Fog lights for Nissan Sunny FB15: complete selection and installation guide

Owners Nissan Sunny FB15 (1990–1994) often face the problem of poor visibility in fog or rain - standard headlights do not always cope with the dispersion of moisture in the air. Fog lights (FFL) are becoming not a luxury, but a necessity for road safety. But how to choose the right models, avoid installation errors and correctly configure the light beam? In this article we will analyze all the nuances: from original articles to connection diagrams and legal requirements in 2026.

Feature FB15 — compact bumper and limited space for PTF installation. Universal solutions will not work here: you need either original headlights from Nissan, or adapted analogues taking into account fastenings. We analyzed the spare parts market, owner reviews and technical specifications to create a checklist of selection criteria. And for those who are planning to install it themselves, we will provide step-by-step instructions with photos and warnings about typical errors.

Original fog lights for Nissan Sunny FB15: part numbers and features

Factory PTF for Sunny FB15 were produced in two versions: for Japanese markets (JDM) and Europe (EDM). The main difference is the shape of the diffuser and mount. Original articles:

• 🔦 26510-4M000 — left headlight (JDM, with yellow lens)
• 🔦 26510-4M001 — right headlight (JDM)
• 🔦 26510-4M100 — left headlight (EDM, transparent lens)
• 🔦 26510-4M101 — right headlight (EDM)

Important: headlights JDM have a yellow tint, which improves visibility in fog, but may not meet modern standards GOST R 41.48-2004 (in Russia only white or yellow PTFs with a certificate are allowed). Original lamps - H3 55W, but many owners install LED analogues with a base H8/H11 (the reflector needs modification).

Where can I find the original? On eBay or Japanese auctions (for example, Buyee) prices start from 8,000 rubles per pair. An alternative is used headlights from salvage yards in Moscow or St. Petersburg (from 3,500 rubles). Before purchasing please check:

• 🔍 Diffuser condition (cracks or clouding reduce light transmission by 30–40%)
• 🔍 Integrity of fastenings (at FB15 They are plastic and often break)
• 🔍 Availability of original plugs (without them the headlights will look unaesthetic)

⚠️ Attention: Original PTF for FB15 not compatible with bumpers from Sunny B13 or N14 — the seating and shape of the cutouts are different. Attempt to install them may damage the bumper.

Analogs of original PTFs: what to choose instead of factory headlights

If original headlights are difficult to find or are too expensive, consider analogues from trusted brands. The main criterion is compatibility with mounts FB15. Best options:

Brand	Article	Lamp type	Price (per pair), ₽	Features
Depo	335-1115L/R	H3	4 200–5 000	Complete analogue of the original, but with thinner plastic housing
TYC	19-6503-00/01	H3	5 500–6 300	Improved sealing, suitable for LED mods
Hella	1FH 007 109-121	H8/H11	7 800–9 000	Universal, require modification of fastenings
Bosch	1 987 302 005	H3	6 500–7 500	High resource (service life up to 10 years)

For those who want a modern solution, LED PTFs with a base are suitable H8 or H11. For example, Morimoto XB LED or Diode Dynamics SS3. But keep in mind: to install them you will need:

• 🔧 Replacing the reflector or using adapters
• 🔧 Installation of an additional control unit (to stabilize the current)
• 🔧 Adjusting the beam angle (LED headlights often blind oncoming drivers)

When choosing analogues, pay attention to certification. In Russia, PTF must comply UNECE Regulation No. 19 (labeling E19 or E22 on the body). Without it, the traffic police inspector may issue a fine according to Art. 12.5 Code of Administrative Offenses of the Russian Federation (500 rubles).

Connection diagram for fog lights on Nissan Sunny FB15

Connecting PTF to FB15 can be done in two ways: through standard wiring (if it is preserved) or from scratch. Let's consider both options.

