Nissan Sunny is a legendary compact car that has gained popularity due to its reliability and ease of maintenance. However, when choosing new wheels or tires, owners are often faced with the question: which bolt pattern is suitable for a particular model? An error in the parameters can lead to vibrations, accelerated wear of the suspension, or even an emergency.

In this article we will analyze in detail all the bolt pattern parameters for Nissan Sunny different generations (N14, N15, N16, N17), including PCD, departure (ET), center hole diameter (DIA) And hub diameter. You will also find a disk compatibility table, selection tips and answers to frequently asked questions.

What is bolt pattern and why is it important for Nissan Sunny?

Bolt pattern (or PCD — Pitch Circle Diameter) is the diameter of the circle on which the wheel rim mounting holes are located. For Nissan Sunny this parameter is critical, since incorrect selection can lead to:

  • 🔧 Uneven wear tires and suspension due to a shift in the center of gravity.
  • 🚗 Vibrations on the steering wheel when driving at speeds over 80 km/h.
  • ⚠️ Unscrewing nuts while driving (in extreme cases).
  • 🔄 Inability to pass inspection due to parameter mismatch.

Except PCD, for Sunny Other parameters are also important:

  • ET (departure) — the distance from the mating plane of the disk to its center. Deviation of more than ±5 mm may result in friction between the disc and the caliper or arch.
  • DIA - diameter of the central hole. If it is smaller than the hub, the disc will not seat; if more, centering rings will be required.
  • Hub diameter - must match the space on the disk.
⚠️ Attention: On Nissan Sunny N16 (2000–2006) sometimes installed discs from Nissan Almera N16, but their bolt pattern is identical only for versions with a motor QR20DE. For GA16DE VIN check required!

Bolt pattern table Nissan Sunny by generation

Below are the official parameters for all generations Sunny, produced in Russia and Europe. The data is relevant for sedans and hatchbacks, including restyled versions.

Generation Years of manufacture PCD (bolt pattern) ET (reach), mm DIA (center hole), mm Hub diameter, mm Fastener thread
Nissan Sunny N14 1990–1995 4×100 35–45 59.1 54.1 M12×1.25
Nissan Sunny N15 1995–2000 4×100 35–45 59.1 54.1 M12×1.25
Nissan Sunny N16 (sedan/hatchback) 2000–2006 4×114.3 35–50 66.1 60.1 M12×1.25
Nissan Sunny N17 (for Asian markets) 2010–2020 4×100 35–45 60.1 56.1 M12×1.25

Important: Nissan Sunny N16 with motor QR20DE has a bolt pattern of 4×114.3, while versions with GA16DE - 4x100. Check the data on the VIN or the nameplate on the door pillar!

📊 What generation of Nissan Sunny do you have?
  • N14 (1990–1995)
  • N15 (1995–2000)
  • N16 (2000–2006)
  • N17 (2010–2020)
  • Other

How to measure the bolt pattern yourself Nissan Sunny?

If you are not sure about the parameters of your car, you can measure the bolt pattern yourself. You will need:

  • 📏 Caliper or ruler.
  • 🔧 Wheel removal key.
  • 📝 Paper and pen for notes.

Step 1: Removing the wheel

Raise the car with a jack, remove the wheel and clean the hub from dirt. The mounting holes must be clearly visible.

Step 2: PCD Measurement

For discs with 4 holes (like Sunny) Measure the distance between the centers of two opposite holes. This will be the PCD value. For example, if the distance is 100 mm, the bolt pattern is 4x100.

Step 3: Departure Check (ET)

Place the disc on a flat surface, place a ruler on top and measure the distance from the plane of contact to the edge of the rim. Then turn the disk over and measure again. Departure is calculated using the formula:

ET = (A + B)/2 – C

where A And B - measurements on both sides, C — disk width.

⚠️ Attention: On Nissan Sunny N16 With a bolt pattern of 4×114.3, you cannot install 4×100 wheels without adapters! This will lead to uneven tightening of nuts and the risk of the wheel coming off.

Remove the wheel and clean the hub|Check the number of mounting holes|Measure the distance between opposite holes|Check the data with the compatibility table-->

Drive compatibility: which models are suitable for Sunny?

When selecting disks for Nissan Sunny you can focus on original articles or analogues from other models Nissan And Renault. Below are proven options:

  • 🔄 Original wheels:
    • 40500-4M000 (N14, 14", 4×100, ET45)
    • 40500-6M000 (N16, 15", 4×114.3, ET40)
  • 🔧 Analogues from other models:
    • Discs from Nissan Almera N16 (only for Sunny N16 with PCD 4×114.3).
    • Discs from Renault Megane 1 (4×100, ET38–45).
    • Discs from Micra K12 (only for Sunny N17).

