Nissan Almera G15 (2012–2019) is a popular sedan, but even such a reliable car occasionally has electrical problems. One of the most common is the failure of the cigarette lighter fuse. This may occur due to the connection of powerful devices (such as compressors or inverters), a short circuit or normal wear and tear. Unlike more serious breakdowns, you can replace the fuse yourself in 5–10 minutes if you know the exact circuit and ratings.

In this article you will find detailed instructions for finding and replacing the cigarette lighter fuse on Almera G15, including a photo of the fuse box, a table of ratings, and tips for diagnosing related problems. We'll also look at why a new fuse might blow again and how to avoid it. If your cigarette lighter has stopped working or your devices are not charging, start by checking this element.

Where is the cigarette lighter fuse on Nissan Almera G15

B Almera G15 The cigarette lighter fuse is located in interior fuse box, which is located to the left of the steering column, behind the plastic cover. To access it:

  1. Open the driver's door and sit in the seat.
  2. Look at the panel to the left of the steering wheel - there you will see a small plastic cover with the inscription FUSE.
  3. Pry the cover with your finger or a flathead screwdriver and remove it.

Under the cover you will find a fuse and relay box. Cigarette lighter fuse Almera G15 designated as CIGAR or PWR OUTLET (depending on the year of manufacture) and has nominal 15A (yellow). There is usually a diagram on the inside of the block cover showing the location of each fuse.

💡

If there is no diagram on the block cover, take a photo of the location of the fuses before removing them - this will help avoid confusion when reinstalling.

Cigarette lighter fuse ratings and diagrams

B Nissan Almera G15 The cigarette lighter fuse has a standard rating 15 Amps, but in some configurations (for example, with additional 12V sockets) other values may be used. Below is a table with exact data for different years of manufacture:

Year of manufacture Fuse designation Denomination (A) Color Additional 12V sockets
2012–2014 CIGAR 15 Yellow No (cigarette lighter only)
2015–2017 PWR OUTLET 20 Yellow (sometimes orange) Yes (socket in trunk)
2018–2019 ACC SOCKET 15 Yellow Yes (socket in the trunk and back row)

If in your Almera G15 An additional 12V socket is installed (for example, in the trunk), it can be connected to a separate fuse with a rating 20A. You can check this using the diagram on the block cover or in instruction manual (section Fuses and Relays).

How to check the fuse rating without a diagram?

If there is no diagram, remove the fuse and look at its body - the rating is indicated in amperes (for example, 15A). You can also be guided by color: 15A - yellow, 20A - yellow or orange, 25A - white.

Step-by-step instructions for replacing the fuse

Replacing the cigarette lighter fuse with Nissan Almera G15 takes no more than 5 minutes. You will need:

  • 🔧 Flat screwdriver (for removing the block cover).
  • 🔋 New fuse with a rating of 15A or 20A (depending on the configuration).
  • 📱 Flashlight (optional, for better lighting).

Sequence of actions:

  1. Turn off the ignition and make sure all electrical appliances are turned off.
  2. Remove the fuse box cover (as described above).
  3. Find the fuse CIGAR/PWR OUTLET according to the diagram or visually (usually this is the 5th–7th position in the top row).
  4. Use special tweezers (included in the unit) or pliers to remove the old fuse.
  5. Check it for integrity: if the wire element inside is burned out, the fuse must be replaced.
  6. Install a new fuse same denomination.
  7. Close the unit cover and check the operation of the cigarette lighter.

Ignition and all instruments are turned off|New fuse matches the rating|Tools at hand|Fuse box diagram studied-->

Important: Never install a fuse with a rating higher than specified (for example, 20A instead of 15A). This may result in melted wiring or fire!

Why does the cigarette lighter fuse blow repeatedly?

If a new fuse blows immediately after installation, this indicates short circuit or circuit overload. Main reasons:

  • ⚡ Faulty deviceconnected to the cigarette lighter (for example, a compressor with damaged insulation).
  • 🔌 Oxidation of contacts in the cigarette lighter socket or fuse box.
  • 🔥 Wiring damage (for example, after unqualified installation of an alarm system).
  • 🔋 Using splitters with several powerful devices (for example, DVR + radar detector + laptop charger).

To diagnose the problem:

  1. Disconnect all devices from the cigarette lighter.
  2. Install a new fuse and turn on the ignition. If it does not burn out, the problem is in one of the devices.
  3. Connect the gadgets one by one to identify the culprit.
  4. If the fuse burns even without load, check the wiring with a multimeter or contact service.

Phone Charger|Dash Cam|Tire Compressor|Radar Detector|Other Gadget-->

⚠️ Attention: If, when replacing a fuse, you smell a burning smell or notice melted contacts in the block, do not use the cigarette lighter until the cause is eliminated! This may cause a fire.

