Replacing the oil filter with Nissan Teana - a procedure that many car owners prefer to perform on their own. However, even experienced drivers sometimes get lost when trying to find a filter in the engine compartment. In this article we will not only show exact location of the oil filter on models J31 (2003–2008) and J32 (2008–2013), but we will also analyze the nuances of replacing it, typical mistakes and give practical advice.

Feature Teana — compact placement of components under the hood, which can make access to the filter difficult. If you've never changed the oil on this car, prepare yourself for what's required special puller and possibly removing the crankcase protection. We will describe the process in detail for engines VQ25DE (2.5 l) and VQ35DE (3.5 l), as their design has key differences.

Where is the oil filter located on Nissan Teana J31 and J32?

On Nissan Teana the oil filter is located in front of the engine, at the bottom of the cylinder block. The exact location depends on the engine type:

  • 🔧 VQ25DE (2.5 l): The filter is moved closer to the front bumper, under the generator. Access to it is difficult due to the cooling system pipes.
  • 🔧 VQ35DE (3.5 l): the filter is located slightly to the right (in the direction of travel) and lower, next to the oil pan. This is where the crankcase protection gets in the way.

The photo below shows the location for VQ35DE (view from below the car):

Visual references:

  • 📍 The filter looks like a cylindrical black or silver body with a diameter of ~7–8 cm.
  • 📍 An oil line (thin tube or threaded connection) is suitable for it.
  • 📍 On J32 the filter can be covered with a plastic cover (this must be removed).

To see the filter, sometimes you need remove crankcase protection (4 bolts per J31, 6 bolts per J32). On models with VQ35DE The air conditioner tube may also be in the way - it should be carefully moved to the side.

📊 What engine do you have in your Nissan Teana?
  • VQ25DE (2.5 l)
  • VQ35DE (3.5 l)
  • Other (specify in comments)
  • I don't know

Step-by-step instructions: how to get to the oil filter

Before starting work, prepare the following tools:

  • 🔧 Oil filter puller (chain or cup 64 mm for VQ25DE, 76 mm for VQ35DE).
  • 🔧 14 mm wrench (for drain plug).
  • 🔧 10 mm socket wrench or socket (to protect the crankcase).
  • 🔧 Funnel and container for used oil (minimum 5 l).

Step 1. Preparing the car

  1. Stop the engine and let the oil drain into the pan (10–15 minutes).
  2. Raise the car on a lift or drive it into a viewing hole. On Teana J32 With crankcase protection without a pit, it is almost impossible to replace the filter!
  3. Remove the crankcase protection (if equipped) - it is secured with 10 mm head bolts.

Step 2: Drain the oil

Unscrew the drain plug (14 mm wrench) and drain the oil into a container. On VQ35DE The plug is located closer to the rear of the pan, on VQ25DE - in the middle.

Step 3. Removing the filter

Now the hardest part is removing the filter. On Teana he often gets stuck, so:

Clean the filter from dirt with a rag|Apply penetrating lubricant (WD-40) to the threads|Use a puller, not your hands|Place a container - ~100 ml of oil will flow out of the filter-->

On VQ25DE the filter unscrews counterclockwise, but due to limited space, a puller extension may be required. On VQ35DE the filter is sometimes covered with a plastic cover - you need to remove it by pulling it up.

💡

If there is no puller, you can try to pierce the filter with a screwdriver and unscrew it like a lever. But this method is risky - you can damage the oil line!

Which oil filter is suitable for Nissan Teana?

Original filter from Nissan has an article number 15208-9F600 (for VQ25DE) and 15208-9F60A (for VQ35DE). However, many car owners choose analogues that are cheaper but not inferior in quality.

Brand Article Applicability Price, ₽
Nissan (original) 15208-9F600 VQ25DE (J31/J32) 1 200–1 500
Mann W 712/92 VQ25DE, VQ35DE 600–800
Bosch 0 451 103 336 VQ35DE 700–900
Framm PH7317 VQ25DE 400–500
Sakura C-1008 Both engines 300–400

When choosing a filter, pay attention to:

  • 🔍 Thread size: on VQ25DE — M20×1.5, on VQ35DE — M22×1.5.
  • 🔍 Presence of a check valve (important to prevent oil starvation at startup).
  • 🔍 The quality of the rubber seal - it should be elastic, without cracks.
💡

Don't skimp on the filter! Cheap analogues may not withstand the oil pressure in the system VQ35DE (up to 4.5 bar), which will lead to rupture of the housing.

Typical mistakes when replacing the oil filter on Teana

Even experienced car owners make mistakes that later lead to serious problems. Here are the most common:

⚠️ Attention! If, after replacing the filter, the light on the instrument panel lights up Check Engine with code P0520 (faulty oil pressure sensor), most likely the filter is installed incorrectly or is leaking.

