Fog lights for Nissan Teana J31: a complete guide to selection, installation and configuration

Nissan Teana J31 - a car that is valued for its comfort, reliability and stylish design. However, even in the basic configurations of this sedan there are often no fog lights (FTL), which creates problems when driving in poor visibility conditions. In this article we will look at how to correctly select, install and configure PTF on Teana J31so that they not only fulfill their function, but also fit harmoniously into the exterior.

Fog lights are not just a tuning element, but also an important safety component. They improve visibility in fog, rain or snow by illuminating the road at an angle that minimizes light reflection from water droplets. However, incorrect selection or installation can result in blinding oncoming drivers or even a fine. Therefore, you need to approach this issue responsibly.

Original fog lights for Nissan Teana J31: part numbers and features

If you prefer original spare parts, then for Teana J31 (2008–2013) suitable PTF from Nissan with articles:

• 🔦 26510-4M000 (right headlight)
• 🔦 26511-4M000 (left headlight)
• 🔦 26510-4M001 (updated version for restyling)

Original headlights come with bulbs H11 (power 55 W) and have clear light and shade that meets European standards. Their advantages:

• ✅ Perfect fit without bumper modifications
• ✅ Compliance with standard ECE R19 (approved for use in Russia)
• ✅ Durability and protection from moisture (class IP67)

However, the price of the original can reach 8–12 thousand rubles per pair, which is not always justified. In addition, in some trim levels Teana J31 (For example, 2.5L Luxury) seats for PTF are already provided, but the headlights themselves are missing - they can be purchased separately.

⚠️ Attention: When purchasing original headlights, check compatibility with your year of manufacture. Models before and after 2011 may have different connection connectors.

Analogs of original PTFs: which brands are worth considering?

If original headlights are too expensive, you can pay attention to high-quality analogues. The main thing is to choose certified models that meet the standard ECE R19. Top Brands:

Brand	Model/Article	Price (per pair), ₽	Features
Depo	26510-4M000-DP	4 500–5 500	Good build quality, design close to the original
TYC	20-6510-00-1	5 000–6 000	Improved light transmittance, vibration resistant
Hella	8GA 008 141-121	7 000–8 500	Premium quality, long service life
Bosch	1 987 302 015	6 500–7 500	Improved focusing optics, suitable for difficult weather conditions

When choosing analogues, pay attention to:

• 💡 Lamp type - should be H11 (as in original)
• 🔧 Fastening — check compatibility with the bumper Teana J31
• 📜 Certification — presence of markings E19 or E1 on glass

⚠️ Attention: Cheap, uncertified PTFs (for example, unnamed Chinese models) can blind oncoming drivers and cause accidents. Their use is prohibited by traffic regulations (clause 3.6 "List of faults").

📊 Which fog lights do you prefer?

• Original Nissan
• High-quality analogues (Hella, Bosch)
• Budget analogues (Depo, TYC)
• I haven't decided yet

Wiring diagram for fog lights on Nissan Teana J31

If your car is not equipped with PTF from the factory, you will have to install the wiring yourself. B Teana J31 There is a standard button for turning on the fog lights (next to the light switch), but relays and fuses are often missing. To connect you will need:

• 🔌 Relay (4-pin, 30/40 A)
• 🔌 fuse (15–20 A)
• 🔌 Wires (section 1.5–2.0 mm²)
• 🔌 Terminals ("mom"/"dad")

Standard connection diagram:

1. From battery (+12V) the wire goes through the fuse to the contact 30 relay
2. Contact 85 the relay is connected to the PTF power button (usually orange-black wire in the light control unit).
3. Contact 87 relay connects to +12V on the headlights.
4. Weight taken from the body next to the headlights.

To simplify the task, you can use a ready-made wiring kit for PTF (for example, from Hella or Bosch), where all the wires are already marked.

Disconnect the battery before work|Crimp the wires for protection|Insulate all connections with heat shrink|Check polarity before turning on-->

Installing fog lights: step-by-step instructions

The process of installing PTF on Nissan Teana J31 includes several stages: dismantling the bumper, attaching the headlights and connecting the wiring. Let's look at each step in detail.

1. Removing the bumper

To access the seats, you must remove the front bumper. Algorithm:

1. Unscrew 4 bolts mounting the bumper from below (under the radiator grille).
2. Disconnect 2 pistons on the sides (next to the wheel arches).
3. Carefully pull the bumper towards you, snapping the clips along the top edge.

2. Headlight mounting

In the bumper Teana J31 There are special holes for PTF. If they are not there (on some versions), you will have to cut out the seats according to the template. Next:

• 🔨 Attach the headlights to standard bolts or screws (included).
• 🔧 Connect the connectors to the lamps (the polarity is indicated in the instructions).
• 🛠️ Place the bumper in place, securing all fasteners.

