboard screws). It is better to take magnetic ones so that the screws do not get lost.
  • 🔥 Hair dryer or hot air station (to soften the glue under the back cover). Temperature - no higher 80°C!
  • 🧲 Suckers (to gently lift the screen or back panel). Diameter - 5-7 cm.
  • 📦 Container for screws (so as not to confuse them during assembly). Even a foam egg will do.
  • 🧴 Isopropyl alcohol (90%+) and lint-free wipes for cleaning the adhesive.

Also prepare your workplace: it should be well lit, without drafts (dust can get inside the smartphone) and with an antistatic coating (for example, a silicone mat). Do not work on a carpet or sofa - static electricity can damage the motherboard.

⚠️ Attention: If you parse Redmi Note 13 Pro with a valid warranty, please note that after opening the case the warranty automatically canceled. The manufacturer can easily determine the interference by marks on the screws or stickers.

Before starting work turn it off completely smartphone and remove the SIM card and memory card. If the battery is swollen, do not try to disassemble the device yourself - contact service! A swollen battery can ignite if punctured.

Removing the back cover: how not to damage the adhesive and latches

Back cover Redmi Note 13 Pro attached with glue and plastic latches. If you pull it by force, you can break the fastenings or break the cables. We recommend the following algorithm:

  1. Heat the back panel with a hairdryer for 2-3 minuteskeeping him at a distance 5-7 cm. Move the hairdryer in a circle to soften the glue evenly.
  2. Use a suction cup to carefully lift the cover from one of the corners (it’s better to start from the bottom left, where there are no cables).
  3. Insert a plastic spatula into the resulting gap and slowly move it along the body, separating the glue. Do not press too hard - you may damage the antenna contacts!
  4. When the lid comes off 2/3, check if the cables are interfering (for example, the fingerprint scanner cable). If yes, carefully disconnect them.

On Redmi Note 13 Pro The back cover is often glued very tightly, especially in the camera area. If it does not give in, do not try to tear it off - it is better to warm up the problem area again. Also be careful with metal frame around the camera: it may leave scratches on the shoulder blade.

Is the glue heated around the entire perimeter?|Is there a suction cup at hand?|Are there any cables nearby that could interfere?|Are you prepared for the possibility that the lid may crack?-->

After removing the cover, you will see the battery, motherboard and several cables. Don't touch them with your hands - static electricity can damage microcircuits. If you need to put the lid down, place it on a soft surface (such as a napkin) to avoid scratching it.

Disabling the Battery: Why It's Critical

Before touching any internal components, be sure to disconnect the battery. B Redmi Note 13 Pro it is attached with glue and connected to the motherboard via a connector. If you do not disconnect it, you can cause a short circuit that will damage the power controller.

The battery in this model is glued quite tightly, but you can remove it without a hairdryer. Here's how to do it:

  1. Locate the battery connector on the motherboard (usually located at the bottom, next to the USB port).
  2. Using a plastic spatula, carefully pry out the connector from the side (not up!). Pull on the black plastic tab, not the wires.
  3. If the battery is swollen, do not try to remove it - it is dangerous! In this case, it is better to immediately contact the service.
⚠️ Attention: If, when disconnecting the battery, you see oxidation on connector contacts, this is a sign of moisture penetration. In this case, it is better to stop disassembling and take the phone to a service center - the board may need to be replaced.

After disconnecting the battery, you can begin removing the motherboard or other components. But remember: the longer the battery is left disconnected, the higher the risk of it draining to zero. If you plan to use your phone for a long time, it is better to connect it to a power source via USB-C (but only after complete assembly!).

Yes, many times|Yes, but only the screen|No, this is my first experience|I tried it, but something broke-->

Removing the motherboard: connectors and traps

Motherboard Redmi Note 13 Pro secured with several screws and connected to multiple cables. If you've never worked with electronics, this step may seem daunting. Main rule: take pictures of every stepso that you can assemble everything correctly later.

Procedure:

  1. Unscrew all the screws securing the metal plate above the motherboard (usually 6-8 of them). Place them in a container so you don't lose them.
  2. Carefully remove the metal plate. Under it you will see cables for the camera, speaker and buttons.
  3. Disconnect all connectors, starting with the largest ones. B Redmi Note 13 Pro they usually have latches that need to be lifted before removing the cable.
  4. After disconnecting all cables, the board can be carefully lifted. Do not pull it by force - check if there are any unnoticed fasteners left.
Connector Purpose Disabling Features
J1 Main camera Thin train, breaks easily. Pry from the side!
J3 Display Fastened with a latch. First lift it, then pull the train.
J5 Battery May stick to the board. Don't yank - gently rock.
J7 Charging port Often oxidized. If the contacts are green, clean with alcohol.

If you are removing a board to replace it, please note thermal paste under the processor. B Redmi Note 13 Pro it often dries out, which leads to overheating. When assembling, it is better to apply a new one (for example, Arctic MX-6).

💡

If the screws won't come off, don't push harder—try adding a little WD-40 or alcohol. Often they simply “stick” to the thread.

Screen replacement: difficulties and pitfalls

Screen Redmi Note 13 Pro - one of the most expensive spare parts, and its replacement requires special care. In this model, the display is glued to the touchscreen, so if one is damaged, the entire module has to be replaced. Here's what you need to know:

  • 📱 Screen type: AMOLED, 120 Hz, with an integrated fingerprint scanner. The function may not support replacement with a non-original screen. Always-On Display.
  • 🔧 Glue: Double sided tape is used 3M high strength. To replace, you need new glue (for example, Tesa 61395).
  • ⚡ Trains: The screen is connected by two cables - the main one (image) and the additional one (touchscreen). It's easy to confuse them!
  • 💰 Cost: The original screen will cost 15 000–20 000 ₽, unoriginal - 8 000–12 000 ₽.