Error 1. Under-twisted or over-twisted filter

The filter must be screwed on by hand until it stops, and then pull the puller 3/4 turn. The constriction leads to:

  • 🔧 Deformation of the sealing ring → oil leaks.
  • 🔧 Damage to the threads on the cylinder block (repair will cost 5-7 thousand ₽).

Error 2: Ignoring the O-ring

On some filters (for example, Mann W 712/92) the ring is included, but it is needed lubricate with engine oil before installation. Otherwise:

  • 🔥 The ring sticks to the block, and the next time you replace it, the filter will not come off.
  • 💧 A micro-leak of oil occurs, which is difficult to notice immediately.

Error 3. Replacement without flushing the system

If you switch to another oil (for example, with 5W-30 on 5W-40), it is necessary to flush the system with a special liquid. Without rinsing:

  • 🛢️ Old oil will mix with new oil, worsening its properties.
  • 🔥 Possible deposits in the oil channels leading to oil starvation.
What to do if the filter does not unscrew?

If the puller is slipping, try:

1. Treat the thread with WD-40 and wait 10 minutes.

2. Use a 3-jaw puller instead of a chain puller.

3. As a last resort, drill the filter and screw a bolt into it to unscrew it like a lever.

**Warning**: When drilling there is a risk of damaging the oil line!

When to change the oil filter: regulations and signs of wear

According to the regulations Nissan, oil filter on Teana is changing every 10–15 thousand km or once a year (whichever comes first). However, there are factors that shorten this period:

  • 🚗 Aggressive riding (frequent acceleration/braking) - the filter clogs faster.
  • 🏙️ City mode (constant traffic jams) - the oil overheats more often.
  • 🌡️ Extreme temperatures (frost below -25°C or heat above +35°C).

Signs that the filter needs replacing:

  • 🔴 The panel lights up Check Engine with code P0520 (low oil pressure).
  • 🔴 The oil in the system quickly darkens (even after a recent change).
  • 🔴 When starting the engine you can hear metallic knock (a sign of oil starvation).
  • 🔴 Oil spots appear under the car (leaking from under the filter).

If you notice any of these symptoms, don't delay replacement - a worn filter can lead to rotation of the liners (engine overhaul will cost 100+ thousand rubles).

Tips for choosing oil for Nissan Teana after replacing the filter

After installing a new filter, it is critical to fill the right oil. For VQ25DE And VQ35DE Oils with the following specifications are suitable:

  • 🛢️ Viscosity: 5W-30 (in winter), 5W-40 or 10W-40 (in summer).
  • 🛢️ Standard: API SN or ILSAC GF-5.
  • 🛢️ Volume: 4.5 l for VQ25DE, 5.0 l for VQ35DE.

Recommended brands:

  • 🏆 Nissan Original Oil 5W-40 (article KE900-90132) is the optimal choice for warranty service.
  • 🏆 Mobil 1 ESP 5W-30 - Suitable for harsh operating conditions.
  • 🏆 Liqui Moly Top Tec 4200 5W-30 - Improves wear protection.

After changing the oil and filter necessarily:

  1. Start the engine and let it idle for 2-3 minutes.
  2. Check the oil level with a dipstick (should be between MIN And MAX).
  3. Inspect the filter for leaks (especially in the first 100 km).

FAQ: Frequently asked questions about the oil filter on Nissan Teana

Is it possible not to change the filter when changing the oil?

No! The filter becomes clogged with wear products and loses throughput. If you leave the old filter, the new oil will quickly become contaminated and the pressure in the system will drop. This will lead to accelerated engine wear.

What puller is needed for the filter on Teana J32?

For VQ25DE Suitable cup puller 64 mm, for VQ35DE - by 76 mm. Alternative: chain puller with adjustable diameter (e.g. KING TONY 2035).

What should I do if the oil pressure light comes on after replacing the filter?

The reasons may be the following:

  1. The filter is not screwed in properly or the O-ring is damaged.
  2. There is little oil in the system (check the level with a dipstick).
  3. The oil pressure sensor is faulty (diagnostics required).
Actions: Turn off the engine, check the filter for leaks and oil level. If the lamp does not go out, contact service.

Can I use an Infiniti filter on Teana?

Yes, many filters from Infiniti (for example, for Infiniti G35 with engine VQ35DE) are fully compatible with Nissan Teana J32. The main thing is to check the article number and dimensions.

How much oil remains in the filter when changing?

~100–150 ml of oil remains in the filter. Therefore, when adding new oil, first fill in 4.0 liters (for VQ35DE), then add to the level MAX after starting the engine.