Replacing wipers with Nissan Tiida 2008 is a challenge that every owner faces. Over time, the rubber of the brushes loses its elasticity and begins to “rattle” on the glass or leave streaks, impairing visibility in the rain. But before buying new wipers, you need to know their exact dimensions - an error of even 5 cm can lead to a poor fit, squeaking or damage to the windshield.

In this article we have collected current data on wiper sizes for all bodies Tiida 2008 model year (including restyled versions), original articles Nissan and proven analogues. You will also find step-by-step instructions for replacement, tips on choosing frameless or frame blades, and answers to frequently asked questions - for example, is it possible to install wipers longer than standard ones and what the consequences are.

The material was prepared taking into account technical documentation Nissan and car service experience, so you will get Exact dimensions for driver and passenger sides, including rare heated versions. If your Tiida has been restyled or has a non-standard configuration - check the data using the VIN code (read how to do this below).

Official wiper sizes for Nissan Tiida 2008

Standard wiper sizes for Nissan Tiida 2008 depend on the body type: sedan (C11) and hatchback (C10) have different brush lengths. Here are the exact data from the spare parts catalog Nissan:

Body type Driver's side (cm) Passenger side (cm) Rear wiper (cm)
Sedan (C11) 60 40 —
Hatchback (C10) 60 40 30
Restyling 2010+ (all bodies) 60 42 30 (hatchback)

⚠️ Attention: On some versions Tiida with option heated wipers (code B10 included) the size of the passenger brush can be 42 cm instead of 40 cm. This is due to the modified mount. To accurately determine the size, measure your old wipers or check by VIN through a service Nissan Parts.

Also keep in mind that frameless wipers (For example, Bosch Aerotwin or Denso Flat Blade) may have different length markings due to fastening features. In this case, focus on actual length of the rubber part, and not the total length of the plastic case.

📊 What type of wipers do you prefer?
  • Frame (classic)
  • Frameless (flat)
  • Hybrid
  • I don't know what to choose

Original articles and best analogues

Original wipers Nissan for Tiida 2008 are supplied under the article numbers:

  • 🔧 Driver's wiper (60 cm): 28560-4M000 or 28560-4M00A (heated)
  • 🔧 Passenger wiper (40/42 cm): 28561-4M000 / 28561-4M025
  • 🔄 Rear wiper (30 cm, hatchback): 28580-4M000

The cost of original brushes in official dealers Nissan ranges from 1,500 to 2,500 rubles per set. However, many owners choose analogues from trusted brands, which often surpass the original in durability. Here are the best options:

Brand Model Size(cm) Type Average price (RUB)
Bosch Aerotwin A330H 60/40 Frameless 1 200
Denso Flat Blade DF-012 60/42 Frameless 1 400
Valeo Silencio X-TRM 60/40 Hybrid 900
HELLA RainMaster 60/42 Frame 700

💡 Advice: When choosing analogues, pay attention to fastening type. U Nissan Tiida 2008 used mount U-hook (9x3 mm) or Side Pin (22mm) - this is indicated on the back of the original wipers. If you buy a brush with an incompatible mount, you will have to use adapters, which reduces reliability.

💡

Before purchasing, check compatibility according to the manufacturer's catalog. For example, on the site Bosch There is a selection tool by car model: bosch-automotive.com.

How to determine the size of wipers if there is no data

If you are not sure about the sizes or your Tiida has a non-standard configuration, there are three reliable ways to find out the exact length:

  1. Measure old wipers.

    Take a tape measure or ruler and measure length of rubber part (without plastic fastening). Measure along the outer edge of the arc. If the blade is worn, add 1-2 cm to the result - new wipers should be slightly longer for a better fit.

  2. Check by VIN code.

    VIN of your Tiida can be found on a plate under the hood or in documents. Enter it on the sites:

    Look for the section in the results Wiper Blade Size.

  3. Comparison with analogues.

    Nissan Tiida 2008 built on a platform Renault-Nissan B, so wipers can fit from the following models:

    • 🚗 Renault Megane II (2002–2008)
    • 🚗 Samsung SM3 (Korean version Tiida)
    • 🚗 Nissan Note E11 (2006–2012)

What to do if the wipers don't fit?

If after installation the brushes are too long or short:

- Long wipers (for example, 65 cm instead of 60 cm) will cling to the pillars or the edge of the hood, which will lead to breakage of the mechanism or scratches on the paint.

- Short wipers (for example, 38 cm instead of 40 cm) will leave uncleaned areas on the glass, impairing visibility.

In both cases, return the brushes to the seller and select the correct size. Some stores (eg. Exist.ru or Autodoc) allow you to exchange goods within 14 days even after installation, if the packaging is intact.

Step-by-step instructions for replacing wipers

Replacing wipers with Nissan Tiida 2008 takes no more than 10 minutes and requires no tools. Follow these instructions to avoid errors:

New wipers of the right size

Clean rag or napkin

Glass cleaning spray (optional)

Gloves (to avoid getting your hands dirty)

-->

  1. Preparation.

    Park the car on a level surface and turn off the ignition. Raise the wipers to a vertical position (perpendicular to the glass) - to do this, turn them on for 1-2 seconds, then turn them off when they are at the highest point.