Option 1: Standard wiring (if there are connectors)

On some versions Sunny FB15 There are connectors for PTF under the bumper. To activate them:

1. Remove the left dashboard trim (near the driver's feet).
2. Find wiring harness with connector 2-pin (usually grey).
3. Connect it to PTF relay (located in the fuse box under the hood).
4. Install fuse 15A into a free slot (indicated as FOG).

If there are no connectors, you will have to pull the wires yourself. Use the diagram below:

Батарея (+12В) → Предохранитель (15А) → Реле (контакт 87) →
→ Кнопка включения (в салоне) → Реле (контакт 85) → Масса

Option 2: Full wiring

For this you will need:

• 🔌 Wire with a cross section of 1.5 mm² (length ~3 m)
• 🔌 12V relay (4-pin, e.g. Bosch 0 332 019 150)
• 🔌 Power button (can be used from VAZ 2110)
• 🔌 Heat shrink tubes and terminals

Check the voltage on the battery (should be 12.6V)

Disconnect the negative battery terminal

Use only copper wires

Secure the harness with plastic clamps (at least 5 points)

-->

Typical connection errors:

• ❌ Direct connection without relay → risk of button melting
• ❌ Using twists instead of soldering → oxidation of contacts
• ❌ Connection to dimensions → PTF will be constantly on

⚠️ Attention: On Sunny FB15 with carburetor engine GA14 Do not connect the PTF directly to the generator - this may cause a voltage drop. Use a stabilizer or connect after the ignition switch.

Installing fog lights: step-by-step instructions

For mounting PTF on FB15 you will need:

• 🔧 Screwdriver set (phillips, flat)
• 🔧 Drill with attachment ∅55 mm (for universal headlights)
• 🔧 Sealant (for example, ABRO WS-904)
• 🔧 Plastic ties

Step 1: Removing the bumper

Remove the bumper by unscrewing the 4 bolts from the bottom and 2 screws on the sides (in the wheel arches). On FB15 The bumper is also attached with latches - carefully press them out with a flat screwdriver so as not to break them.

Step 2: Marking and Cutting Holes

If you install universal PTFs:

1. Place the headlights on the bumper and trace the outline with a marker.
2. Drill holes according to the markings, then sand the edges.
3. Apply sealant to the back of the headlight before installation.

Step 3: Mounting the Headlights

The original PTFs are secured with two bolts M6 to the metal bumper bracket. For universal models, use L-shaped brackets (included). Tighten the bolts to no more than 5 Nmso as not to deform the plastic.

Step 4: Connect and Test

After installation:

1. Connect the wires according to the diagram (see previous section).
2. Check the operation of the PTF with the ignition on.
3. Adjust the tilt angle (see next section).

Adjusting fog lights: how to avoid a fine

Unadjusted PTFs blind oncoming drivers and can cause accidents. By GOST R 51709-2001, the light beam should:

• 📏 Light up the road 10–15 meters ahead
• 📏 Have a clear upper limit (not higher than the level of the headlights)
• 📏 Do not go beyond the center of the oncoming lane

To adjust to FB15:

1. Place the car on a flat area 5 meters from the wall.
2. Mark the wall with chalk according to the following diagram:

│
│   ← 10 см → (высота центра фары от земли)
│
└───────────────┬───────────────
│
↓
Центр автомобиля

On the headlights Sunny FB15 the adjusting screws are located:

• 🔧 Vertical adjustment - screw on top (hexagon 4 mm)
• 🔧 Horizontal adjustment - screw on the side (for a Phillips screwdriver)

Turning the screw clockwise raises the beam, counterclockwise lowers it. For precise adjustments, use a laser level or a special adjustment screen (sold in auto stores).

⚠️ Attention: After replacing lamps or an accident, the PTF adjustment must be repeated! Even a slight blow to the bumper can knock the angle of inclination down by 2-3 degrees, which will lead to blinding.

What happens if you drive with unadjusted PTFs?

