Wiper blade sizes for Nissan Qashqai J11: compatibility table and selection recommendations

Replacing windshield wiper blades with Nissan Qashqai J11 (2014–2021 model year) - a seemingly simple procedure, but even here owners are faced with nuances. An error in choosing the length of the wipers leads to poor fit, squeaking or even damage to the windshield. The problem is especially relevant for restyled versions J11 (since 2017), where the manufacturer sometimes changed suppliers of original spare parts.

In this article - exact brush sizes for all modifications of Qashqai J11, including versions with panoramic roof And LED headlights, where the glass geometry may differ. We have sorted out the original articles Nissan, compatible analogues from Bosch, Denso and other brands, as well as typical selection errors. If you have already encountered the problem that new wipers do not reach the edges of the glass or leave streaks, you will find a solution here.

Official brush sizes for Nissan Qashqai J11 (2014–2021)

The manufacturer installs on Qashqai J11 Wiper blades in the following sizes:

• 🚗 Front left (driver's side): 650 mm (26 inches)
• 🚗 Front right (passenger side): 400 mm (16 inches)
• 🚘 Rear: 330 mm (13 inches) - only for versions with rear wiper

Important: these parameters are relevant for all trim levels J11, including Visia, Acenta, N-Connecta And Tekna. The exception is cars with panoramic roof (optional B92), where due to the changed angle of the glass, brushes 10–15 mm shorter are sometimes required. More details about this can be found in the section on selection nuances.

Brush position	Size(mm)	Nissan part number	Note
Front left	650	28260-4M00A	Original, frame type
Front right	400	28261-4M00A	Original, frame type
Rear	330	28560-4M000	Only for versions with rear wiper
Front left (frameless)	650	28260-4M01A	Optional original for restyling

⚠️ Attention: There are fakes of original brushes on the market. Nissan with articles 28260-4M00A And 28261-4M00A. You can distinguish them by the quality of the fastening plastic - counterfeit ones are fragile and have burrs. Also check for a hologram on the packaging.

Frameless vs frame brushes: which is better for Qashqai J11

Owners Qashqai J11 There is often a debate about which wipers are more effective: traditional frame or modern frameless. The first type is cheaper (from 300 rubles per pair), but copes worse with icing and wears out faster. Frameless ones (from 800 rubles) adhere better to the glass, especially at high speeds, but can “bounce” in severe frost.

• ✅ Frame advantages: low price, easy to replace the rubber element, resistance to mechanical damage.
• ❌ Frame cons: accumulate snow in winter, clean the edges of the glass worse due to less flexibility.
• ✅ Frameless advantages: uniform pressure along the entire length, less noise, long service life (up to 2 years).
• ❌ Frameless cons: high price, difficult to select for non-standard glasses (for example, heated).

For Qashqai J11 with panoramic roof We recommend frameless brushes - they better follow the curve of the glass. For standard versions, both options are suitable, but if you often ride on the highway, frameless is preferable due to less wind resistance.

Compatible analogues: which brands are suitable for replacement

Original brushes Nissan cost from 1,200 to 1,800 rubles. per set, but there are decent cheaper analogues on the market. The main thing is to check not only the size, but also fastening type. On Qashqai J11 mount is used Hook (U-bracket) or Side Pin for the rear brush.

The best analogue brands in terms of price/quality ratio:

• 🔹 Bosch Aerotwin (frameless): articles AR650S (left) and AR400S (right). Price ~1,500 rub. for a couple. They feature an asymmetrical profile for a better fit.
• 🔹 Denso Flat Blade: articles DF-065L And DF-040R. Cost ~1,200 rub. Japanese quality, UV resistant.
• 🔹 Valeo Silencio X-TRM: articles 600165 And 600140. Price ~1,000 rub. Good for winter use.
• 🔹 Champion EasyVision: budget option (~600 rubles per pair), but they last no more than a year.

⚠️ Attention: When purchasing analogues, avoid brushes with metal elements in the mount - they can scratch the glass Qashqai J11, especially if it has a factory coating Nissan Scratch Shield (optional KH3).

Make sure the size matches the original (650/400 mm)

Check the type of fastening (Hook for front, Side Pin for rear)

Avoid brushes with metal inserts

Pay attention to the presence of a winter mode (for frameless)

Compare weight - high-quality brushes weigh from 150 g (light ones are often of poor quality) -->

Selection nuances for restyled versions (2017–2021)

After restyling in 2017 Nissan Qashqai J11 received an updated windshield with a changed angle at the top. This led to two problems:

1. The brushes do not reach the edges. If you notice that after replacement, the wipers leave uncleaned areas on the sides, most likely the blades you purchased are too short. Solution: take the left brush to 660 mm instead of 650 mm (For example, Bosch AR660S).
2. Creak when working. It occurs because frameless brushes are poorly adapted to the new curve of the glass. Solution: use hybrid models (e.g. Valeo Silencio Hybrid).