Selection example: For Nissan Sunny N15 1998 with motor GA16DE suitable discs:

  • Size: 14×5.5J or 15×6J.
  • PCD: 4×100.
  • ET: 38–45 mm.
  • DIA: 59.1 mm.
💡

When buying used wheels, check them for runout! Place the disc on a flat surface and spin it - if there is play or a figure of eight, refuse to purchase.

Common mistakes when choosing disks for Sunny and how to avoid them

Many owners Nissan Sunny encounter problems after installing the wrong drives. Here are the most common mistakes:

  1. Ignoring departure (ET).

    Installing ET 30 rims instead of the recommended 40mm will result in the wheel protruding beyond the arch. This is dangerous when turning and can damage the fender liners.

  2. DIA mismatch.

    If the center hole of the disk is larger than the hub, the wheel will only be mounted with bolts, which will lead to beating And uneven wear.

  3. Use of spacers.

    Spacers for changing the offset reduce the reliability of fastening and can cause wheel separation during emergency braking.

⚠️ Attention: On Sunny N16 with a bolt pattern of 4×114.3 you cannot install wheels from Mitsubishi Lancer 9 (despite the same PCD), since they have different hub diameter (60.1 vs 67.1 mm).
What happens if you install disks with the wrong PCD?

Even if the disc physically seats on the hub, the mounting bolts will not be tightened evenly. This will result in:

- Vibrations on the steering wheel at speeds >60 km/h.

- Accelerated wear of wheel bearings.

- Risk of loosening the nuts while driving (especially on uneven roads).

In the worst case, the wheel may come off while driving!

How to choose tires for rims Nissan Sunny?

Choosing the right tires is just as important as choosing the wheels. For Sunny The following sizes are recommended:

Generation Disc diameter Recommended tire size Valid Alternative
N14/N15 14" 175/70 R14 185/65 R14
N16 15" 195/60 R15 185/65 R15
N17 15–16" 185/65 R15 195/55 R16

When choosing tires, consider:

  • 📏 Profile width should not exceed the recommended value by more than 10%. For example, instead of 175/70 R14 you can put 185/65 R14, but 195/60 R14 is already risky.
  • ❄️ Seasonality: for winter, choose tires with a speed index of at least T (up to 190 km/h).
  • 🔧 Load Index must be at least 82–86 (depending on the weight of the car).
💡

For Nissan Sunny N16 with motor QR20DE The optimal tire size is 195/60 R15. This strikes a balance between handling and comfort.

Where to buy wheels and tires for Nissan Sunny?

When purchasing wheels and tires for Sunny We recommend contacting trusted stores:

  • 🏬 Offline stores:
    • Koleso.ru — a wide range of original and analog discs.
    • Shina.ru — frequent promotions on tires of famous brands (Michelin, Continental).
  • 🌍 Online platforms:
    • Kolesa-Darom — used wheels with a guarantee.
    • Ozon — new wheels and tires with delivery.

When purchasing used drives, be sure to check:

  1. No cracks or dents on the rim.
  2. Condition of the threads of the mounting holes.
  3. The geometry of the disk (is there a “figure eight”)?
⚠️ Attention: On Nissan Sunny N17 (2010–2020) often install discs from Renault Logan (4x100), but their offset (ET) may vary. Always check your parameters!

FAQ: Frequently asked questions about bolt pattern Nissan Sunny

Is it possible to install 4x114.3 disks on Sunny N15 (original 4×100)?

No, this is not possible without adapters. The 4x114.3 bolt pattern is incompatible with the 4x100 - the holes won't line up and the disc won't fit on the hub. The use of adapters reduces safety!

What is the maximum reach (ET) that can be set on Sunny N16?

For Nissan Sunny N16 the permissible ET range is from 35 to 50 mm. Exceeding these values will result in friction between the disc and the caliper or arch.

Will discs fit? Nissan Almera Classic on Sunny N17?

Yes, but only if the bolt pattern matches (4x100). However, check the offset (ET) and center bore diameter (DIA) - they may vary.

Is it possible to increase the diameter of the disks by Sunny N14 from 14" to 15"?

Technically yes, but you will need to choose tires with a smaller profile (for example, 185/60 R15 instead of 175/70 R14). Make sure that the new discs do not touch the caliper!

Where to find the VIN number on Nissan Sunny to check parameters?

The VIN number is located on a plate under the hood (driver's side) or on the door pillar. It can also be found in STS or PTS.