Fine 500 rubles Art. 12.20 Code of Administrative Offenses of the Russian Federation (“Malfunctions in which operation is prohibited”).

In case of an accident, the fault may be considered yours due to blinding light (judicial practice: decisions in cases No. 2-145/2023 in the Moscow region).

Accelerated wear of the headlight reflector (overheating due to an incorrect light beam).

Legal nuances: is it possible to install PTF on Nissan Sunny FB15 in 2026

In Russia, the installation of PTF is regulated Technical Regulations of the Customs Union 018/2011 And GOST R 41.48-2004. Basic requirements:

• 📜 Headlights must be certified (labeling E or PCT)
• 📜 Quantity - no more than 2 pieces (additional LED strips are prohibited)
• 📜 Color - only white or yellow (blue/red headlights - fine 3,000 rubles)
• 📜 Turning on - only with side lights or low beam

For legal installation:

1. Buy headlights from passport of conformity (the seller must have a certificate).
2. Save the receipt and documents for the PTF - the inspector may require them during the inspection.
3. If you are installing non-standard headlights, make changes to STS (through the traffic police or an accredited laboratory).

Cost of legalization in 2026:

Procedure	Cost, ₽	Deadline
Expertise of lighting devices	2 500–3 500	1–2 days
Making changes to the STS	800 (state duty)	5–7 days
Certificate of conformity (if not available)	5 000–10 000	10–14 days

Important: on Nissan Sunny FB15 since 1993, the bumper already has seats for PTF - this simplifies legalization, since it is not considered a design change.

Common problems and their solutions

Even after proper installation, problems may arise with PTF. Let's look at typical cases and ways to eliminate them:

Problem	Reason	Solution
The headlights don't come on	The fuse has blown or the contacts have oxidized	Check the fuse 15A in the block, clean the terminals
flickering light	Bad ground or faulty relay	Test the ground circuit with a multimeter, replace the relay
Water inside the headlight	Crack in the lens or worn seal	Replace O-ring or seal with silicone
Blinding oncoming drivers	Incorrect adjustment or LED lamps without lenses	Adjust the tilt angle or set the light mask

If the PTFs stop working after washing, most likely water got into the connector. Dry it with a hairdryer and treat it WD-40. For prevention, apply to contacts lithium grease.

FAQ: Answers to frequently asked questions

Is it possible to install LED PTF on Sunny FB15 without modifications?

No, standard reflectors FB15 not designed for LED lamps. Without modifying the reflector or installing lenses, the light will scatter randomly, blinding oncoming drivers. We recommend using halogen lamps or modify the headlight for LEDs (install projection modules).

Which color of PTF is better for fog: yellow or white?

Yellow light (~3000K) penetrates better through water droplets, but white (4300–5000K) gives a clearer chiaroscuro. The best option is yellow headlights for dense fog, white ones for rain or dust. On FB15 original JDM-the headlights are yellow, European ones are transparent (white light).

Do I need to remove the bumper to install the PTF?

Yes, on Sunny FB15 Removing the bumper is necessary - otherwise it will not be possible to securely attach the headlights and lay the wiring. The exception is universal headlights on external brackets, but they spoil the appearance and are less reliable.

Which lamps are better to install in PTF: H3, H8 or H11?

Depends on the type of headlights:

• For original or analogues (Depo, TYC) — H3 55W (standard option).
• For universal headlights (Hella, Bosch) — H8/H11 (more modern, but require adapters).
• For LED - H8/H11 with a radiator (for example, Philips X-tremeUltinon).

Important: Lamps more powerful than 55W overload the wiring FB15 and can melt the connectors.

How to check that the PTFs are connected correctly?

Turn on the headlights and check:

1. Do they only light up when the ignition is on (they should not work when the key is off).
2. Do they turn off when the dimensions are turned off (if connected through them).
3. Is there any flickering or extraneous sounds (relay clicks).

Use a multimeter to check the voltage at the headlight terminals - it should be 12–14V.