Removing the rear seat Nissan Note (first and second generation, indexes E11 And E12) is a task that owners face when repairing electronics, cleaning the interior, or installing additional equipment. At first glance, the procedure seems simple, but there are pitfalls here: from hidden fasteners to the risk of damaging the casing or folding mechanisms. In this article we will look at step-by-step algorithm removing the seat, we will list the necessary tools and tell you how to avoid common mistakes.

Feature Nissan Note - compact interior and specific design of the rear sofa, which in basic versions is mounted on 4 main brackets, and in configurations with the function Easy Fold (quick folding) has additional latches. If you plan to remove the seat for access to the fuel pump through the passenger compartment (on models with petrol engines HR15DE/HR16DE), it is important to consider the location of technological hatches and the order in which the wiring is disconnected.

Preparation: Tools and Safety Precautions

Before starting work, make sure you have everything you need. Unlike many cars, where a screwdriver is enough to Nissan Note Specialized tools may be required—especially if the seat is powered or heated.

  • 🔧 Tools:
    • Socket wrench or socket 10 mm (for fastening bolts)
    • Flat blade screwdriver (for plastic clips)
    • Plastic puller or spatula (so as not to damage the casing)
    • Multimeter (if you have to work with electrical equipment)
  • 🚗 Vehicle preparation:
    • Place the car on a flat surface, lock the handbrake
    • Disconnect the negative terminal of the battery (if you plan to work with the wiring)
    • Move the front seats to the full forward position for comfort

Important: on models with systems NissanConnect or Around View Monitor Antenna or sensor cables may run under the rear seat. Before pulling the seat up, visually check for wires attached to the bottom of the seat.

⚠️ Attention: If your Nissan Note equipped heated rear seats, before dismantling, be sure to disconnect the power connectors. The contacts of the heating elements are often located under the central part of the sofa and can be damaged if removed carelessly.
📊 Why do you remove the back seat?
  • Subwoofer installation
  • Electronics repair
  • Interior cleaning
  • Access to the fuel pump
  • Other

Rear seat design Nissan Note: what you need to know

Rear seat in Nissan Note consists of two main parts:

  1. Lower part (sofa) — attached to the body with 4 bolts (2 on each side) and may have additional fasteners for the function Easy Fold.
  2. Backrest - in most versions it is removable, but on some modifications (for example, with ISOFIX) has a rigid attachment to the body.

Features of fastenings depending on the configuration:

Equipment Sofa mounting type Additional items
Visia (basic) 4 bolts per 10 mm No
Acenta with Easy Fold 4 bolts + 2 plastic clips Folding cables
Tekna heated 4 bolts + metal brackets Heating element connectors, seat occupancy sensor
Nismo (sports) 4 bolts + reinforced brackets Additional stiffening ribs

On models with gasoline engines located under the rear seat fuel pump access hatch (on diesel versions - to the filter). If your goal is to repair the fuel system, keep in mind that after removing the seat you will need to remove the protective cover (attached with 3 self-tapping screws).

How to determine the type of mount on your model?

Look under the front of the sofa from the rear passengers' feet. If plastic latches are visible, you have a system Easy Fold. If only metal brackets are a standard mount.

Step-by-step instructions: how to remove the rear seat

The dismantling algorithm depends on the type of fastening, but the general sequence of actions is as follows:

  1. Turn off the power (if there is heating or electronics). The connectors are usually located under the central part of the sofa.
  2. Move the front seats forward and recline their backs to create more space.
  3. Find the mounting bolts — they are hidden under plastic plugs in the front part of the sofa (from the side of the passengers’ feet).
  4. Unscrew the bolts socket wrench on 10 mm. On models with Easy Fold Pre-squeeze the plastic clips with a screwdriver.
  5. Raise the sofa behind and slide it forward to release the latches.

On vehicles with system ISOFIX The seat back can be rigidly fixed. In this case:

  • Locate the release levers at the bottom of the backrest (usually marked with a pictogram).
  • Pull the levers up and at the same time push the backrest forward.
  • If the backrest does not give way, check that the trunk locks are not locked (on some models they are connected to the folding mechanism).

Important: on Nissan Note with panoramic roof Drainage hoses may run under the backrest trim. Do not pull the backrest sharply upward - first make sure that the hoses are not strained.

The battery terminal is disconnected (if working with electrics)|The front seats are moved forward|Tools are prepared (10 mm wrench, screwdriver)|Checked for the absence of wires under the seat-->

⚠️ Attention: On models 2013–2017, it can be installed under the rear seat shock sensor (for system Nissan Safety Shield). If dismantled carelessly, it can easily be damaged, which will lead to an error. Airbag on the dashboard.

Common mistakes and how to avoid them

Even experienced car owners sometimes make mistakes when removing the rear seat. Here are the most common ones and how to prevent them:

  • 🔨 Broken threads on bolts - occurs if you use the wrong tool (for example, an open-end wrench instead of a socket wrench). Always check the head size (10 mm for Note).
  • 🔌 Damage to heating connectors — before dismantling, take a photo of the location of the contacts or mark them with a marker.
  • 🚪 Forgotten fasteners Easy Fold — if you do not press the plastic latches, you can break the folding mechanism.
  • 💺 Sharp tugging of the back - on models with ISOFIX this can lead to deformation of the guides.

