Selection of rims for Nissan Qashqai J11 (second generation, produced from 2013 to 2021) is a task that requires attention to technical nuances. An error in the parameters can lead not only to visual disharmony, but also to premature wear of the suspension, increased load on wheel bearings or even ABS system failure. In this article we will look at the official wheel sizes for all trim levels. Qashqai J11, as well as permissible deviations for tuning - taking into account the experience of the owners and the manufacturer’s recommendations.
A special feature of the model is the variety of engines (from 1.2-liter turbo to 2.0-liter diesel) and trim levels, which affects the factory parameters of the wheels. For example, versions with all-wheel drive (4WD) were often equipped with wheels with a shorter offset (ET) to compensate for the increased track. We analyzed data from service manuals Nissan, parts catalogs and crash test reports to provide up-to-date information - without speculation or outdated information.
Official wheel sizes for Nissan Qashqai J11 by trim level
The manufacturer installed it on Qashqai J11 discs of three main diameters: 16", 17" And 19". In this case, the key parameters are PCD (loose talk), ET (departure) and DIA (diameter of the central hole) - remained unchanged for all versions. The exception is special editions, for example, Nissan Qashqai J11 N-Connecta or Tekna, where discs with a unique design but the same technical characteristics could be used.
The table below shows the factory parameters of disks for the most common configurations. Please note: data is current for models 2013–2021 model years, including restyled versions (2017–2021). For an accurate selection, always check the sticker on the driver's door pillar or data from VIN decoder.
| Equipment | Diameter (inches) | Width (inches) | PCD (bolt pattern) | ET (reach, mm) | DIA (mm) |
|---|---|---|---|---|---|
| Visia, Acenta (basic) | 16 | 6.5J | 5×114.3 | 45 | 66.1 |
| N-Connecta, Tekna (mid/top) | 17 | 7.0J | 5×114.3 | 40–45 | 66.1 |
| Tekna+, Limited Edition (premium) | 19 | 7.5J | 5×114.3 | 38–40 | 66.1 |
| 4WD (all-wheel drive) | 16–17 | 6.5J–7.0J | 5×114.3 | 35–40 | 66.1 |
Important: Wheels with an ET offset < 35 mm or > 45 mm may cause contact with the suspension components or arches when the vehicle is fully loaded or on uneven roads. Tests confirm this ADAC (2019), where Qashqai J11 with non-standard disks ET30 showed an increase in shock absorber wear by 22% after 20,000 km.
Bolt pattern (PCD) and center hole (DIA): why you can’t go wrong
Parameter PCD 5×114.3 means that on the hub Nissan Qashqai J11 located 5 mounting holes, and the diameter of the circle on which they are located is equal to 114.3 mm. Attempt to use disks with a different PCD (e.g., 5×112 or 5×120) will lead to the impossibility of correct installation - the bolts simply will not line up with the holes. Moreover, even a minimal deviation of 1–2 mm will cause wheel runout, which is fraught with:
- 🔧 Vibration on the steering wheel at speeds over 80 km/h;
- 🚗 Uneven tire wear (especially along the inner edge);
- ⚠️ Damage to wheel bearings due to uneven load.
Central hole (DIA 66.1 mm) is also critical: if its diameter is smaller, the disc will not physically fit onto the hub; if more, you will need centering rings (but their use is not recommended for long-term use). At service centers Nissan note that more than 60% of vibration calls are related specifically to incorrect DIA or lack of centering rings.
- 16 inches
- 17 inches
- 19 inches
- Other (please specify in comments)
Tolerable deviations: what can be changed without risk
Many owners Qashqai J11 tend to install larger diameter wheels to improve appearance or a smaller offset to widen the track. However, such modifications have severe limitations. Below are maximum permissible deviations, confirmed by engineers Nissan and tests TÜV (Germany):
- 📏 Diameter: ±1 inch from stock (for example, replacing 16" by 17" or 19" by 18");
- 🔄 Departure (ET): ±5 mm from factory (for example,
ET45→ET40); - 🔩 Width: ±0.5 inches (e.g.
