Rear seat in Nissan Juke the first and second generations (J10/J11) require dismantling not only when replacing upholstery or repairing fasteners, but also to access hidden elements: the fuel pump, audio system wiring, or even the spare tire in some trim levels. Unlike classic hatchbacks, the design Juke has special features: there are no traditional hinges under the seat, and the latches are hidden under plastic plugs.

Many owners are faced with a problem: how to remove the seat without damaging the plastic clips or the backrest folding mechanism? In this article - step-by-step algorithm with photos, list of necessary tools and unique techniques for models with electric folding backrest (optional for the European market). We will also look at typical mistakes that lead to broken latches or broken seat heating wires.

Preparation: Tools and Safety Precautions

Before starting work, make sure that the vehicle is on a level surface and the parking brake is activated. B Nissan Juke the rear seat is attached to the body through 4 main points (two on each side), but access to them is blocked by decorative trims. You will need:

  • 🔧 Plastic mounting spatula (for removing plugs without scratching)
  • 🔨 10 mm head with extension (for mounting bolts to the body)
  • ⚡ Screwdriver with Phillips bit T20 (for armrest screws)
  • 🧲 Magnetic holder (so as not to lose bolts in the cabin)
  • 📸 Smartphone (to fix the location of the heating wires)

If your Juke equipped with heated rear seats, mandatory disconnect the negative terminal of the battery 10 minutes before the start of work. This will prevent a short circuit if the wires are accidentally touched. In models with Bose Audio System The wiring harness for the subwoofer runs under the seat - it should not be pulled or bent.

⚠️ Attention: On versions Juke Nismo And Nismo RS the seats have additional stiffeners. When dismantling, do not apply force to the central part of the backrest - this may deform the frame.
📊 What generation of Nissan Juke do you have?
  • First (J10, 2010–2019)
  • Second (J11, since 2019)
  • Nismo/Nismo RS
  • I don't know

Step 1: Removing decorative caps

Start by removing the plastic covers that hide the mounting bolts. They are located:

  • 🔹 In front of the seat (at the feet of passengers)
  • 🔹 At the back, at the base of the back (under a small protrusion)

Pry up the plugs plastic spatula, starting from the corner. On models before 2015, the clips are fragile - if they are cracked, replace them with analogues from Nissan (article 77110-4M000). B Juke J11 (2019+) the plugs are attached with Velcro and can be removed without tools.

Under the overlays you will see:

  • 🔧 Two 10mm bolts (front)
  • 🔧 One T20 self-tapping screw (behind, under the back)
What to do if the plug is broken?

If the clip is cracked, do not try to glue it - it will not withstand the load. Buy a new one (cost ~200 rubles) or temporarily fix the plug with double-sided tape, but do not leave the bolts open: dust and moisture will get into them.

Step 2: Unscrewing the fasteners and disconnecting the wires

After removing the plugs:

  1. Unscrew front bolts 10mm head. Don't lose the washers - they have a special anti-corrosion coating.
  2. Unscrew self-tapping screw T20 behind. In some configurations there may be a plastic nut here - you need to turn it counterclockwise.
  3. Lift the seat from the front and slide it forward to release the rear latches.

If in your Juke there are heated rear seats, under it you will find power connector (orange or yellow). To detach it:

  1. Click on plastic retainer on the side of the connector.
  2. Pull the block smoothlywithout tugging - the contacts may oxidize.
⚠️ Attention: On models with Bose Audio There is a harness running under the seat to the subwoofer in the trunk. If you pull the seat too sharply, you can tear the connector from the amplifier (repair will cost ~5,000 rubles).
Juke model Seat mounting type Features
J10 (2010–2014) 4 bolts + 2 latches Rear clips are metal and may rust
J10 (2015–2019) 4 bolts + plastic clips Clips are fragile and require care
J11 (2019–present) 2 bolts + 2 screws + Velcro Electric backrest folding (optional)
Nismo/Nismo RS 6 attachment points Stiffeners, 3 kg heavier

Step 3: Removing the Power Seat (for J11)

B Nissan Juke J11 (from 2019) the option of electric backrest folding is available. If your car is equipped with it, the removal algorithm is different:

  • 🔌 Disconnect the battery (required!)
  • 🔧 Remove the plastic cover under the armrest (the motor connector is hidden there).
  • 📱 Take a photo of the location of the wires - they can easily be confused when reassembling.

