Dimensions of wipers on Nissan Tiida C11 hatchback: originals, analogues and replacement nuances

Why is it important to know the exact dimensions of wipers for Tiida C11?

Wiper blades on Nissan Tiida C11 hatchback (2007–2013) is not just a consumable, but an element of safety. Incorrectly fitted wipers leave streaks, do not adhere well to the glass, or scratch it, especially at high speeds. For example, brushes that are too long can cling to the body pillars, while short ones can leave uncleaned areas, impairing visibility in the rain.

The manufacturer installs on Tiida C11 wipers with clearly defined parameters, but there are variations on the market even with original parts. In addition, after 2010, changes were made to the design of the mounts, which complicates the choice. This article contains current sizes, article numbers of original brushes and proven analogues, as well as step-by-step replacement instructions taking into account typical mistakes.

If you are planning a purchase, please note: the sizes of the front and rear wipers on a hatchback are different from those on a sedan! It is also important to consider fastening type - on Tiida C11 system is used U-hook (9x3 mm), but some analogues require adapters.

Original dimensions of wipers on Nissan Tiida C11 hatchback

Factory brushes for Tiida C11 hatchback have the following parameters:

Position	Size (inches)	Size(cm)	Nissan part number
Front (driver's side)	22"	56 cm	28520-4M000
Front (passenger side)	18"	46 cm	28521-4M000
Rear	12"	30 cm	28530-4M000

Important! Article numbers may vary depending on the year of manufacture. For example, for models 2011–2013. sometimes indicate the article 28520-4M001 for the driver's brush - this is a modification with improved fastening. Check compatibility by VIN or catalogs Nissan.

Original wipers are supplied in original packaging with a logo Nissan and labeling Genuine Parts. Their advantage is a perfect fit and long service life (on average 1–1.5 years with moderate use). However, their price is higher than their analogues: a set of front brushes will cost 2,500–3,200 rubles (for 2026).

Analogs of original wipers: what to choose?

If the original brushes seem too expensive, you can consider analogues from trusted brands. The main thing is to observe the dimensions and type of fastening. Below is a list of reliable alternatives:

• 🔹 Bosch Aerotwin — frameless brushes with an aerodynamic profile. Articles: A338H (22") and A198H (18"). Suitable for Tiida C11 without modifications.
• 🔹 Valeo Silencio X-TRM — premium series with graphite coating. Articles: 600174 (22") and 600168 (18"). 2 year warranty.
• 🔹 SWF Visioflex - a budget option with good cleaning. Articles: 1192002200 (22") and 1192001800 (18"). Fastening U-hook included.
• 🔹 Champion EasyVision — universal brushes with adapters. Suitable if the original mount is worn out. Article: EZ600 (set 22"+18").

⚠️ Attention! Cheap wipers without a brand (for example, from AliExpress) often have inaccurate dimensions. For example, a 22" blade may be 1-2 cm shorter, which will result in incomplete cleaning of the windshield. Check reviews before purchasing.

Suitable for rear wiper:

• 🔹 Bosch Rear - article number A12H (12").
• 🔹 Valeo 600006 - with reinforced mount for hatchbacks.

How to determine wiper wear: 5 key signs

Wiper blades on Nissan Tiida C11 require replacement at least once a year, but with intensive use (for example, in regions with frequent precipitation) - every 6 months. Wear can be determined by the following signs:

1. Stains on glass - even after several passes, streaks or cloudy areas remain.
2. Creaking or knocking during operation - indicates damage to the rubber blade or corrosion of metal parts.
3. Uneven fit — the brush “bounces” off the glass at high speeds.
4. Cracks in rubber - visible damage to the blade, especially along the edges.
5. Deterioration of cleaning in cold weather — the wipers begin to “stick” to the glass or let snow through.

⚠️ Attention! If scratches appear on the glass after replacing the wipers, it is most likely to blame abrasive particles on the rubber of cheap brushes. In this case, it is recommended to polish the glass and install brushes with graphite coating (for example, Valeo Silencio).

Specify the year of manufacture of Tiida C11 (before 2010 or after)

Measure the old brushes (the length may differ from the stated one)

Check the type of fastening (U-hook or bayonet)

Assess the condition of the windshield wiper arms (is there any play)

Compare reviews for the selected brand -->

Step-by-step instructions for replacing wipers with Tiida C11

Replacing brushes with Nissan Tiida C11 the hatchback takes no more than 10 minutes, but requires care. You will need:

• 🔧 New wipers (tested sizes: 22", 18", 12").
• 🧴 Glass cleaner (for example, Sonax).
• 📏 Ruler or tape measure (to check the length).

Step 1. Preparation

Park the car on a level surface and turn off the ignition. Raise the wiper arms to a vertical position (perpendicular to the glass). If the brushes are “stuck,” carefully pry them off with a flat-head screwdriver, but do not use force—you may damage the mechanism.

