Removing the rear seat Nissan Tiida - a task that owners face when renovating the interior, replacing upholstery or installing additional equipment. At first glance, the process seems simple, but without knowledge of the design features of the model, you can encounter difficulties: from jammed latches to damaged plastic fasteners. This article will help you figure out how to properly remove the seat without consequences for the interior.

We will look at both generations Tiida (J31 and J32), we will indicate the key differences in fastenings and share practical advice, which will save your time. For example, did you know that on versions with heated seats, you must first disconnect the power connectors? Or that in some modifications you will have to dismantle only the right side of the sofa to access the fuel pump? These and other nuances are discussed further in the material.

Preparing for dismantling: tools and safety precautions

Before you start work, prepare the necessary equipment. You will need:

  • 🔧 10 or 12 mm socket wrench (depending on year of manufacture)
  • 🔨 Plastic installation tool (for prying off the clips)
  • 🔌 Screwdriver with Phillips bit (for heating connectors)
  • 🧤 Gloves (so as not to scratch the casing)
  • 📸 Smartphone (to fix the location of the fasteners)

Pay special attention to safety: in Nissan Tiida 2007–2012 system wires run under the rear seat SRS (airbags), so before starting work, be sure to disconnect the negative terminal of the battery. Also check if there are any foreign objects in the cabin that could interfere - for example, child seats or luggage in a niche under the floor.

📊 What experience do you have in car repair?
  • Newbie - first time removing the seat
  • Amateur - I do it myself, but carefully
  • Professional - I do auto repair
  • Never repaired, only maintenance

Design features of the Tiida rear seat

Rear seat in Nissan Tiida consists of two main parts: sofa (bottom) and backrest. Depending on the configuration, their fastenings may differ:

Modification Sofa mounting type Backrest mounting type Additional items
Tiida J31 (2004–2010) 2 bolts front, 2 latches rear Locks at the bottom Heating (optional)
Tiida J32 (2010–2016) 4 bolts (2 each front and rear) Latches + bolt in the middle Seat belts with sensors
Tiida Latio (Asian version) Combined: bolts + clips Removable center armrest System ISOFIX

In models with heated seats Under the sofa there are wires going to the control unit. They should not be pulled or bent - this may lead to broken contacts. If your Tiida equipped with a system ISOFIX, pay attention to the additional metal brackets under the back: they often interfere with dismantling.

💡

Before removing the seat, take photographs of the location of the bolts and connectors. This will help avoid confusion during reassembly, especially if you are planning to replace the sheathing or repair the frame.

Step-by-step instructions: how to remove the rear seat sofa

Let's start with the bottom of the seat (sofa). Algorithm of actions:

  1. Open the rear doors and lower the seatback forward (if available on your configuration).

  2. Pry up the plastic trim at the base of the backrest using the installation tool. It is attached with 4 clips.

  3. Lift the sofa by the front edge - it should come out of the grooves. Some versions will require you to remove the bolts from the front first (see table above).

  4. If the seat does not rise, check to see if the seat belts are caught in the frame. B Tiida J32 they often block traffic.

Battery terminal disconnected|Mounts photographed|Tools at hand|No foreign objects under the seat-->

After removing the sofa, you will see a metal frame with guides. Inspect them carefully for corrosion - this is a common problem with Tiida, operated in conditions of high humidity. If you plan not to reinstall the seat for a long time, cover the guides with tape to prevent dust from entering.

⚠️ Attention: In models with fuel tank under the seat (For example, Tiida 1.6) after dismantling the sofa, access to the fuel pump hatch opens. Do not touch the pump wires without first relieving the pressure in the system!

Removing the rear seat back: nuances and difficulties

The backrest is attached differently than a sofa, and its removal requires more care. In the majority Tiida it is fixed:

  • 🔩 Two bolts at the bottom (under the decorative trim)
  • 🔗 Latches on the sides (they need to be pressed out with a screwdriver)
  • 🔌 Heating connector (if available)

To remove the backrest:

  1. Unscrew the bolts at the bottom (they may be hidden under plastic plugs).

  2. Disconnect the side latches by carefully prying them up with a tool. Do not use excessive force - plastic is fragile!

  3. If the backrest is heated, unplug the power connector (usually located on the right side).

  4. Lift the backrest up and pull it out of the grooves.

B Tiida J32 with the system ISOFIX the backrest may have additional attachments for child seats. They need to be unscrewed separately. Also note central armrest — in some versions it is removable and fastened with two clips.

What to do if the latch is broken?

