Dimensions of Nissan Teana J31 wipers: original part numbers, analogues and replacement nuances

Replacing wipers with Nissan Teana J31 (2003–2008) - a seemingly simple procedure, but mistakes here are fraught with consequences. Improperly sized blades can result in poor fit, scratches on the glass, or even breakage of the windshield wiper mechanism. In this article - exact dimensions of wipers for all modifications of J31, including restyled versions, original articles Nissan and proven analogues, as well as unique nuances of fastenings that are not written about in standard instructions.

Feature Teana J31 — asymmetrical length of the brushes (driver and passenger sides are different), and the parameters depend on the year of manufacture and configuration. For example, machines with the option Rain Sensor require brushes with a special coating, and for versions with Panoramic Roof We need shortened versions. We will analyze all cases, including rare exceptions, and provide a checklist for an error-free selection.

Official wiper sizes for Nissan Teana J31 by year

Basic dimensions of wiper blades for Teana J31 (2003–2008) as follows:

• 🚗 Driver's side (left): 600 mm (24 inches)
• 🚗 Passenger side (right): 400 mm (16 inches)

However, there are nuances:

• 🔧 For cars 2006–2008 (restyling) with option Auto Wipers The length of the driver's brush can be 610 mm - this is due to the changed angle of rotation of the trapezoid.
• 🌧️ Cars with Rain Sensor (rain sensor) require brushes with graphite coating to reduce electrical interference.
• 🚘 Versions with Panoramic Roof (panoramic roof) are equipped with brushes on 20 mm shorter on each side to avoid touching the seal.

Year of manufacture	Driver side (mm)	Passenger side (mm)	Notes
2003–2005	600	400	Standard equipment, without rain sensor
2006–2008 (restyling)	610	400	With option Auto Wipers or Rain Sensor
2005–2008 (Panoramic Roof)	580	380	Short brushes to avoid contact with the roof seal

⚠️ Attention: If on your Teana J31 brushes of non-standard length are installed (for example, 650 mm), this may be a consequence of a previous incorrect replacement. Long blades increase the load on the windshield wiper motor and reduce its service life.

Original articles and fasteners: what you need to know

Original wipers for Nissan Teana J31 are supplied under the following article numbers:

• 📌 28550-4M000 — driver’s brush (600 mm)
• 📌 28551-4M000 — passenger brush (400 mm)
• 📌 28550-4M001 — driver’s brush for restyling (610 mm)

Key Features - fastening type. On Teana J31 used Hook (U-type) with size 9×3 mm. However, in some configurations (for example, with heated brush resting zone), a modified mount is used Side Pin (art. 28550-4M010). You can check the type visually:

• 🔍 Hook: metal hook visible when the brush is removed.
• 🔍 Side Pin: plastic pin on the side, often hidden by a protective cap.

⚠️ Attention: When purchasing analogues, check not only the length, but also the type of fastening. For example, brushes Bosch Aerotwin with fastening Hook 9x4 mm will not fit - a difference of 1 mm will lead to play and vibration during operation.

Check the year of manufacture and equipment of Teana J31|Check the type of fastening (Hook or Side Pin)|Measure the old brushes (the length may differ from the standard one)|Pay attention to the presence of a rain sensor|Compare the article numbers of original and analog brushes-->

The best analogues of original wipers: rating 2026

Original brushes Nissan cost from 1,500 to 2,500 rubles per set, but there are worthy analogues on the market with a better price/quality ratio. We tested 10 brands and selected the top 5:

1. Bosch Aerotwin AR601S + AR400S — frameless, with graphite coating, ideal for machines with Rain Sensor. Price: ~2,200 rub.
2. Valeo Silencio X-TRM 600 + 400 - quiet, with an aerodynamic profile. Suitable for speeds over 120 km/h. Price: ~1,800 rub.
3. SWF VisioNext 600/400 - a budget option (from 900 rubles), but with good wear resistance. Minus: they work worse in frost below –15°C.
4. Champion EasyVision 600 + 400 — optimal for regions with frequent precipitation. Includes adapters for different mounts.
5. HELLA EcoWiper 600/400 - the only ones in the ranking with heated (for northern regions). Price: ~2,500 rub.

💡 Advice: If you often drive on the highway, choose brushes with spoiler (For example, Valeo Silencio). They adhere better to the glass at high speeds. Frameless models are suitable for the city (Bosch Aerotwin), which freeze less in winter.

How to properly replace wipers on Teana J31: step-by-step instructions

Replacing brushes with Nissan Teana J31 takes no more than 10 minutes, but there is 3 critical pointsthat are often missed:

1. Wiper position. Before replacing, turn off the ignition and wait until the brushes return to bottom position (rest zone). If you interrupt the process mid-cycle, the motor may burn out the next time you turn it on.
2. Lever fixation. When removing the old brush don't pull it up — press the fastening latch (usually it is red or black) and move the brush to the side.
3. Installation angle. New brush must be installed perpendicular to the glass. If you skew it even by 5°, it will “bounce” during operation.

