Car owners Nissan Wingroad are often faced with the need to replace wheel rims, whether for seasonal re-shoes or the desire to install more stylish alloy options. The key parameter in this case is not the appearance, but the exact correspondence of the technical characteristics of the fastener and the geometry of the wheel to the car hub.
An incorrectly selected disc can lead to steering wheel wobble, accelerated bearing wear, and even loss of the wheel while driving. Therefore, before purchasing, you need to clearly know which one Nissan Wingroad bolt pattern typical for your year of manufacture and configuration.
In this article, we'll break down all the technical details, from the number of holes to the diameter of the center hole (DIA), so you can safely and competently upgrade your station wagon's set of wheels.
Basic bolt pattern parameters for Nissan Wingroad
The most important factor when choosing discs is the drill bit, or PCD. For model Nissan Wingroad this parameter is practically unchanged throughout the entire production period. The standard value is 4x114.3. This means that there are 4 mounting holes on the disk, the diameter of the circle passing through their centers is 114.3 millimeters.
Ignoring this parameter will result in the disc simply not fitting onto the hub or sitting crookedly, even if you try to tighten the bolts with force. In such cases, you have to use spacers, which is extremely undesirable for the suspension.
In addition to drilling, it is critical to pay attention to center hole diameter (DIA or CO). For Nissan Wingroad The factory standard is 66.1 mm. If you buy universal wheels with a large hole, you will definitely need centering rings to eliminate vibrations.
⚠️ Attention: Using disks with a smaller central hole diameter than 66.1 mm is physically impossible without turning the hub, which is strictly prohibited and unsafe.
- PCD (bolt pattern): 4x114.3 - the only standard for this model.
- Center hole (DIA): strictly
66.1 mm. - Number of mounting bolts: 4 pieces.
Wheel diameter, width and offset
The choice of rim width and offset (ET) affects the car's cornering behavior and the load on the suspension components. For Nissan Wingroad Factory recommendations typically range from 5.5J to 6.5J. The width in inches determines how wide a tire you can fit.
Overhang (ET) is the distance from the mounting surface of the disc to the center line of symmetry of the rim. Standard value for Nissan Wingroad usually ranges from 35 to 45 mm. Increasing the offset can cause the wheel to rub against the suspension components when turning the steering wheel.
Decreasing offset (negative ET) moves the wheel outward, widening the track. This improves stability, but dramatically increases the load on the wheel bearings. The maximum permissible offset deviation is no more than 5 mm less than the factory value.
When selecting summer and winter tires, wheels of a smaller diameter, for example, R14 or R15, are often used to reduce the cost of a set of tires and improve comfort on bad roads.
- Recommended rim width:
5.5J - 6.5J. - Standard Reach (ET):
35 - 45mm. - Wheel diameters: from 14 to 16 inches (depending on configuration).
- Cast (Alloy)
- Steel
- Forged
- Wheels with spikes
Fasteners: bolts and nuts
After choosing a disk, you should not forget about the fasteners. On Nissan Wingroad bolts with metric threads are used M12x1.25. This means that the bolt diameter is 12 mm and the thread pitch is 1.25 mm. Using bolts with a different thread pitch may lead to stripping of the threads in the hub.
The length of the bolt also matters. If you are installing spacers or wheels with a thick mounting flange, standard bolts may not provide the necessary engagement. The minimum number of engaged threads must be at least 7-8.
The shape of the bolt seat (cone) must match the disk. Usually this 60 degree cone. If the shape does not match (for example, spherical), the wheel may unscrew when moving.
☑️ Checking fasteners
Often owners try to use bolts from other models Nissan, for example, from Almera or Primera. Although many parameters are the same, the length of the threaded portion may vary, creating the risk of loosening.
- Thread type: M12x1.25 (metric).
- Bolt seat shape:
60° cone. - Recommended tightening torque:
108 - 127 Nm.
Why are non-standard bolts dangerous?