Another common problem is loss of plastic plugs bolts They often fall out when unscrewed and get lost in the cabin. To avoid this, use a magnetic fastener tray or tape the plugs to the seat before starting work.

If after installing the seat back you find that it dangles or creaks, check:

  • Are all bolts tightened (torque - 20 Nm).
  • Are any foreign objects (such as coins or cables) caught under the brackets?
  • The integrity of rubber dampers (they can harden and crumble over time).
💡

If the bolts are stuck and will not come off, spray them with penetrating lubricant (for example, WD-40) and wait 10–15 minutes. Do not use excessive force as this may cause the edges to break.

What to do after removing the seat: access to the fuel pump and other components

If your goal is fuel pump repair or replacement, after removing the seat, follow these steps:

  1. Remove protective cover (attached with 3 self-tapping screws for a Phillips screwdriver).
  2. Disconnect pump power connector (usually black with an orange retainer).
  3. Loosen up fuel pipe clamps and remove them, first placing a container for remaining gasoline.
  4. Unscrew pump pressure ring (you will need a special puller or a homemade device made from a metal strip).

On diesel versions Nissan Note (engine K9K) located under the seat fuel filter. To replace it:

  • Disconnect the water in fuel sensor connector.
  • Loosen the hose clamps (use a wrench on 8 mm).
  • Remove the filter by draining the remaining diesel fuel into the prepared container.

Important: When working with the fuel system, observe fire safety precautions. Do not smoke near your car and keep a fire extinguisher handy. Also note that after disconnecting the fuel pump, the engine may not start the first time - it will take several attempts to prime the system.

💡

On petrol Nissan Note with engines HR15DE/HR16DE The fuel pump is integrated into a module with a level sensor. When replacing it, be sure to reconfigure the fuel indicators through the diagnostic scanner (for example, Launch X431), otherwise the pointer on the dashboard will lie.

Reinstalling the seat: nuances and verification

Installing the rear seat is done in reverse order, but there are a few key points:

  1. Check the condition of the fasteners — if bolts or brackets are deformed, replace them.
  2. Make sure the electrical connections are correct (if there is heating or sensors).
  3. Adjust the seat position - it should fit snugly to the body without gaps.
  4. Check the operation of the mechanisms:
    • Folding function (Easy Fold).
    • Fasteners ISOFIX (if any).
    • Heating (if available).

After installation, sit in the back seat and rock from side to side to make sure there are no gaps. If the seat sags or creaksMost likely, the bolts are loose or the rubber gaskets are damaged. In this case:

  • Tighten the fasteners firmly 20 Nm.
  • Replace the damping rubber bushings (part number for Note E12 — 84513-4M000).
  • Check to see if any foreign objects have fallen under the brackets.

On models with systems NissanConnect After removing the seat, the antenna settings may be lost. If, after installing it back, radio reception deteriorates or stops working Bluetooth, reset your media settings via the menu Settings → System → Reset.

Frequently asked questions about removing the rear seat Nissan Note

Is it possible to remove the rear seat? Nissan Note without tools?

No, for dismantling you will definitely need a socket wrench or socket 10 mm. The fastening bolts have a high tightening torque, and it will not be possible to unscrew them with a screwdriver or pliers. Exception - models with the system Easy Fold, where you can press the plastic clips manually, but in this case, you will need a tool to completely remove the seat.

How to remove the back of the rear seat if it does not recline?

On some versions Nissan Note (for example, with ISOFIX) the backrest is rigidly fixed. To remove it:

  1. Locate the release levers at the bottom of the backrest (usually hidden under plastic caps).
  2. Pull the levers up and at the same time push the backrest forward.
  3. If the backrest does not give way, check whether the trunk locks are locked (they may be connected to the folding mechanism).

On models without levers, the backrest can be mounted on bolts hidden under the casing. In this case, you will need to remove the casing or contact service.

What to do if the light comes on after installing the seat back Check Engine?

This can happen if the fuel sensor connectors or injection system wiring were damaged during dismantling. Procedure:

  1. Check if the fuel pump connector is connected (the orange latch should click into place).
  2. Make sure that the wires going to the fuel level sensor are not damaged.
  3. Reset the error using a diagnostic scan tool or by disconnecting the battery terminal for 10 minutes.

If the error remains, contact a diagnostician - the sensor itself or the fuel module may be damaged.

What is the tightening torque for the seat bolts?

For all rear seat mounting bolts on Nissan Note (including models with Easy Fold) the tightening torque is 20 Nm. Exceeding this value can lead to thread failure in the body, and insufficient tightening can lead to backlash and squeaks.

Can the removed seat be washed with water?

Yes, but with reservations:

  • Do not use solvent based detergents (acetone, gasoline) - they will damage the casing.
  • Avoid direct contact of water with mechanisms (especially if there is heating or electronics).
  • After washing, dry the seat thoroughly, especially foam paddingto avoid mold.

Best used for cleaning foam car shampoos and a soft brush. If the upholstery is leather, apply leather conditioner after washing.