Step-by-step algorithm:

1. Raise the wiper arm to a vertical position (it will lock itself).
2. Press the fastening lock and remove the old brush.
3. Compare the attachment of the new brush with the old one. If necessary, use an adapter (included with most analogues).
4. Install the new brush until it clicks. Make sure the latch snaps into place.
5. Lower the lever onto the glass smoothly, without impact.

⚠️ Attention: If after replacing the brushes there are streaks left, check lever angle. On Teana J31 he must be 15–20° from the vertical. At a smaller angle, the brush will not press against the edges of the glass.

What to do if new wipers squeak?

Creaking is usually caused by two reasons:

1) Incompatible rubber material - some budget brushes (for example, Finwhale) contain rubber, which hardens in the cold.

2) Glass contamination — before installing new blades, clean the glass degreaser (For example, Liqui Moly Scheiben-Reiniger).

If the squeaking does not go away, try applying brushes to the rubber silicone grease (not to be confused with WD-40!).

Common mistakes when choosing and replacing wipers

Even experienced drivers make mistakes that lead to premature wear of the brushes or breakdown of the mechanism. Here TOP-5 misses with Teana J31:

• 🚫 Ignoring the rain sensor. Brushes without graphite coating interfere with the sensor, causing it to trigger falsely.
• 🚫 Installation of brushes from other Nissan models.Nissan Maxima A33 are similar in appearance, but have a different bend radius - they do not clean the edges of the glass well.
• 🚫 Using universal adapters. They often play, which leads to vibrations at high speeds.
• 🚫 Replacement of only one brush. Different degrees of wear lead to uneven pressure and accelerated wear of the new brush.
• 🚫 Neglecting to adjust the levers. On Teana J31 the levers sag over time - they need to be tightened with a wrench 10 mm (instructions in the next section).

🔧 How to check if the installation is correct? Turn on the wipers at minimum speed and watch them work:

- If the brushes "bounce" on the edges of the glass - they are too long or poorly pressed.

- If they remain stripes — the tires are too hard (typical for cheap analogues).

- If you can hear knock — the fastening is not fixed or the adapter is selected incorrectly.

💡

On Teana J31 with a rain sensor, you cannot use brushes with metal inserts - they create electromagnetic interference, which causes the sensor to not work correctly.

Adjustment and maintenance of wipers: extending service life

Wiper blades on Teana J31 serve on average 6–12 months, but with proper care this period can be increased to 18 months. Here's what to do:

• 💧 Wash your brushes once a month warm water and soap (eg Fairy). This removes micro-particles of sand that scratch the glass.
• ❄️ Treat your gum in winter silicone grease (not to be confused with WD-40!). Will do Liqui Moly Silikon-Spray.
• 🔧 Adjust the tension of the levers every 20,000 km. To do this:

1. Remove the protective cap from the lever shaft.
2. Tighten the nut with a wrench 10 mm (tightening torque - 1.5 Nm).
3. Check for smooth movement - the lever should move without jamming.

⚠️ Attention: If the wipers start to “flood” (stop outside the rest zone), this is a sign motor gear wear. In this case, it is useless to change the brushes - diagnostics of the drive is needed.

💡 Lifehack: To prevent the brushes from freezing in winter, raise them to a vertical position before parking them overnight. If ice has already formed, don't turn on the wipers - water icy areas warm water with salt (1 tbsp per 0.5 l).

FAQ: Frequently asked questions about wipers for Nissan Teana J31

Is it possible to install frameless wipers on Teana J31?

Yes, but only if they are certified for curved glass. On Teana J31 will fit Bosch Aerotwin or Valeo Silencio. Conventional frameless brushes (for example, from Hyundai) do not follow the curve of the glass and leave uncleaned areas around the edges.

Why do new wipers not clean glass well?

There are three reasons:

1. Oily film on glass - clean it degreaser (For example, Sonax Glass Cleaner).
2. Incorrect installation angle - adjust the levers (see section above).
3. Rubber defect — check the brush by touch: if rubber too hard, replace it under warranty.

What size wipers for Teana J31 with panoramic roof?

For versions with Panoramic Roof shortened brushes are used:

- Driver's license: 580 mm

- Passenger: 380 mm

Original articles: 28550-4M020 (left) and 28551-4M020 (right).

Is it possible to restore old wipers?

Partially yes. To do this:

1. Remove the brush and wash it in vinegar solution (1:1 with water) - this will remove deposits.
2. Strip the gum sandpaper P1000 (only along, not across!).
3. Apply silicone grease to restore elasticity.

⚠️ This is a temporary measure! After 1–2 months, the brushes will still have to be replaced.

Where can I find the original part numbers by VIN?

Use official directories:

• Nissan Parts Europe (enter VIN in search).
• Nissan TechInfo (registration required).

For Teana J31 catalog is also suitable Amayama — there is a filter by year and configuration.