Nissan Navara D40 bolt pattern: how to choose wheels without errors?

Nissan Navara D40 is a legendary pickup truck that has gained popularity due to its reliability and off-road capabilities. However, when replacing wheels or tires, owners often face a problem: how to choose the right bolt pattern to avoid vibrations, premature wear of wheel bearings or problems with passing inspection? In this article we will analyze all bolt pattern parameters for Navara D40 (2005–2015), including restyled versions, as well as nuances of compatibility with drives from other models Nissan and brands.

Errors when choosing disks can result not only in financial losses, but also security threat. For example, incorrect departure (ET) leads to a displacement of the steering axis, and an incorrect diameter of the central hole (DIA) - to wheel runout at high speeds. We have collected current data confirmed by the manufacturer and experienced service station technicians so that you can make an informed choice.

What is bolt pattern and why is it important for Nissan Navara D40?

Bolt pattern (or PCD — Pitch Circle Diameter) is the diameter of the circle on which the wheel mounting holes are located. For Navara D40 this parameter is critical, since the pickup truck is used in difficult conditions: towing, off-road, high loads. PCD mismatch results in:

• 🔧 Uneven tightening of bolts - the wheel “walks” when moving.
• 🚗 Vibrations on the steering wheel even when balancing.
• 💥 Risk of wheel separation on a rough road.

Unlike passenger cars, where minimal deviations are allowed, for Navara D40 required precise bolt pattern 6×139.7 mm (6 holes, circle diameter 139.7 mm). This standard is unified for many all-wheel drive pickups and SUVs, but there are nuances - more on that below.

⚠️ Attention! The use of adapter rings or bolts with an eccentric to “adjust” the bolt pattern is strictly prohibited. This violates the geometry of the fastening and can lead to an accident.

Standard wheel parameters Nissan Navara D40 (2005–2015)

The manufacturer sets strict requirements for wheels for Navara D40, which depend on the configuration and sales market. Below is a table with official data for all modifications, including diesel (2.5 dCi) and gasoline (2.5/4.0 V6) versions.

Parameter	Meaning	Note
Bolt Pattern (PCD)	6×139.7	Unified for all versions of D40
Departure (ET)	+25…+38 mm	Depends on rim width (see below)
Center Hole (DIA)	106.1 mm	Discs with DIA 106–108 mm are allowed (centering rings are used)
Disc width	7.0–8.5J	For tires 255/70 R16 and 265/65 R17
Bolt thread	M12×1.25	Bolt length - 27–30 mm

It is important to consider that departure (ET) directly affects the track width and the load on the suspension. For example, disks with ET=25 widen the track by 13 mm on each side compared to ET=38. This may be useful for off-road tuning, but it is fraught with:

• 🔄 Accelerated wear of wheel bearings (with ET < 20).
• 🚛 Touching the arches when fully loaded or with large suspension travel.
• ⚖️ Problems with passing technical inspection (in some countries deviation ET more than ±5 mm from the standard value is considered a violation).

Compatible with drives from other models Nissan and brands

Thanks to a unified bolt pattern 6×139.7, disks from Nissan Navara D40 Compatible with many pickup trucks and SUVs. However, it is necessary to check all parameters, not just PCD. Below is a list of models whose drives can be installed on Navara D40 with minimal or no modifications:

• 🚙 Nissan Pathfinder R51 (2005–2012) - full software compatibility PCD, ET And DIA.
• 🚙 Nissan Patrol Y61 (1997–2016) - bolt pattern matches, but may require adjustment ET.
• 🚙 Toyota Hilux (7th–8th generation) — PCD matches, but DIA=106.1 versus 106.0 Hilux (permissible with a centering ring).
• 🚙 Mitsubishi L200 (4th generation) — the bolt pattern is identical, but the offset may differ.
• 🚙 Isuzu D-Max — partial compatibility (check ET and rim width).

When installing drives from other models, be sure to consider:

1. Center hole diameter - even a difference of 0.5 mm can cause runout.
2. Shape of mounting holes - some disks have conical disks (60°), others have flat ones.
3. Availability of humps (protrusions for fixing a tubeless tire) - their absence is fraught with depressurization.

How to correctly measure the bolt pattern yourself?

If you are in doubt about the parameters of the disks or are buying a used set, you can measure the bolt pattern yourself. For this you will need:

• 📏 Caliper or ruler.
• 🔨 Protractor (to check the taper of holes).

PCD measurement algorithm for 6 holes:

1. Measure the distance between the centers of the two neighboring holes - get the value X.
2. Multiply X by a factor of 1.05 - this will be the diameter of the circle (PCD).
   Example: if X = 116 mm, then PCD = 116 × 1.05 ≈ 121.8 mm (but for Navara D40 there must be 139.7 mm!).

To check departure (ET):

1. Place the disc face down on a flat surface.
2. Measure the height from the surface to the mating plane (A).
3. Turn the disc over and measure the height to the trailing edge (B).
4. Departure is calculated using the formula: ET = (B – A)/2 – C, where C - half the width of the disk.

⚠️ Attention! If when measuring you get PCD = 139.5–140.0 mm, this does not mean that the disk will fit. Permissible deviation for Navara D40 - no more ±0.1 mm!

Tuning and non-standard wheels: what do you need to know?

Many owners Navara D40 looking to install wider wheels or increase offset for an aggressive appearance. However, such changes require taking into account several factors:

• 🔧 Disc width - maximum permissible for Navara D40 without modifications: 9J (tires should not be wider than 285 mm).
• 🚗 Departure (ET) - when the offset is reduced to ET=15 and below requires the installation of spacers, which prohibited by traffic rules in most countries.
• 💨 Brake ventilation — discs with a closed design can lead to overheating of the brake mechanisms.