The drive motor is attached to the seat frame two 8 mm bolts. After unscrewing them, carefully remove the motor along with the wiring harness. Do not pull the wires - they are soldered to the control board!

Disconnect the battery|Remove the pad under the armrest|Disconnect the motor connector|Unscrew the 2 bolts securing the motor|Take a photo of the location of the wires-->

Common mistakes and how to avoid them

Even experienced car owners make mistakes when removing the rear seat in Juke. Here are the most common:

  • 🚫 Trying to remove the seat without unscrewing the rear screw → leads to frame deformation.
  • 🚫 Using metal tools to remove plugs → scratches on the plastic.
  • 🚫 Sharp twitching of the heating connector → broken wires (repair ~3,000 rubles).
  • 🚫 Lost bolts or washers → vibrations and squeaks after installation.

If after removing the seat you find rust on bolts, process them WD-40 and replace the washers. B Juke the first generation rear clamps often rust - they can be cleaned with a metal brush and coated Litolom-24.

💡

Before reinstalling the seat, check the condition of the rubber seals on the fasteners. If they become hard or cracked, replace them (Part No. 80310-4M000). This will eliminate squeaks when moving.

Access to hidden elements after removing the seat

Now that the seat is removed, you can:

  • 🔋 Check fuel pump (hatch under the rug on the right).
  • 🔊 Get to the amplifier Bose (on the left under the seat).
  • 🔌 Check audio system connectors (a common cause of crackling noise in speakers).
  • 🚗 Replace trunk light bulb (cartridge under plastic cover).

B Juke J10 also located under the rear seat fuse box for audio system and climate control. If your radio or air conditioner does not work, check the fuses F37 (10A) And F42 (15A).

💡

On all-wheel drive (AWD) models, the rear wheel drive shaft runs under the seat. Do not place tools on it - this may damage the CV joint boots.

Reverse installation: nuances and verification

When installing the seat back, pay attention to:

  1. Latch position - they should click into place with a characteristic sound.
  2. Connecting connectors — the orange connector goes to the heating, the black connector goes to the seat belt sensor.
  3. Tightening the bolts — tightening torque 8–10 Nm (do not overtighten!).

After installation:

  1. Check your work heated seats (if any).
  2. Make sure the backrest locks in an upright position.
  3. Drive on uneven roads - there should be no squeaks or knocks.

If the backrest does not lock, check folding cable (it may jump off the guides). In models with electric drive, reset errors using the diagnostic scanner (code B2555 — faulty folding motor).

FAQ: Frequently asked questions about removing the rear seat

Is it possible to remove the seat without unscrewing the bolts?

No. B Nissan Juke the seat is bolted to the body - there are no latches, like in some European cars. If you try to remove it by force, the plastic latches on the back will break.

What to do if the bolt is rusty and cannot be unscrewed?

Process it WD-40 or liquid key for 10–15 minutes. If that doesn't help, use impact screwdriver or heat the bolt with a hair dryer (do not overheat the plastic!). As a last resort, the bolt can be drilled out, but then you will need a tap to cut a new thread.

How to understand that the heating connector is connected correctly?

When connected correctly:

  • 🔹 The heating indicator (yellow spiral) will light up on the dashboard.
  • 🔹 After 1-2 minutes, the seat will start to heat up (check with your hand).
  • 🔹 There will be no error in the diagnosis B1234 (open heating circuit).
Can the removed seat be washed with water?

You can, but with caution:

  • 🚿 Use soap solution and a soft brush.
  • 🚫 Do not direct the water jet at heating wires or connectors.
  • ☀️ Dry the seat in the sun or in a ventilated area (at least 12 hours).

If the upholstery is heavily soiled, it is better to use steam cleaner or have the seat dry cleaned.

Where can I buy replacement clips and bolts for the Juke?

Original parts can be ordered by catalog numbers:

  • 🔹 Plug clip: 77110-4M000 (~200 rub.).
  • 🔹 Mounting bolt: 08915-6040A (~150 rubles per piece).
  • 🔹 Rubber seal: 80310-4M000 (~300 rub.).

Analogues (for example, from Honda or Toyota) may not fit correctly. Buy only from authorized dealers or trusted suppliers (for example, Exist.ru or Emex).