Nissan Qashqai 2019 bolt pattern: complete guide to wheel and rim parameters

Selection of rims for Nissan Qashqai 2019 - a task that requires attention to detail. An error in the bolt pattern parameters can lead not only to vibrations during movement, but also to serious damage to the suspension. This second generation crossover (body J11) has strict requirements for wheel geometry, which depend on the modification and engine.

In this article we will look at all key parameters: from standard PCD 5×114.3 to permissible overhang values (ET) and the diameter of the central hole (DIA). You will learn what sizes of wheels and tires the manufacturer recommends, as well as how to avoid common mistakes when choosing. We will pay special attention to the differences between versions with gasoline and diesel engines - they affect the load on the suspension and, as a result, the choice of wheels.

What is a bolt pattern and why is it important for the 2019 Qashqai

Bolt pattern (or PCD - Pitch Circle Diameter) is the diameter of the circle on which the wheel rim mounting holes are located. For Nissan Qashqai 2019 this parameter is fixed: 5×114.3. This means that the disc has 5 holes located on a circle with a diameter of 114.3 mm.

Why is this critical? A mismatched bolt pattern leads to:

• 🔧 Uneven disc fit to the hub - even if the bolts are screwed in, the wheel will “beat” at speed.
• 🚗 Accelerated wear wheel bearings and suspension elements.
• ⚠️ Unscrewing the wheel while driving (in extreme cases).

On Qashqai J11 it is also important to consider ET (disc ejection) and DIA (diameter of the central hole). The manufacturer sets strict tolerances for these parameters, especially for versions with all-wheel drive (4WD).

Official bolt pattern parameters for all modifications

Nissan strictly regulates wheel parameters for Qashqai 2019. Below is a table with data for all versions, including petrol (1.3 DIG-T, 1.6, 2.0) and diesel (1.5 dCi, 1.6 dCi) engines:

Parameter	Meaning	Note
Bolt pattern (PCD)	5×114.3	Single standard for all modifications
Departure (ET)	38–45 mm	For versions with 4WD recommended ET 40–45
Central hole diameter (DIA)	66.1 mm	Discs with DIA 67.1 mm (with adapter rings)
Mounting bolt thread	M12×1.25	Bolt length - 27–30 mm
Tightening torque	100–120 Nm	Over-tightening leads to hub deformation

Important: For versions with the system All-Mode 4×4-i (all-wheel drive) disc offset must be at least ET 40. Using discs with ET 35 or lower will lead to increased load on the wheel bearings and premature wear of the suspension elements.

⚠️ Attention: Discs with DIA 71.6 mm (for example, from Toyota RAV4) can be physically installed on Qashqai using centering rings, but this unbalances the wheel and increases the risk of vibration at speeds above 120 km/h.

Recommended wheel and tire sizes for Qashqai 2019

The manufacturer offers several options for wheel sizes depending on the configuration. Basic versions (Visia, Acenta) are equipped with disks R17, while the top ones (Tekna, N-Connecta) — R19. The following are valid combinations:

• 🔄 17 inches: 215/65 R17 or 225/60 R17 — optimal balance of comfort and controllability.
• 🔄 18 inches: 225/55 R18 - standard for most trim levels.
• 🔄 19 inches: 225/50 R19 or 235/45 R19 — improved handling, but suspension stiffness increases.
• ⚠️ 20 inches: 235/40 R20 — not recommended for everyday use (risk of damage to discs on uneven surfaces).

When choosing custom sizes, consider:

• 📏 Disc width must match the width of the tire. For example, for 225/55 R18 optimal disk width - 7.5J.
• ⚖️ Load Index tires must be at least 91T (for petrol versions) and 94H (for diesel engines).
• ❄️ Winter tires It is allowed to install on 1 size already summer (for example, 215/60 R17 instead of 225/55 R17).

How to measure the bolt pattern on a Qashqai yourself

If you buy used wheels or are in doubt about the markings, you can measure the bolt pattern yourself. You will need a caliper or ruler. Follow the instructions:

1. Remove the wheel and clean the hub from dirt.
2. Measure the distance between the centers of two adjacent holes (for example, A).
3. Multiply the resulting value by the coefficient 1.701 (for 5 holes). The result should be close to 114.3 mm.

Formula for calculation:

PCD = расстояние между соседними отверстиями × 1.701

To check departure (ET):

1. Place the disc face down on a flat surface.
2. Measure the distance from the plane of contact to the hub to the edge of the rim (B).
3. Turn the disk over and measure the distance to the opposite edge (B).
4. Departure is calculated using the formula: ET = (B + V)/2 – V.

⚠️ Attention: The measurement error should not exceed ±1 mm. For accuracy, use a digital caliper. Measurement error ET by 5 mm can lead to the wheel hitting the arch when the steering wheel is turned completely.

What to do if the bolt pattern does not match?

If you purchased 5x112 or 5x108 PCD drives, they can only be installed using adapters. However, this compromises the suspension geometry and voids the wheel bearing warranty. We recommend selling such discs and choosing the right ones.