Popular tuning options:

Goal	Recommendations	Risks
Increase track width	Discs 8.5J ET=20 + tires 265/70 R17	Increased load on wheel bearings
Raise ground clearance	Discs R18 with tires 285/65 R18 + lift kit	Poor handling at high speeds
Aggressive off-road style	Wheels with beadlocks + tires 33"	The need to trim arches and replace shock absorbers

For off-road tuning, wheels from Toyota Land Cruiser 200 or Nissan Patrol, but in this case it is required:

• 🔨 Replacing hub nuts (y Patrol carving M14×1.5 instead of M12×1.25).
• 📏 Adjustment ET using spacers (illegal in most countries).

What happens if you install disks with PCD 6x135?

Such a bolt pattern (for example, from Jeep Wrangler) is visually similar to 6x139.7, but the difference of 4.7 mm will result in only 2-3 bolts out of 6 being tightened correctly. This will cause wheel runout And uneven tire wear.

Top 5 mistakes when choosing disks for Nissan Navara D40

Even experienced car owners sometimes make mistakes that result in expensive repairs. Here are the most common:

1. Ignoring a parameter DIA - central hole diameter 106.1 mm critical for wheel alignment. Discs with DIA=110 mm (for example, from Ford Ranger) will not fit without adapters.
2. Buying wheels with incorrect bolt taper - y Navara D40 cone is used 60°. Discs with flat holes will cause the bolts to unscrew themselves.
3. Installing oversized tires without adjusting the speedometer - for example, transition from 265/70 R16 on 285/65 R18 increases the actual speed by 5–7% with the same speedometer readings.
4. Using bolts of the wrong length — bolts that are too short will not provide reliable fastening, and bolts that are too long will rest against the brake disc.
5. Buying discs without humps - this is fraught depressurization of tubeless tires during sudden maneuvers.

To avoid these mistakes, always check your settings with manufacturer data or use online compatibility calculators (for example, Wheel-Size.com).

Where to buy disks for Nissan Navara D40 and what to pay attention to?

When selecting disks for Navara D40 it is important to consider not only the parameters, but also quality of material, especially if you operate your pickup truck in difficult conditions. Recommended options:

• 🏆 Original wheels Nissan - reliable, but expensive (from 15,000 rubles per piece).
• 💎 Alloy wheels brands BBS, OZ Racing, Enkei - lightweight, durable, but require careful handling of pits.
• 🛡️ Forged wheels Forgiato, HRE — optimal for off-road use, but the price starts from 30,000 rubles. per disc.
• 🔄 Used wheels from disassembly - a cheap option, but check for cracks and corrosion.

When purchasing, pay attention to:

• 📄 Certificate of Conformity - discs without it may be counterfeit.
• 🔍 Marking - must contain PCD 6×139.7, ET, DIA and maximum load.
• 🛒 Guarantee — reliable sellers provide a guarantee of at least 1 year.

Popular platforms for purchasing:

• 🌍 Foreign sites: Amazon, eBay (but please consider shipping costs and possible duties).
• 🏢 Russian stores: Kolesa-Darom.ru, Rezulteo.ru, BlackTyres.ru.
• 🔧 Local service stations — they often offer wheels tailored for a specific car.

FAQ: Frequently asked questions about bolt pattern Nissan Navara D40

Is it possible to install disks from Nissan Patrol Y61 on Navara D40 without modifications?

Yes, but only if they match all parameters: PCD 6×139.7, ET And DIA. U Patrol Y61 often used ET=30–35, which is close to standard for Navara D40 (ET=25–38). However, check bolt thread - y Patrol maybe M14×1.5 instead of M12×1.25.

Which tires are best for rims? R17 ET=30?

The optimal choice is tire size 265/65 R17 or 265/70 R17. Suitable for off-road use:

• 🏜️ BFGoodrich All-Terrain T/A KO2 - universal for asphalt and dirt.
• 🌲 Yokohama Geolandar M/T G003 — aggressive tread for serious off-road use.
• 🛣️ Michelin LTX Force - for predominantly asphalt use.

Avoid wider tires 285 mm without a lift kit - they will touch the arches when fully loaded.

What should I do if, after replacing the disks, vibration appears at speeds of 80–100 km/h?

The causes of vibration may be the following:

1. Incorrect balancing - even a new disk requires balancing with the tire.
2. Mismatch DIA - if the central hole is larger than 106.1 mm and there is no centering ring.
3. Warped disc — check at the stand.
4. Incorrect bolt torque - for Navara D40 he makes up 100–120 Nm.

Check first bolt tightening And balancing. If the problem persists, contact a service station to diagnose the suspension.

Is it possible to use wheel spacers on Navara D40?

Technically yes, but:

• ⚖️ In most countries this is violates traffic rules (change in vehicle design).
• 🔧 Spacers increase the load on wheel bearings and steering rods.
• 📏 Permissible thickness of spacers - no more 10 mm (with ET disk not lower 20).

It is better to choose wheels with the desired offset than to risk safety.

What bolts are needed for Navara D40?

Standard bolts have the following parameters:

• 🔩 Carving: M12×1.25.
• 📏 Length: 27–30 mm (depending on the thickness of the disc).
• 🔧 Cone: 60°.

When using wheels with a thicker mating surface (for example, forged ones), bolts of length 35–40 mm.