Nissan Presage - a compact minivan, released in 1998–2009, which is still popular due to its practicality and reliability. However, when replacing wheels or tuning, owners are often faced with the question: what is the bolt pattern of this car? An error in choosing parameters can lead to vibrations, premature wear of the suspension or even emergency situations.

In this article we will look at all key bolt pattern parameters for Nissan Presage (body R50), including PCD, Overhang (ET), Center Hole Diameter (DIA) and hub dimensions. You will also find compatibility tables with popular wheel models, tire selection tips, and answers to frequently asked questions. We will pay special attention to the nuances that even experienced car owners often miss.

What is a bolt pattern and why is it important for Nissan Presage

Bolt pattern (or PCD — Pitch Circle Diameter) is the diameter of the circle on which the wheel mounting holes are located. For Nissan Presage this parameter is critical, since incorrect selection can lead to:

  • 🔧 Uneven wear tires and suspension due to a shift in the center of gravity.
  • 🚗 Vibrations at speed over 80 km/h, even if the discs are perfectly balanced.
  • ⚠️ Unscrewing nuts while driving (in extreme cases).
  • 🔄 Inability to install wheels from other Nissan models without adapters.

On Presage R50 used standard for many models Nissan bolt pattern 5×114.3 (5 holes, circle diameter 114.3 mm). However, this is not enough for a safe selection: at least 3 more parameters need to be taken into account.

⚠️ Attention: Even if the disc physically fits onto the hub, this does not guarantee compatibility. For example, incorrect departure (ET) can lead to friction between the wheel and the arch or suspension when the vehicle is fully loaded.

Basic parameters of the Nissan Presage R50 bolt pattern

Below is a table with key dimensions for all modifications Presage (1998–2009). Please note: the parameters are the same for the front and rear axles, but may differ depending on the year of manufacture and equipment.

Parameter Meaning Note
Bolt Pattern (PCD) 5×114.3 Standard on most Nissan minivans of the period
Departure (ET) 35–45 mm Optimal range. ET 35 - for wide rims, ET 45 - for standard ones
Center Hole Diameter (DIA) 66.1 mm Critical for disk alignment. If there is a discrepancy, centering rings are required
Mounting thread M12×1.25 Standard for Nissan. Stud length: 28–30 mm
Hub diameter 100 mm Important for selecting spacers (if required)

Feature Presage - relatively small departure (ET). This means that the discs are “recessed” deeper into the arch, which gives more room for maneuver when tuning. However reduction of ET below 35 mm without modification of the suspension it is fraught with:

  • 🔧 Increased load to the wheel bearings.
  • 🚗 Deterioration in controllability at high speeds.
  • ⚠️ Contact of the tire with body elements when fully loaded.
📊 What type of wheels do you prefer for Nissan Presage?
  • Steel (stamped)
  • Cast (light alloy)
  • Forged
  • Other

Compatible with wheels from other Nissan models

Thanks to standard bolt pattern 5×114.3, disks from Presage suitable for many models Nissan and even other brands (for example, Renault or Infiniti). However, there are nuances:

  • 🔄 Nissan Serena (C24) — full compatibility with PCD and DIA, but offset may vary (ET 40–50).
  • 🔄 Nissan Almera N16 — fits PCD, but DIA = 66.1 mm (like Presage), and offset is usually ET 38–45.
  • ❌ Nissan X-Trail (T30/T31) — the bolt pattern is the same, but DIA = 66.1 mm, and offset ET 35–40. Incompatible without spacers due to different widths of wheel arches.
  • ⚠️ Infiniti QX4 — PCD matches, but DIA = 72.6 mm. Centering rings required.

Before purchasing discs from disassembly or used be sure to check:

☑️ Checking disk compatibility

Done: 0 / 5

If you plan to install disks with long reach (for example, ET 50), this will lead to a narrower track and poor stability. At the same time reduction of ET to 30 mm will require rolling out the arches or installing spacers.

⚠️ Attention: Using spacers thicker than 15 mm without strengthening the hub can lead to deformation of the mounting studs. For Presage The recommended thickness of spacers is no more than 10 mm.

Selection of tires for Nissan Presage: sizes and recommendations

Standard tire sizes for Nissan Presage R50 depend on the year of manufacture and configuration. Below is a table with original and acceptable alternative sizes:

Year of manufacture Standard size Valid Alternatives Note
1998–2003 205/65 R15 195/70 R15, 215/60 R15 Tires 215/60 may touch the arch when fully loaded
2004–2009 215/60 R16 205/65 R16, 225/55 R16 225/55 requires checking clearances with suspension

When choosing tires, consider:

  • 📏 Diameter must match the recommended one (±3% deviation is acceptable). For example, replacement 205/65 R15 on 195/70 R15 will increase the outer diameter of the wheel by 1.5%, which is within normal limits.
  • ⚖️ Load Index - not less than 91 (615 kg per wheel) for the front axle and 94 (670 kg) for the rear (at full load).
  • 🌡️ Speed index - minimum T (up to 190 km/h) for urban use, H (up to 210 km/h) for the highway.

If you plan to install wide tires (For example, 225/55 R16), please note:

  • 🔧 It will be necessary to check the gaps with the suspension and arches at the maximum turn of the steering wheel.
  • 🚗 Fuel consumption will increase by 0.3–0.5 l/100 km due to increased rolling resistance.
  • ⚠️ There may be problems with passing the technical inspection if the dimensions are not included in the PTS.
💡

When purchasing tires for Presage, give preference to models with reinforced cords (marking Reinforced or XL). This compensates for the high load on the rear axle of the minivan.