If the bolt is too short, it will not be able to generate enough clamping force. If it's too long, it can jam against the brake mechanism or hub without tightening all the way, causing the wheel to spin out while driving.
Seasonal features and tire sizes
In addition to the wheels, it is important to choose the right tires that will match the bolt pattern and wheel arch dimensions. For Nissan Wingroad most popular sizes 185/65 R15 and 195/65 R15. These dimensions strike a balance between comfort and handling.
When switching to winter tires, wheels of a smaller diameter, for example, R14, with a higher tire profile are often used. This allows you to save on a set of tires and improves shock absorption on bumps. However, the width of the tire should not exceed the permissible values, so as not to touch the arches.
When purchasing a set of discs for the winter, always check that the kit includes plugs for the nipple caps so that dirt does not get inside the disc.
- Popular tire size:
185/65 R15or195/65 R15. - Allowable minimum diameter:
R14(for winter set). - Maximum tire width:
205 mm(with caution).
Choosing the right tire size is just as important as choosing the wheel - a discrepancy in the profile can lead to friction against the fender liners and body when the car is fully loaded.
Nissan Wingroad technical specifications table
For ease of selection, we have collected all the main parameters in one summary table. This data is relevant for most modifications Nissan Wingroad, including versions with turbo engines and conventionally aspirated engines.
| Parameter | Meaning | Note |
|---|---|---|
| PCD (drilling) | 4x114.3 | Standard for all model years |
| Center Hole (DIA) | 66.1 mm | Requires centering rings if different |
| Bolt thread | M12x1.25 | Thread pitch 1.25 mm |
| Departure (ET) | 35-45 mm | Tolerance ±5 mm |
| Fasteners | 4 bolts/nuts | 60 degree cone |
Typical mistakes when changing wheels
Many car owners make the mistake of trying to “fit” unsuitable rims using spacers or a sledgehammer. This is a gross violation of safety regulations. Even if the disc is firmly seated on the hub, it will not center correctly, resulting in vibration at high speeds.
Another common problem is using bolts with the wrong seat shape. Alloy wheels often use a cone, while some steel wheels often use a sphere. Mixing these types of fasteners is unacceptable, as this violates the geometry of the clamp.
Never tighten bolts by weight or using extensions without a torque wrench. Excessive force can stretch the bolt and it will burst the next time you drive, and insufficient force will cause the wheel to unscrew.
⚠️ Warning: Never attempt to install a disc that does not fit onto the hub without force. This is a sign that the center hole is misaligned and the wheel will not be secured securely.
Why does the wheel vibrate after replacement?
The reasons may be imbalance, a crooked disk, but most often the problem lies in improper centering (lack of rings) or the use of worn bolts.
Conclusion and safety recommendations
Selection of wheels for Nissan Wingroad - a task that requires attention to technical details. Compliance with parameters bolt pattern 4x114.3 and a central center diameter of 66.1 mm is a prerequisite for safe operation.
If you are in doubt about the compatibility of a rim, it is best to consult with a specialist at a tire store or look at the markings on the inside of the rim itself. Manufacturers always specify PCD, DIA and ET.
Remember that skimping on the quality of fasteners or choosing the wrong discs can cost you not only money on suspension repairs, but also your health. Check the bolts for tightness regularly, especially after your first ride on new wheels.
What is the bolt pattern of the Nissan Wingroad?
The Nissan Wingroad has a bolt pattern of 4x114.3 mm. This means 4 holes on a circle with a diameter of 114.3 mm.
What center hole diameter (DIA) does the Wingroad need?
The central hole must be strictly 66.1 mm. If the disc has a larger hole, adapter rings must be used.
Which bolts are suitable for Nissan Wingroad?
Bolts with M12x1.25 thread and 60 degree cone are used. The length of the bolt must correspond to the thickness of the disc.
Is it possible to install wheels with an offset of ET40 if the standard one is ET38?
Yes, a difference of 2mm is within the acceptable range. Standard offset usually ranges from 35 to 45 mm.