Nissan Sunny is a legendary Japanese sedan that has gained popularity due to its reliability and unpretentiousness. However, when replacing rims or tires, owners are often faced with the question: what is the bolt pattern? Nissan Sunny? An error in choosing parameters can lead to vibrations, premature wear of wheel bearings, or even an emergency.

In this article we will analyze in detail bolt pattern for all generations Sunny (B13, B14, B15), including parameters PCD, ET (departure), DIA (center hole) and the diameter of the mounting bolts. You will also find compatibility tables with other models Nissan and recommendations for selecting disks.

What is a bolt pattern and why is it important for Nissan Sunny

Bolt pattern (or PCD — Pitch Circle Diameter) is the diameter of the circle on which the wheel mounting holes are located. For Nissan Sunny this parameter is critical: incorrect PCD will lead to the fact that the disk will not sit tightly on the hub, and the bolts will be tightened skewed. Consequences:

  • 🔧 Steering wheel vibration at speeds above 60 km/h due to imbalance.
  • 🚗 Accelerated wear wheel bearings and ball joints.
  • 💥 Risk of wheel separation during emergency braking (in critical cases).

Except PCD, when selecting disks for Sunny take into account:

  • 📏 ET (departure) — the distance from the mating plane of the disk to its center. A deviation of more than ±5 mm changes the load on the suspension.
  • ⭕ DIA - diameter of the central hole. If it is smaller than the hub, the disc will not fit; if more, centering rings will be required.
  • 🔩 Bolt thread - for Sunny this is usually M12×1.25.
⚠️ Attention: Discs with unsuitable PCD you can “pull” it onto the hub by force, but this will lead to deformation of holes and uneven tightening of bolts. This kind of “repair” is dangerous!

Nissan Sunny bolt pattern by generation: table of parameters

Bolt pattern parameters Nissan Sunny depend on the generation and year of manufacture. Below is a table with exact data for the most common modifications:

Generation Years of manufacture PCD (bolt pattern) ET (reach), mm DIA (center hole), mm Bolt thread Disc diameter, inches
Nissan Sunny B13 1986–1990 4×100 35–45 59.1 M12×1.25 13–15
Nissan Sunny B14 1990–1995 4×100 38–45 66.1 M12×1.25 14–16
Nissan Sunny B15 1995–2006 4×114.3 35–45 66.1 M12×1.25 14–17
Nissan Sunny N16/N17 (for Asian markets) 2000–2006 4×114.3 38–50 66.1 M12×1.25 15–17

Please note: Sunny B15 and later models switched to bolt pattern 4×114.3, which coincides with Nissan Almera N16 And Primera P12. This expands the choice of disks, but requires precise selection ET And DIA.

📊 What generation of Nissan Sunny do you have?
  • B13 (1986–1990)
  • B14 (1990–1995)
  • B15 (1995–2006)
  • Other

How to measure the bolt pattern on a Nissan Sunny yourself

If you are not sure about the parameters of your Sunny, you can measure the bolt pattern yourself. You will need:

  • 📏 Ruler or caliper.
  • 🔧 Wheel removal key (if you need to remove the disk).

Method 1: Measure between adjacent bolts

For discs with 4 holes (like Sunny):

  1. Measure the distance between the centers of two adjacent bolts - get the value X.
  2. Multiply X at 1.414 - this will be PCD.

Example: If the distance between the bolts is 70.7 mm, then PCD = 70.7 × 1.414 ≈ 100 mm (bolt pattern) 4×100).

Method 2: Measuring the diameter of a circle

Remove the disk and measure the diameter of the circle around which the holes are located. This is what will happen PCD.

⚠️ Attention: On Sunny B15 And N16 bolt pattern 4×114.3 often confused with 4×100 due to visual similarity. Check for sure!

Measure the PCD (bolt pattern) of your Sunny|Check the ET (offset) with the recommended values|Check the center hole diameter (DIA)|Make sure the bolt threads are compatible|Check with the seller about the warranty-->

Wheel compatibility: which models are suitable for Nissan Sunny

Discs from other models Nissan and even some foreign cars may be suitable for Sunny, if the key parameters match. Below is a list of compatible cars:

  • 🚗 Nissan Almera N16 (2000–2006) — 4×114.3, ET 38–45, DIA 66.1.
  • 🚗 Nissan Primera P12 (2002–2008) — 5×114.3 (not suitable for Sunny, but sometimes they are mistakenly confused!).
  • 🚗 Nissan Pulsar N15/N16 — 4×100 (for Sunny B13/B14).
  • 🚗 Mitsubishi Lancer 9 (2000–2007) — 4×114.3, but verification required ET.
  • 🚗 Toyota Corolla E12/E15 — 4×100 (only for Sunny B13/B14).

Important: even if there is a coincidence PCD check:

  • 🔄 ET (departure) — a deviation of more than ±5 mm impairs controllability.
  • ⚙️ DIA - if the central hole is larger, use centering rings.
  • 🔧 Bolt thread - for Sunny standard M12×1.25, but on some disks it may be M12×1.5.
💡

If you buy used discs, check them for runout: place the disc on a flat surface and spin it. Any play or “figure eight” is a sign of deformation.