Replacement process:

  1. Warm up the screen with a hairdryer (temperature - 70°C, time - 3-4 minutes).
  2. Use a suction cup to lift the screen from the bottom edge (where there are no cables).
  3. Insert a plastic spatula and carefully move it around the perimeter, removing the glue.
  4. Disconnect the cables and remove the screen. Be careful - there may be fingerprint scanner glass on the back side!
⚠️ Attention: If after replacing the screen the touchscreen does not work or artifacts are displayed, check whether the cables are connected correctly. Often the problem is solved by reconnecting. If not, the screen may be defective.

When installing a new screen, do not forget check it before sticking. Connect the cables and temporarily turn on the phone (without fixing the screen) to make sure everything is working. Only then apply new glue and fix the display.

What should I do if the screen does not turn on after replacement?

1. Check whether both cables (main and touchscreen) are connected correctly.

2. Make sure the battery is connected and charged (at least 10%).

3. Try to reboot your phone by holding Power + Volume Up within 10 seconds.

4. If the screen still does not work, the motherboard may be damaged or the display itself may be defective.

Battery replacement: when you really need it

Battery in Redmi Note 13 Pro has a capacity 5100 mAh and is designed for 800–1000 cycles charging. If your phone starts to drain quickly or suddenly turns off, it may be time for a replacement. But first check:

  • 🔋 Battery wear: In settings (Settings → Battery → Battery status) look at the wear percentage. If it's higher 25%, replacement is justified.
  • ⚡ Charger: Are you using the original power supply? Non-original chargers can damage the battery.
  • 🔥 Overheat: If your phone gets hotter 45°C when charging, this may indicate a faulty battery.

To replace the battery:

  1. Disconnect the old battery (as described above).
  2. Use a plastic spatula to pry it off and carefully separate it from the body. The glue is usually not very strong, but additional heat may be required.
  3. Install a new battery (eg Original Xiaomi BM4X) and connect the cable.
  4. Test the phone's operation before final assembly.

After replacing the battery, it is recommended calibrate it: Discharge your phone completely, then charge it to 100% no breaks. Repeat the procedure 2-3 times. This will help the controller correctly determine the capacity.

💡

Do not buy cheap batteries from unknown brands! They may swell or ignite. It is better to overpay for the original or a certified analogue (for example, Patona).

Assembling a phone: how to avoid mistakes

Assembly Redmi Note 13 Pro after disassembly is no less important a process than the disassembly itself. Main rules:

  • 🔧 Screws: Screw them in the same order in which you unscrewed them. Do not overtighten - you may break the thread!
  • 🧩 Trains: Make sure all connectors are fully latched. Check for gaps.
  • 🔋 Battery: Before fixing with glue, check that it lies flat and is not distorted.
  • 📱 Screen: After gluing, check the sensitivity of the touchscreen in all corners.

After assembly, turn on the phone and check:

  • Does the touchscreen work (especially around the edges).
  • Is the battery charging?
  • Are the cameras, speakers and microphone functioning?
  • Is there any overheating (check in Settings → Device status).

If something doesn't work, don't panic. Go back and check:

  • Are all cables connected?
  • Are the wires pinched somewhere?
  • Did you remember to connect the battery?
⚠️ Attention: If after assembly the phone does not turn on, but shows an indication when connected to a charger, the problem is most likely power cable or power button. If there is no indication at all, the motherboard may be damaged.

FAQ: answers to frequently asked questions

Is it possible to disassemble Redmi Note 13 Pro without a hair dryer?

Theoretically yes, but it is very risky. The adhesive on the back cover and screen is quite strong, and without heat you can break the latches or tear the cables. If you don't have a hairdryer, try using hot water in a bag (apply it to the lid for 5 minutes), but this method is less reliable.

What should I do if the camera does not work after disassembling?

Most likely, you either did not connect the camera cable or damaged it during disassembly. Open your phone again and check:

  • Is the cable connected to the connector? J1 on the motherboard.
  • Are there any breaks or dirt on the cable?
  • Is the cable pinched somewhere inside the case?

If the cable is damaged, it will have to be replaced (cost is approx. 1 500 ₽).

What glue should I use for the screen?

For Redmi Note 13 Pro suitable:

  • Tesa 61395 - double-sided tape, easy to stick, but can come off if overheated.
  • 3M 9448A - more durable, but more difficult to install.
  • B7000 - liquid glue, requires drying 24 hours, but holds securely.

Do not use superglue or moment! They will damage the screen and case.

How much does a service disassembly cost?

Disassembly cost Redmi Note 13 Pro at service centers:

  • Diagnostics - 500–1 000 ₽.
  • Screen replacement - 3 000–5 000 ₽ (excluding cost of spare parts).
  • Battery replacement - 1 500–2 500 ₽.
  • Cleaning from dust - 1 000–1 500 ₽.

Prices may vary depending on the region and complexity of the work.

Is it possible to disassemble a phone with water inside?

No! If in Redmi Note 13 Pro water has entered, disassembly may aggravate the situation. Moisture in contact with air oxidizes the contacts, and mechanical stress spreads corrosion. In this case:

  1. Turn off your phone immediately.
  2. Put it in a bag of silica gel (or rice) on 24–48 hours.
  3. Contact the service for professional ultrasonic cleaning.

Self-disassembly is justified only if water got in more than a day ago and the phone is already dry.