  2. Removing the old brush.

    Click on plastic retainer at the place where the wiper is attached to the lever (it is located on the side or bottom). Pull the brush down along the lever while holding the latch. If the mount Side Pin, you may need to move the brush to the side.

    ⚠️ Attention: Do not pull the brush perpendicular to the lever - this may bend the metal bracket or break the plastic adapter.
  3. Installing a new brush.

    Compare the attachment of the new brush with the old one. If they match, move it onto the lever until it clicks. For fastenings U-hook You may need to squeeze the adapter's plastic "tendrils" slightly. Make sure the brush is locked in place and does not wobble.

  4. Check.

    Lower the wipers onto the glass and turn them on at minimum speed. See if there is:

    • 🔊 Creaks or rattles
    • 💧 Stains or uncleaned areas
    • 🚫 Touching body parts

If there are problems, check the correct installation or size of the brushes.

💡

After replacing the wipers, be sure to clean the glass from the protective film (if it was on the new blades) and apply hydrophobic coating - this will extend the life of the tires and improve visibility in the rain.

Common mistakes when choosing and replacing wipers

Even experienced drivers sometimes make mistakes that lead to premature wiper wear or vehicle damage. Here are the most common:

  • 🔄 Ignoring the installation side.

    Windshield wipers for the driver and passenger sides often have different lengths and mounting shapes. Installing it the other way around will result in poor fit and rapid wear.

  • 🛠️ Using incompatible adapters.

    Some universal brushes come with a set of adapters. If you choose the wrong one, the wiper will hang loose or not lock at all.

  • ❄️ Saving on winter wipers.

    In cold weather, ordinary brushes freeze to the glass, and the rubber hardens. For Tiida winter models with a protective cover are suitable (for example, Bosch Winter or Valeo Snow).

  • 🚿 Washing glass with active wipers.

    This reduces the service life of rubber by 2–3 times. Always turn on the washer before the work of the wipers, and not at the same time.

🔧 Expert advice: If after replacement the wipers “bounce” at high speed, the reason may be:

- Wear of the wiper trapezoid (needs renovation).

- Sand getting under the tires (clean brushes with alcohol).

- Poor quality tires (replace with branded analogues).

How to extend the life of wipers: care and storage

Average service life of wipers - 6–12 months, but with proper care they can be used for up to 2 years. Here's what experts recommend:

  • 🧼 Regular cleaning.

    Every 2 weeks, wipe the rubber with a damp cloth and soapy water. This removes microparticles of sand and resin that scratch the glass.

  • 🌞 UV protection.

    Rubber will dry out in direct sunlight. Use protective spray (For example, 3M Rubber Care) or park in the shade.

  • ❄️ Preparing for winter.

    Treat your tires before frost silicone grease (not to be confused with WD-40!). This will prevent freezing. Also check the anti-freeze level - it should be designed for temperatures below -25°C.

  • 🔧 Checking tension.

    Once a month, lift the wipers and see if there is any play in the mounting. If the lever is loose, tighten the nut with a wrench 10 mm.

⚠️ Attention: Never turn on your wipers if they are frozen to the glass! This may tear the rubber or bend the lever. Instead:

  1. Start the engine and turn on the defroster.
  2. Pour over the ice warm (not hot!) water or anti-freeze.
  3. Gently pry the wiper out with a plastic spatula.

FAQ: Answers to frequently asked questions

Is it possible to install wipers longer than standard ones?

No, this is fraught:

  • 🚫 The brush touches the pillars or the edge of the hood (scratches will appear).
  • 🔊 Increased noise and vibration at speeds over 80 km/h.
  • ⚡ Risk of breakdown of the wiper motor due to increased load.

Maximum permissible deviation - +2 cm (for example, 62 cm instead of 60 cm), but only if the brush is flexible and does not cling to the body.

What is the difference between wipers for a sedan and a hatchback? Tiida?

The main difference is the presence rear wiper for the hatchback (30 cm). The dimensions of the front blades are the same (60/40 or 60/42 cm), but the hatchback may have a different bend of the wiper arm, so the original blades for the sedan do not always fit perfectly.

How often should wipers be changed?

Recommended interval - every 6–12 months, but look for signs of wear:

  • 🔊 Creaking or rattling during operation.
  • 💧 Stains or stripes on the glass.
  • 🧊 Cracks or peeling of rubber.

In regions with frequent rain or sandstorms, replacement will have to be done more often.

Is it possible to restore old wipers?

Partially yes. If the rubber is worn but not torn:

  1. Clean it up isopropyl alcohol.
  2. Process silicone grease (not technical silicone!).
  3. Swipe over the rubber 1000 grit sandpaper (carefully so as not to damage).

This will extend the life of the brushes by 1–2 months, but will not replace a full replacement.

Where to buy wipers for Tiida cheaper?

Compare prices on these sites (as of 2026):

  • 🛒 Exist.ru — originals and analogues with discounts up to 30%.
  • 🛒 Autodoc — free delivery from RUB 1,500.
  • 🛒 I'll take it! — there are often promotions on brands Bosch And Denso.
  • 🛒 Local stores (for example, Auto49 or AutoSpetsCenter) - you can touch it before buying.

Average savings when purchasing online - 15–25% compared to offline stores.