Step 2. Removing old brushes

Press the fastening release (usually a plastic tab on the side) and pull the brush down. If the fastener is rusty, treat it WD-40 10 minutes before dismantling. On Tiida C11 system is used U-hook, but some analogues may require an adapter.

Step 3. Installing new brushes

Compare the attachment of the new brushes with the old ones. If it is identical, simply click them until they click. If the mount is different (for example, bayonet), use the adapter included in the kit. After installation, check the tightness of the fit: the brush should evenly touch the glass along its entire length.

Step 4. Test and setup

Turn on the wipers at minimum speed and check:

• No squeaks or knocks.
• Complete glass cleaning (without “dry” zones).
• Synchronized operation of both brushes.

If your wipers leave streaks, wipe the glass isopropyl alcohol - this will remove fat deposits.

What to do if new wipers squeak?

Creaking can occur due to:

1) Dry rubber - wipe the blades with silicone grease (do not use oils!).

2) Wrong angle - adjust the wiper arms (to Tiida C11 this is done with a 10 mm wrench).

3) Glass contamination - use special cleaners (for example, Rain-X).

If the creaking does not disappear, check whether the brush mount is skewed.—>

Typical mistakes when choosing and replacing wipers

Even experienced car owners sometimes make mistakes that lead to premature wear of the blades or damage to the glass. Here are the most common:

1. Ignoring the year of manufacture. On Tiida C11 Before 2010, the wiper arms had a different curve, so the blades on later models may not fit well.
2. Buying “universal” brushes without adapters. For example, wipers from VW Golf similar in appearance, but have fastening bayonetwhich is not suitable for Tiida.
3. Using brushes with a metal frame in winter. In the cold they freeze up and scratch the glass. Best choice for cold climates frameless models (for example, Bosch Aerotwin).
4. Late replacement. If the wiper rubber is cracked, it begins to “grab” dirt and abrasive particles, which accelerates the wear of the glass.

⚠️ Attention! Never turn on your windshield wipers if they are frozen to the glass. This may bend the arms or burn out the drive motor. In cold weather, first use a defroster (for example, Liqui Moly Anti-Ice), and then carefully separate the brushes with your hands.

Where to buy wipers for Tiida C11: verified stores and prices

Buy windshield wiper blades for Nissan Tiida C11 possible in the following places:

Store	Original (Nissan)	Premium analogues (Bosch/Valeo)	Budget analogues (SWF/Champion)
Official dealer Nissan	2 800–3 500 ₽	—	—
Exist.ru	2 300–2 900 ₽	1 800–2 400 ₽	900–1 300 ₽
Autodoc	2 500–3 100 ₽	1 700–2 200 ₽	800–1 200 ₽
Wildberries/Ozon	—	1 500–2 000 ₽	700–1 100 ₽

When purchasing online, pay attention to:

• 📦 Availability guarantees (for official sellers - from 6 months).
• 📏 Note exact dimensions in the description (sometimes sellers round up values).
• 🚗 Compatible with Tiida C11 (must be indicated in the product card).

If you buy wipers from an offline store, take an old brush with you for comparison. Some brands (eg HEYNER) supply brushes with adjustable length, but Tiida C11 this is not always appropriate due to the specific shape of the windshield.

FAQ: Frequently asked questions about windshield wipers Nissan Tiida C11

Is it possible to install wipers longer than 22" on the driver's side?

No, this will lead to the brush clinging to the plastic parts of the body at maximum deflection. Maximum allowable size - 22" (56 cm). If you need better cleaning, choose frameless models with improved aerodynamics (e.g. Bosch Aerotwin).

Which wiper brand is the most durable for Tiida C11?

According to owners, they last the longest:

1. Valeo Silencio X-TRM - up to 2 years with moderate use.
2. Bosch Aerotwin — 1.5–2 years, but sensitive to frost.
3. Denso Hybrid - a good option for regions with frequent precipitation.

Budget brands (SWF, Champion) usually lasts for 6–12 months.

What should I do if my wipers leave streaks after replacement?

Causes and solutions:

• Greasy glass - clean it isopropyl alcohol.
• Incorrect installation — check whether the brush lies evenly.
• Rubber defect — return the brushes under warranty.
• Glass wear — if there are microcracks, polishing will help.

Will wipers from Nissan Note fit Tiida C11?

Partially. The front brush sizes are the same (22" and 18"), but the mounting may vary. On Note first generation used U-hook, and on the second - bayonet. Before purchasing, check the year of manufacture Note and compare the mounts.

How often do you need to change the rear wiper on Tiida C11?

The rear wiper wears out more slowly than the front ones, as it is used less often. On average it is enough for 1.5–2 years. However, if you frequently drive on dirt roads or in rainy climates, check the condition of your tires every 6 months. Signs of wear: creaking, streaks, incomplete cleaning of the glass.