3. Connection and testing

After installation:

• 🔋 Connect the battery.
• 💡 Turn on the PTF with the button on the panel - they should light up without flickering.
• 🔍 Check the angle of inclination: the light beam should illuminate the road and not blind oncoming drivers.

Adjusting fog lights: how to avoid a fine?

Incorrectly adjusted PTFs are one of the main reasons for the blinding of oncoming drivers and fines from the traffic police (under Article 12.5 of the Administrative Code, fine 500 rubles). To avoid problems, follow the instructions:

1. Preparation

To adjust you will need:

• 📏 Flat area (no slope)
• 📐 Vertical wall or screen in the distance 5–10 meters from the car
• 🔧 Screwdriver for adjusting screws

2. Screen layout

Draw the following lines on the wall:

• 🔹 Horizontal line at the height of the PTF centers from the ground (usually 40–50 cm).
• 🔹 Vertical lines in the center of each headlight.

3. Setup

Turn on the PTFs and adjust them so that:

• 🎯 The upper border of the light spot coincided with the horizontal line.
• 🎯 The right edge of the spot did not go beyond the vertical line (for the left headlight - vice versa).

Adjustment is carried out by rotating the screws on the headlight housing (usually they are located on the top and side).

What happens if you drive with incorrectly adjusted PTFs?

In addition to a fine, such headlights create a danger on the road: blinding oncoming drivers can lead to an accident. In addition, an incorrect angle of inclination reduces the effectiveness of road lighting, which impairs visibility in fog.

Common installation mistakes and how to avoid them

Even experienced car owners make mistakes when installing PTF. Let's look at the most common ones and ways to prevent them.

1. Incorrect polarization

If you confuse + And – When connected, the lamps may burn out or operate unstably. Always check the diagram before connecting!

2. Poor wire insulation

Poor quality insulation leads to short circuits or oxidation of contacts. Use heat shrink tubing instead of electrical tape.

3. Ignoring adjustment

Many people install PTFs and do not regulate them, which leads to blinding other road users. Adjustment is required!

4. Use of uncertified lamps

High wattage lamps (e.g. 100 W instead of 55 W) overload the wiring and can melt the plastic of the headlight.

Tuning and modernization of fog lights

If standard PTFs do not suit you, you can consider tuning options. The main thing is not to break the law and not to worsen security.

1. Replacing lamps with LEDs

LED lamps (for example, Philips X-tremeUltinon or Osram LEDriving) give brighter and whiter light, but have nuances:

• ⚡ Required Canbus compatible drivers (otherwise there will be an error on the panel).
• ⚡ Must have a certificate ECE R19.
• ⚡ Can only be installed in lensed headlights (they are blinding in reflector headlights).

2. Installation of additional protective grilles

Metal or plastic grilles (for example, from Rally Armor) protect headlight glasses from chipping, but can impair light transmittance. Choose models with a small cell.

3. Painting the headlight housing

Black or chrome PTF cases look stylish, but it is important to use heat resistant paintso as not to damage the plastic.

⚠️ Attention: Installing xenon in PTF is prohibited by law (Article 12.5 of the Administrative Code, fine 3,000 rubles with confiscation of lamps). Xenon lamps require mandatory installation headlight washer And autocorrectorwhat's on Teana J31 not provided.

FAQ: answers to frequently asked questions

Is it possible to install PTF on a Nissan Teana J31 without removing the bumper?

Theoretically it is possible, but it is extremely inconvenient. The mounting spots for the headlights are deep, and without removing the bumper you will not be able to securely mount them and connect the wiring. We still recommend removing the bumper - it will take no more than 30 minutes.

Which lamps are better to choose for PTF: halogen, LED or xenon?

The best option is halogen lamps (For example, Osram Night Breaker or Philips RacingVision). They are certified, do not require modifications and provide good light. LED lamps can only be installed in lensed headlights, and xenon is prohibited without a washer and corrector.

Where is the PTF fuse located in Nissan Teana J31?

Fog light fuse (usually 15 A) is located in the mounting block under the steering wheel. It can be designated as F30 or Fog Lamp. The exact location is indicated in the car manual.

Is it possible to connect PTF to dimensions?

No, this is prohibited by the traffic rules (clause 19.4). Fog lights must be turned on only with a separate button and operate independently of the side lights. Connecting to dimensions may result in circuit overload and fire.

How often do lamps in PTFs need to be changed?

The service life of halogen lamps is approx. 500–1000 hours. If you often drive in fog, have them checked once a year. Signs of replacement: dim light, flickering or burnout of one of the lamps.