Tuning and non-standard sizes: what is possible and what is not

Many owners Presage strive to improve the appearance of the car with large disks (17-18 inches) or low profile tires. However, this requires taking into account technical limitations:

  • 🔧 Wheels R17 — maximum permissible size without modifications. Recommended settings: 7J ET35 with tires 215/50 R17.
  • ❌ Wheels R18 — possible only with spacers (spacers 15–20 mm) and rolling arches. They require replacing the wheel bearings with reinforced ones.
  • ⚠️ Low profile tires (profile below 50) - increase the risk of damage to disks on Russian roads. Optimal balance: profile 55–60.

An example of a successful combination for tuning:

  • 🔄 Discs: 7.5J ET35 (bolt pattern) 5×114.3, DIA 66.1 mm).
  • 🔄 Tires: 225/45 R17 (load index 94, speed H).
  • 🔄 Spacers: 10 mm (if necessary).

However, even if the dimensions are respected be sure to check:

☑️ Check before installing non-standard wheels

Done: 0 / 5
⚠️ Attention: Installation of wheels with a diameter of more than R17 without appropriate changes to the PTS, it is equivalent to making changes to the design of the vehicle and requires an examination.

Common mistakes when selecting wheels for Nissan Presage

Even experienced car owners sometimes make mistakes that lead to expensive repairs. Here are the most common:

  1. Ignoring the DIA parameter. Disc with DIA 72.6 mm (for example, from Infiniti) can be installed on Presage using centering rings, but this increases the risk of wheel runout at high speeds.
  2. Incorrect departure (ET). Installing 20-30mm ET wheels without spacers places excessive stress on the wheel bearings and suspension arms.
  3. Savings on balancing. Even perfectly matched wheels require balancing every 10–15 thousand km, especially after falling into holes.
  4. Using tires with different tread patterns on one axis. This disrupts handling, especially on wet roads.

One of the most insidious mistakes is purchasing disks with incorrect mounting threads. For example, threaded nuts M12×1.5 (instead of M12×1.25) may appear to fit, but when tightened, they damage the studs, resulting in self-unscrewing of wheels while driving.

What to do if vibration appears after changing wheels?

Vibration at speeds of 80–100 km/h is most often caused by:

1. Unbalanced wheels (even new wheels require balancing!).

2. Damaged wheel bearings (check the play).

3. DIA mismatch (disc is not centered on the hub).

4. Deformed discs (after falling into a hole).

To diagnose, raise the car on a lift and spin the wheels manually - beating or noise will indicate a problem.

Where to buy wheels and tires for Nissan Presage: proven options

When purchasing wheels for Presage It is important to choose a reliable supplier to avoid counterfeits or inconsistencies in parameters. Recommended options:

  • 🛒 Official Nissan dealers - guarantee of original spare parts, but high price.
  • 🌍 Online stores:
    • KolesaDarom — a wide range of used wheels with geometry check.
    • ShinaGuide — convenient selection of tires according to vehicle parameters.
    • Exist.ru — original and analog discs with delivery.
  • 🔧 Local tire shops — there are often used wheels in good condition at low prices.

When purchasing used wheels be sure to check:

  • 🔍 Geometry (no figure eight or dents).
  • 🔧 carving mounting holes (must not be torn off).
  • 📏 Options (PCD, ET, DIA) - sellers often provide incorrect information.

Average prices for wheels for Presage (2023):

  • Steel (stamped): RUB 3,000–5,000/piece.
  • Cast (light alloy): RUB 6,000–12,000/piece.
  • Forged: RUB 15,000–25,000/piece.
💡

When purchasing tires, give preference to brands with a good reputation: Michelin, Continental, Bridgestone or Nokian. Cheap tires from unknown manufacturers may have uneven wear and poor stability on wet roads.

FAQ: Frequently asked questions about the Nissan Presage bolt pattern

Is it possible to install wheels from Nissan X-Trail on Presage?

Technically yes, since it's a bolt pattern 5×114.3 and DIA 66.1 mm are the same. However, the offset (ET) X-Trail usually 35–40 mm, and Presage — 35–45 mm. Discs with ET 35 are suitable, but more “convex” ones (ET 40+) can rub against the arches. Check clearances before purchasing.

What are the consequences if you install disks with a DIA of 72.6 mm instead of 66.1 mm?

The disc will sit on the hub, but will not be perfectly centered, which will lead to:

  • Vibrations at speeds over 80 km/h.
  • Uneven tire wear.
  • Increased load on wheel bearings.

Solution: use centering rings (adapters) with an outer diameter of 72.6 mm and an inner diameter of 66.1 mm.

What is the maximum size of disks that can be installed on Presage without modifications?

Without modifications to the suspension and arches, the maximum safe size is:

  • Drives: R17 7J ET35.
  • Tires: 215/50 R17.

For R18 you will need to roll out the arches, replace the shock absorbers with shortened ones and install spacers.

What should I do if the ABS indicator comes on after changing the wheels?

This may be caused by:

  1. Hub Diameter Mismatch (DIA) - The ABS sensor is reading incorrect data.
  2. Damage to the ABS sensor when installing the disc (check the connectors).
  3. Using magnetic caps on nuts that interfere with sensor operation.

Solution: reset the error via a diagnostic scanner (for example, ELM327) or contact service.

Can spacers be used on Presage?

Yes, but with reservations:

  • Maximum safe thickness - 10–15 mm.
  • Spacers must be hub-centered (with hole for DIA 66.1 mm).
  • It is necessary to replace the standard nuts with extended ones (at least 5–10 mm longer).

The use of spacers thicker than 20 mm requires strengthening the hub and registering changes with the traffic police.