6.5J→7.0J).
Exceeding these values will require modifications: for example, installation spacers (to reduce overhang) or rolling out the arches (to increase the diameter). In this case, any changes must be accompanied by adjustments to the bus parameters to save total wheel diameter (otherwise the speedometer will lie and the ABS will malfunction).
⚠️ Attention: Installing discs with offset ET < 35 mm for front-wheel drive versions Qashqai J11 leads to an increase in the load on the wheel bearings by 30–40%. This is confirmed by data from service centers Nissan in Russia (2020–2023), where such cases are recorded as “warranty exceptions.”
What happens if you install disks with PCD 5x112?
Wheels with a 5x112 bolt pattern will not physically fit the Qashqai J11 hub (5x114.3). Even if you use adapter studs or adapters, this will lead to uneven load distribution, wheel runout and the risk of the disc coming off at high speed. In Germany such modifications are prohibited by law (§30 StVZO).
How to choose non-standard wheels: step-by-step instructions
If you decide to deviate from the factory settings, follow this algorithm to avoid errors:
- Check current settings on the driver's door sticker or
VIN decoder(for example, on the website Nissan Russia). - Use the compatibility calculator (we recommend WillTheyFit or TireSizeCalculator).
- Check the database of acceptable sizes for Qashqai J11 (see table above).
- Consult a tire shopspecializing in Nissan (for example, networks Koleso-Darom or Shina-Service).
Example: if your Qashqai J11 has wheels as standard 16×6.5J ET45, then you can safely install:
- 🔵
17×7.0J ET40(with tire215/60 R17); - 🔵
18×7.5J ET38(with tire225/55 R18and rolling out arches).
☑️ Check before purchasing non-standard disks
Top 5 mistakes when choosing wheels for Qashqai J11
Forum analysis (Drive2, Qashqai-Club.ru) and reports from service centers showed that the owners Qashqai J11 The most common mistakes made are:
- Ignore departure (ET). For example, installing disks with
ET30instead ofET45leads to “bulging” of the wheels and friction against the fender liners when turning. - Failure to comply with the diameter of the central hole. Discs with
DIA 72.6 mm(from Volkswagen) will not fit without adapters. - Incorrect tire selection. For example, replacement
215/65 R16on235/50 R17without taking into account changes in the outer diameter of the wheel. - Using cheap replicas. Discs without certification TÜV or JWL often have an imbalance, which leads to vibrations.
- Neglect of balancing. Even original wheels require balancing after installing new tires.
To avoid these problems, use only certified discs from trusted brands: BBS, OZ Racing, Enkei or original Nissan. The model is often recommended on forums Nissan 40501-4M00A (17") as the optimal price/quality ratio.
Before purchasing discs, check them for a certificate of conformity UNECE (labeling E with a number in a circle on the back). This guarantees passing crash tests and the absence of hidden defects.
The influence of disc size on handling and fuel consumption
Increasing the diameter of the rims (and, as a result, reducing the tire profile) affects several key characteristics of the car:
| Parameter | 16" (standard) | 17" | 19" |
|---|---|---|---|
| Fuel consumption (city) | Basic | +0.3–0.5 l/100 km | +0.7–1.0 l/100 km |
| Suspension stiffness | Soft | Average | Hard (noticeable unevenness) |
| Braking distance (dry asphalt) | Basic | −1–2 m (due to better grip) | −2–3 m (but risk of aquaplaning) |
Log tests "Behind the Wheel" (2018) showed that the transition from 16" to 19" wheels increases load on shock absorbers by 15–20%, reducing their resource from 100,000 to 70,000–80,000 km. At the same time, the improvement in braking properties is only 5–7%, which does not always justify the cost of replacement.