How to check the cigarette lighter and 12V socket with a multimeter

If the fuse is intact but the cigarette lighter does not work, the problem may be 12V socket or wiring. For diagnostics you will need a multimeter:

  1. Set the multimeter to DC voltage measurement mode (DC 20V).
  2. Connect the black probe to ground (for example, to a metal part of the body).
  3. Turn on the ignition and insert the red probe into the center contact of the cigarette lighter.
  4. The voltage should be 12–14 V. If it shows 0 V - The problem is in the wiring or fuse box.
  5. Check the side contacts of the socket (should show 0 V relative to mass).

If there is no voltage:

  • Check fuse contacts in the block (possibly oxidation).
  • Inspect wiring from the block to the cigarette lighter (often chafed under the dashboard).
  • Test the circuit with a multimeter in calls (resistance should be close to 0 ohm).
💡

If the multimeter shows voltage, but the devices do not work, the problem is in the mechanical part of the cigarette lighter (for example, oxidized or bent socket contacts).

Common mistakes when replacing a fuse

Even something as simple as replacing a fuse can be done incorrectly. Common mistakes:

  • 🔧 Using the wrong fuse rating (for example, 30A instead of 15A) - this leads to a risk of fire.
  • 🔄 Installing a fuse with a bug (with a wire jumper) is a temporary solution that can burn the wiring.
  • 🔍 Ignoring the cause of burnout - if the short circuit is not eliminated, the new fuse will burn out immediately.
  • 📋 Fuse confusion (for example, replacing the cigarette lighter fuse with a fan fuse).

To avoid problems:

  • Always check with diagram on the block cover.
  • Use original fuses (For example, Bosch or Hella).
  • If the fuse blows again - don't experiment, and contact an auto electrician.
⚠️ Attention: B Nissan Almera G15 The cigarette lighter fuse is sometimes confused with a fuse ACC (nominal 10A). Their location is close, but their functions are different! Installing a 15A fuse into the socket ACC may damage the on-board computer.

Alternative ways to connect devices with a faulty cigarette lighter

If the cigarette lighter is out of order and repairs are postponed, you can temporarily connect the devices in other ways:

  • 🔌 12V socket in trunk (if included).
  • 🚗 Direct connection to battery via a fused connector (for example, for a compressor).
  • 🔋 USB ports (for charging phones, but not for high-power devices).
  • 🔌 Additional 12V socketinstalled in the service area (for example, in the glove compartment).

When connecting to a battery, be sure to:

  • Use fuse 10–15A in the chain.
  • Observe polarity (+ to +, – to –).
  • Do not connect devices with more power 180 W (for example, 220V inverters).
💡

To temporarily connect the DVR, you can use a cigarette lighter splitter with USB ports, but the total power of the devices should not exceed 15A (180 W).

FAQ: Frequently asked questions about the cigarette lighter fuse Nissan Almera G15

Can I use a 20A fuse instead of a 15A fuse?

No, it's dangerous! The 15A fuse is designed for the maximum load of the cigarette lighter. Setting 20A may result in wiring melting or fire due to a short circuit. If you need to connect powerful devices (for example, a refrigerator), install an additional 12V socket with a separate fuse.

The cigarette lighter doesn't work, but the fuse is intact. What's the matter?

There are several reasons:

  • Oxidation of contacts in the cigarette lighter socket (clean them with alcohol or WD-40).
  • Broken wiring from the fuse box to the cigarette lighter (check with a multimeter).
  • Malfunction of the cigarette lighter itself (for example, the heating coil has burned out).
  • Problems with the relay in the fuse box (rare, but it happens).

Start by checking the voltage at the socket with a multimeter.

Which fuse is responsible for the 12V socket in the trunk?

B Nissan Almera G15 2015–2019 The socket in the trunk is usually connected to a fuse PWR OUTLET rated 20A. On earlier models (2012–2014), the auxiliary outlet may not be present or may be connected to the same fuse as the cigarette lighter. Check the diagram on the block cover.

Is it possible to repair a burnt out cigarette lighter or just replace it?

If only the heating coil burns out, it can be replaced (repair kits are sold). However, in most cases it is easier and cheaper to install a new cigarette lighter - its price is about 500-1000 rubles. The main thing is not to forget to disconnect the negative terminal of the battery before replacing!

What should I do if the cigarette lighter fuse blows when the compressor is connected?

This means that the compressor is drawing too much current. Solutions:

  • Use a compressor with a lower power (up to 150 W).
  • Connect the compressor directly to the battery via terminals with a 20A fuse.
  • Install an additional 12V socket with a separate 20–25A fuse.

Do not use splitters - they increase the load on the circuit.