Common mistakes when selecting wheels for Nissan Sunny

Even experienced car owners sometimes make mistakes when choosing wheels. Let's look at typical mistakes and their consequences:

  1. Confusion between 4x100 and 4x114.3

    On Sunny B15 often try to install disks from Sunny B14 (4×100), which leads to inability to fully tighten bolts. Visually, the difference of 14.3 mm is invisible, but critical!

  2. Ignore departure (ET)

    Discs with ET 20 instead of recommended 35–45 will move the wheel outward, increasing the load on the wheel bearing and suspension arms.

  3. DIA misalignment without centering rings

    If the center hole of the disc is larger than the hub, the wheel will "lobble" in the seat even if the bolts are tightened. This leads to vibrations at speed.

  4. Using bolts of the wrong length

    Bolts that are too long will rest against the brake disc, and short bolts will not provide reliable fixation.

⚠️ Attention: On Sunny B15 with engines GA16DE or QG18DE sometimes they install disks from Nissan Primera (5×114.3) after reworking the hubs. This illegal modification, which does not pass inspection!

How to choose wheels for tuning Nissan Sunny

If you are planning to tune your Sunny, not only aesthetic perception is important, but also technical compatibility. Let's look at the key points:

  • 🔥 Disc width: Standard for Sunny - 5.5–6.5J. Increasing to 7J is possible, but will require rolling out the arches or using spacers (which is unsafe!).
  • 🎨 Design: For retro models (B13/B14) popular style wheels Work Equip or Enkei 92. For B15 Modern cast or forged wheels are suitable.
  • 🔄 Departure (ET): Recommended for lowered suspension ET 30–35so that the wheel does not rub against the fender liner.

Example of successful combinations:

  • 🚘 Sunny B14 + disks 15×6.5J ET38 with rubber 195/50R15 - classic retro style.
  • 🚘 Sunny B15 + disks 17×7J ET35 with rubber 205/40R17 — aggressive sporty look.

Before purchasing please check:

  • 📋 Compatible with brake system (on Sunny B15 Not all discs with rear drum brakes R17 will do!).
  • 🔧 Necessity of use spacers (if ET does not fit).
What happens if you install disks with the wrong ET?

Enlarged ET (for example, 50 instead of 35) will move the wheel inside the arch, which will lead to friction with the suspension or body when cornering. Reduced ET (eg 20) will push the wheel outwards, increasing the risk of damage to the wheel arch liners and reducing handling at high speeds.

Where to buy wheels for Nissan Sunny: proven options

When purchasing discs for Sunny It is important to choose a reliable seller to avoid counterfeits or mismatched parameters. Let's look at the best options:

  • 🛒 Official Nissan dealers - guarantee of original parameters, but high price.
  • 🌍 Online stores:
    • KolesaDarom, ShinaGuide — wide range and filter by PCD/ET/DIA.
    • Avito, Drom — used wheels at low prices, but require careful inspection.
  • 🏗️ Local tire shops — often there are used wheels in good condition.

Buying tips:

  • 🔍 Check it out markings on the disc (For example, 6.5J×15 H2 4×100 ET38 D66.1).
  • 📄 You require a certificate of conformity (especially for alloy wheels).
  • 💬 Read reviews about the seller - at Avito or Drom scammers are common.
⚠️ Attention: When purchasing used drives, pay attention to:
  • 🔧 Traces of corrosion on the rim (cracks are especially dangerous!).
  • 🔄 Beating when scrolling (indicates deformation).
  • 🔥 Traces of “welding” are a sign of previous repairs after an accident.
💡

When purchasing discs for Nissan Sunny Always check the parameters with the bolt pattern chart. Even visually identical disks may have different PCD or ET, which will make them unsuitable for installation.

FAQ: Frequently asked questions about the Nissan Sunny bolt pattern

Is it possible to install wheels from Nissan Almera N16 on Sunny B15?

Yes, if the parameters match: PCD 4×114.3, ET 38–45, DIA 66.1. However, check the width of the rim - Almera N16 often put 6.5J, which may require rolling out the arches on Sunny.

What should I do if the center hole of the disc is larger than the one on the hub?

Use centering rings (hubs) of the appropriate diameter. For example, if Disc DIA 73.1 mm, and the hub Sunny B15 — 66.1 mm, need a ring 73.1→66.1.

What bolts are needed for wheels on Sunny B14?

Standard bolts - M12×1.25 25–28 mm long (depending on the thickness of the disc). Alloy wheels sometimes require bolts with cone fit (check with the seller).

Is it possible to install wheels with a 4×100 bolt pattern on the Sunny B15 (4×114.3)?

No! The difference of 14.3 mm makes installation impossible without reworking the hubs. Even if you “pull” the disk by force, the bolts will be tightened unevenly, which will lead to vibrations and risk of wheel separation.

What is the maximum ET deviation allowed for the Sunny?

Recommended deviation is ±5 mm from the standard value. For example, if standard ET 38, you can install discs with ET 33–43. A larger deflection will worsen handling and increase the load on the suspension.