⚠️ Attention: If you are exploiting Qashqai J11 mainly on dirt roads or in Russian winter conditions, discs with a diameter 19" with low profile tires (225/45 R19) significantly increase the risk of wheel damage or tire puncture. The optimal choice for such conditions is16"or17"with high profile tires (215/65 R16).
Where to buy wheels for Nissan Qashqai J11: proven options
When purchasing discs for Qashqai J11 We recommend contacting official dealers or trusted online stores. Below is a list of reliable sources with a guarantee of authenticity:
- 🏢 Official dealers Nissan - original discs with a 2-year warranty (for example, Nissan Center Moscow or Nissan Petersburg).
- 🛒 Online stores:
- Kolesa-Darom.ru (wide range, there is a filter by
PCD 5×114.3); - ShinaGuide.ru (selection by
VINtaking into account the configuration); - Exist.ru (wholesale prices, but certificate verification required).
- Kolesa-Darom.ru (wide range, there is a filter by
- 🔧 Tire shops with their own wheel database (For example, Pit Stop or TireMaster).
The cost of original disks for Qashqai J11 varies:
- 💰
16": RUB 8,000–12,000/piece; - 💰
17": 10,000–15,000 rub./piece; - 💰
19": RUB 18,000–25,000/piece.
When purchasing used drives, be sure to check:
- 🔍 No cracks (especially around the mounting holes);
- 🔍 Balancing (the disk should not have a visible beat when scrolling);
- 🔍 Condition of the paintwork (corrosion impairs strength).
Buy discs only with a complete set of documentation: certificate of conformity, warranty card and receipt. This will protect you from counterfeits and allow you to return the product if it is defective.
FAQ: Frequently asked questions about wheels for Nissan Qashqai J11
Is it possible to install 18" wheels on a Qashqai J11 if the standard ones are 17"?
Yes, but with reservations:
- Departure (
ET) must be within38–42 mm; - Disc width - no more
7.5J; - You will need to choose a tire with a smaller profile (for example,
225/50 R18) to maintain the outer diameter of the wheel; - You may have to roll out the arches (depending on the width of the tire).
We recommend that you first consult with a suspension specialist, since increasing the disc diameter increases the load on the shock absorbers.
What wheels fit other Nissan models?
Drives from the following models Nissan compatible with Qashqai J11 by bolt pattern (PCD 5×114.3) and DIA:
- Nissan X-Trail T32 (2013–2021);
- Nissan Juke F15/F16 (but departure check required);
- Nissan Rogue (American version X-Trail).
However departure (ET) And width may vary! For example, disks from X-Trail often have ET35which is too little for Qashqai J11 with front-wheel drive.
What should I do if vibration appears after replacing the disks?
Vibration at speeds of 80–120 km/h is usually associated with:
- Incorrect balancing (wheels need to be rebalanced);
- Mismatch
PCDorDIA(check the centering rings); - Damage to the disc (cracks, deformation);
- Worn wheel bearing (check play).
If the problem persists, contact a service center to diagnose the suspension - you may need to replace the shock absorbers or silent blocks.
Is it possible to drive rims with a different PCD using adapter studs?
Absolutely not! Adapter studs or adapters for change PCD:
- The wheel alignment is disturbed;
- Increase the risk of disc separation at high speed;
- Lead to uneven wear of wheel bearings;
- Not certified TÜV or GOST R.
In Germany and EU countries such modifications are prohibited by law and are grounds for refusal of technical inspection.
What is the maximum diameter of rims that can be installed on a Qashqai J11 without modifications?
Without rolling out the arches or changing the suspension, the maximum safe diameter is 18" with parameters:
- Width:
7.5J; - Departure:
ET38–40; - Tire:
225/50 R18or235/45 R18.
Installation 19" disks will be required:
- Rolling out the front and rear arches;
- Use of tires with a profile no higher
40(For example,225/40 R19); - Checking clearances when the vehicle is fully loaded.