If the plastic back latch cracks during removal, do not try to fix it with glue - this is a temporary solution. Better order a new part using the catalog number 80310-4M000 (for J31) or 80310-4M100 (for J32). The cost of the original latch is about 300–500 rubles, but it is guaranteed to last longer than its universal counterparts.

Common mistakes and how to avoid them

Even experienced car owners sometimes make mistakes when removing the rear seat. Here are the most common:

  • 🔧 Ignoring battery disconnection - This may cause the airbags to deploy or cause a short circuit.
  • 🔨 Using metal tools for prying up the clips - they scratch the plastic. Use only plastic spatulas.
  • 🔩 Lost bolts or clips — without them it is impossible to properly fasten the seat back. Store them in a separate box.
  • 🔌 Mixing up connectors heating - this can damage the control unit.

Another typical problem is plating damage during dismantling. To avoid this, do not pull the seat by the fabric, but only grab the metal frame. If the sheathing is already torn, you can temporarily fix it with tape or a stapler, but it is better to immediately plan a replacement.

⚠️ Attention: B Nissan Tiida With leather interior trim, when the seat is removed, the adhesive that attaches the trim to the foam often peels off. If you notice this, use a special adhesive for car dealerships (for example, Loctite 406).

Reinstallation: how to assemble everything correctly

Reinstalling the seat requires no less care than removing it. Follow this order:

  1. Check that all clips and bolts are in place. If some are lost, don't improvise - buy new ones.

  2. Install the backrest starting from the top grooves. Make sure it clicks into place.

  3. Secure the bolts in the lower part of the backrest (tightening torque: 8–10 Nm).

  4. Connect the heating connectors (if any) and check their operation before final assembly.

  5. Install the sofa starting from the rear grooves, then secure with bolts at the front.

After assembly, check:

  • 🔍 Seat belt travel - they should not cling to the seat.
  • 🔊 Extraneous sounds — creaks or knocks indicate incorrect installation.
  • 🔥 Heating work (if there is one) - turn it on at maximum power.
💡

If after installation the seat “walks” or falls through, check the condition of the rubber dampers under the sofa. B Tiida older than 2010, they often dry out and require replacement (article no. 80350-4M000).

When is it necessary to remove the rear seat?

Removing the rear seat Nissan Tiida may be needed in several cases:

  • 🔧 Repair or replacement of sheathing (torn fabric, frayed leather).
  • 🛠️ Installation of additional equipment: subwoofer, alarm, DVR with rear camera.
  • ⛽ Replacing the fuel pump (on models with an under-seat tank).
  • 🔋 Electrical wiring diagnostics (for example, when the heating is not working).
  • 🧹 Deep interior cleaning (removing dirt from under the seats).

If you are planning subwoofer installation, please note that in Tiida there is not enough space under the sofa - usually only a compact model with a body no deeper than 20 cm can fit there. For larger systems, you will have to modify the floor or use the trunk.

When replacing the fuel pump remember: after removing the seat, you must clean the tank flap from dirt so that it does not get into the fuel system. Also check the condition of the rubber seal on the hatch - if it is cracked, replace it (part number 17352-4M000).

FAQ: answers to frequently asked questions

Is it possible to remove only part of the rear seat (for example, the right side)?

Yes, in Nissan Tiida the sofa consists of two independent parts (left and right), each of which is attached separately. This is convenient if you only need to get to the fuel pump (it is located under the right side) or run wires for equipment. However, the backrest can only be removed entirely.

What is the tightening torque for the seat bolts?

For sofa bolts, the recommended tightening torque is - 10–12 Nm, for the back - 8–10 Nm. Exceeding these values can lead to thread stripping, especially if the bolts are rusty. In this case, pre-treat them with a penetrating lubricant (for example, WD-40).

What should I do if the seat squeaks after installation?

Creaking usually occurs due to:

  1. Poorly tightened bolts - check their torque.
  2. Worn rubber dampers - replace them.
  3. Friction of the casing on plastic parts - treat the contact points with silicone grease.

If the squeak does not disappear, remove and reinstall the seat and check all fasteners.

Where can I buy original clips and bolts for Tiida?

Original spare parts can be ordered from official dealers Nissan or in trusted online stores (for example, Exist.ru, Autodoc). An alternative is universal clips from 3M or Hella, but they may not fit correctly. Always check the catalog for your vehicle's VIN.

Can the removed seat be washed with water?

Yes, but with caution:

  • Use cold water and a soft brush.
  • Don't get it wet foam base - It takes a long time to dry and can become moldy.
  • For leather upholstery, use special cleaners (for example, Leather Cleaner from Sonax).
  • After washing, dry the seat in the sun or with a fan.