Typical mistakes when selecting disks and how to avoid them

Even experienced car owners sometimes make mistakes. Here are the most common:

• 🔧 Ignoring crash (ET). Discs with ET 30 visually look aggressive, but overload the wheel bearings. For Qashqai 2019 minimum permissible departure - ET 38.
• 🌀 Mismatch DIA. Discs with central hole 71.6 mm (for example, from Volkswagen) require centering rings, but even with them the balancing deteriorates.
• ⚡ Incorrect tightening torque. Overtightened bolts deform the hub, while undertightened bolts cause the wheel to unscrew. Use a torque wrench!
• ❄️ Summer tires in winter (and vice versa). Rubber with an inappropriate temperature index loses grip when +7°C and below.

To avoid problems:

• 📋 Buy discs only with markings Nissan Qashqai J11 or universal with parameters 5×114.3 ET38-45 DIA66.1.
• 🔍 Check the discs for runout before installation (the permissible value is no more than 0.5 mm).
• 🛠️ Install wheels in certified tire shops with computer balancing.

Impact of non-standard drives on manageability and safety

Installing disks with settings other than the recommended ones affects:

1. Controllability: Discs with ET 30 widen the track, which improves stability on straight lines, but worsens maneuverability. On Qashqai This manifests itself as a "stiff" steering wheel in a parking lot.
2. Suspension wear: Increased reach (ET 50+) shifts the center of gravity of the wheel inward, accelerating the wear of shock absorbers and silent blocks.
3. Braking dynamics: Discs R20 with low profile tires (235/40) reduce ground clearance and may interfere with brake calipers.

Manufacturer Nissan Conducted crash tests with different wheel configurations. The results showed that the deviation from standard parameters is more than ±5 mm by ET increases the risk:

• 🚨 Loss of control on a wet road (due to changes in the tire contact patch).
• 🔥 Overheating of brake discs (cooling worsens due to improper air exchange).
• 💥 Premature wear of the steering rack (20–30% faster with ET < 35).

Where to buy wheels for Qashqai 2019: proven options

When choosing a place of purchase, focus on:

• 🏆 Official dealers Nissan: Guaranteed compatibility, but high price (from 12,000 RUR per disk R18).
• 🛒 Specialty stores (K&K, Replica, NZ): High-quality analogues at a price 30% lower than the original.
• 🌍 Foreign sites (Amazon, eBay, Aliexpress): There is a risk of running into a fake, but there are options with free shipping.
• 🔄 Used market (Avito, Drom): Cheap, but requires careful testing (see section on errors).

When purchasing online, pay attention to:

• 📄 Availability of a certificate of conformity (for Russia - TR TS 018/2011).
• 📦 Packaging: Original discs Nissan supplied in branded boxes with a hologram.
• 💬 Reviews: Look for mentions of a specific model Qashqai J11 (for example, “installed on Tekna 1.6 dCi - no problem”).

Average prices for new wheels (2026):

• 🔄 R17 (stamped): 5,000–8,000 ₽.
• 🔧 R18 (cast): 9,000–15,000 ₽.
• ⚡ R19 (forged): 18,000–25,000 ₽.

⚠️ Attention: When purchasing discs on AliExpress check the country of origin. Discs from China often have low strength (marking JWL instead of JWL-T), which is dangerous when driving off-road.

FAQ: Frequently asked questions about the Nissan Qashqai 2019 bolt pattern

Is it possible to install wheels from Nissan X-Trail T32 on Qashqai 2019?

Yes, but with reservations. X-Trail T32 has the same bolt pattern 5×114.3, but the disc offset may differ (ET 40–48). Before purchasing please check:

• Coincidence DIA (must be 66.1 mm).
• Disc width (for Qashqai optimal 7.0–8.0J).

Discs from X-Trail with ET 48 visually “sink” the wheel inside the arch, which worsens handling.

What are the consequences if you install disks with PCD 5x112?

Technically, such disks can only be installed using adapters (for example, from H&R), but this will result in:

• 🔧 Increased load on wheel bearings (lifetime is reduced by 40–50%).
• 🚗 Uneven tire wear (due to a shift in the center of gravity of the wheel).
• ⚠️ Risk of the adapter unscrewing when driving off-road.

Manufacturer Nissan officially prohibits the use of adapters in the manual (section 9.7).

What is the maximum size of wheels that can be installed on the Qashqai 2019 without modifications?

Without suspension and arch modifications, maximum dimensions:

• 🔄 R19 with tires 235/45 - for versions with gasoline engines.
• 🔧 R18 with tires 225/55 - for diesel versions (due to greater weight).

Discs R20 will require:

• Spacer installations (minimum thickness - 15 mm).
• Trims of plastic fender liners.
• Replacing shock absorbers with shortened ones (for example, Bilstein B4).

Do I need to balance my wheels after a seasonal tire change?

Yes, even if the wheels were not removed from the car. Reasons:

• 🌀 Uneven tire wear over the season (especially on Qashqai with all-wheel drive).
• 🔧 Possible deformation of the disc from pits (checked at the stand).
• ⚖️ Change in weight distribution due to residual dirt or ice in the tread.

The cost of balancing at a tire shop is from RUB 500 per wheel. Savings on this procedure lead to:

• Steering wheel vibrations at speed 90–110 km/h.
• Accelerated wear of the hub bearings.

What bolts are needed for wheels on Qashqai 2019?

Official parameters of mounting bolts:

• 🔩 Carving: M12×1.25.
• 📏 Length: 27–30 mm (for alloy wheels it is better to take 30 mm).
• 🔧 Tightening torque: 100–120 Nm.

For versions with all-wheel drive (4WD) bolts with cone fit (original article number - 40520-95F0A). Using bolts with a flat washer results in disc play.