Also sometimes found on restyled versions Large rear wiper — 350 mm instead of 330 mm. This applies to vehicles with the option Rear Wiper (code C16). You can check the size by measuring your old brush or looking at the sticker on the back.

How to measure a brush without removing it?

If it is not possible to remove the brush, use a tape measure or ruler, placing it along the rubber element from one end of the mount to the other. Please note that the length is indicated according to working part (without plastic plugs). For accuracy, measure both brushes - sometimes even on the same car they can differ by 5-10 mm due to deformation.

Step-by-step instructions for replacing brushes on Qashqai J11

Replacing the front brushes takes no more than 5 minutes. All you need is a flathead screwdriver (to pry up the retainer) and new wipers. Algorithm:

1. Raise the windshield wiper arm to a vertical position (perpendicular to the glass).
2. Press the plastic lock at the base of the brush and slide it down the lever.
3. Remove the old brush and install the new one, clicking the latch until it clicks.
4. Lower the lever back onto the glass.

⚠️ Attention: Do not use force when removing the brush - if the latch does not budge, check to see if it is jammed due to corrosion. In this case, treat the fastener with WD-40 and wait 5-10 minutes.

The rear brush is changed in the same way, but there is a lock like Side Pin. To remove it, pull the brush towards you while holding the lever with your other hand. The new one is installed until it clicks.

Typical mistakes when choosing and replacing brushes

Even experienced car owners make mistakes that lead to rapid wear of the brushes or damage to the glass. Here are the most common:

• 🚫 Buy brushes by model, not by VIN. On Qashqai J11 of the same year of manufacture, glass from different suppliers could be installed (for example, Pilkington or Saint-Gobain), which affects the curvature. Always check the size according VIN or measure old brushes.
• 🚫 Ignoring fastening type. Fastening Hook And Side Pin visually similar, but not interchangeable. For example, a brush from Renault Kadjar (twin Qashqai) may not fit due to a different latch.
• 🚫 Saving on winter brushes. Cheap frameless wipers (< 500 rubles) often become dull in the cold. For Qashqai J11 in cold climates it is better to take models with graphite coating (For example, Bosch Winter).
• 🚫 Incorrect installation. If the brush is installed upside down, it will not fit well and will wear out quickly. Most models have an arrow indicating the direction of movement.

Another common problem is windshield wiper arm misalignment after replacement. If the wiper begins to “touch” the plastic casing under the hood, check to see if the lever is bent. This can be corrected by carefully bending it with pliers (but do not overdo it - aluminum alloy is fragile!).

Frequently asked questions (FAQ)

Is it possible to install brushes longer than the original ones, for example, 700 mm instead of 650 mm?

No, this will cause the brush to touch the plastic casing under the hood and quickly wear out. Maximum permissible deviation - +10 mm (for example, 660 mm instead of 650 mm), but only if the glass has a large curvature (as on restyled versions).

Why do new brushes squeak even though the size is correct?

The squeak is usually caused by one of three reasons:

1. Factory lubricant on rubber - wipe the brushes with alcohol.
2. Incompatibility of the wiper material and glass coating (for example, if the glass is tinted).
3. Too hard rubber - typical for cheap frameless brushes.

If the squeaking does not go away after 100 km, replace the brushes with a graphite-coated model.

How often do you need to change brushes on Qashqai J11?

Recommended interval - every 6–12 months or at the first sign of wear:

• The appearance of streaks on the glass.
• Cracks or peeling in the rubber.
• Cleaning becomes worse when it rains (a film of water remains).

In regions with frequent temperature changes (for example, Moscow, St. Petersburg), brushes wear out faster - up to 2 times a year.

Will Renault Kadjar brushes fit Nissan Qashqai J11?

Partially. Renault Kadjar And Nissan Qashqai J11 built on the same platform, but there are nuances:

• The dimensions of the front brushes are the same (650/400 mm).
• The type of fastening may differ - depending on Kadjar sometimes used Bayonet instead of Hook.
• Rear brush on Kadjar often shorter (300 mm against 330 mm).

Before purchasing, check the article numbers or visually compare the fasteners.

Is it possible to restore old brushes without buying new ones?

Yes, but this is a temporary solution. Recovery methods:

1. Rubber sharpening. Gently go over the edge with sandpaper (P1000) at an angle of 45°. This will remove the rough layer.
2. Silicone treatment. Apply silicone lubricant to the rubber band (for example, WD-40 Specialist Silicone) to restore elasticity.
3. Replacing rubber inserts. In frame brushes you can buy new rubber bands (for example, Denso 550-0101) and install them instead of the old ones.

These methods will extend the life of the brushes by 2-3 months, but will not replace a full replacement.