Regular maintenance is the key to long service life for your car's engine. For owners Nissan Qashqai One of the most important procedures is the timely replacement of the oil and filter element. Ignoring this requirement can lead to accelerated wear of the piston group, loss of power and costly repairs in the future.
The replacement process is not particularly difficult and can be done even by a novice car owner with a minimum set of tools. However, there are nuances that are specific to the body Qashqai different generations that must be taken into account to avoid leaks or damage to threaded connections. Properly selected consumables and careful work performance will ensure the cleanliness of the lubrication system.
Choosing the right oil filter for Nissan Qashqai
Before starting work, you need to decide which element you plan to install. There are a huge number of offers on the auto parts market, ranging from budget analogues to original solutions from the manufacturer. For series engines MR20 And M9R, most common in Nissan Qashqai, it is critical to select a filter with the correct throughput parameters.
Original filter Nissan (part number often starts with 15208) is considered a quality standard, since it has passed all factory tests for compatibility with specific motors. However, there are also quality alternatives from trusted brands, such as Mahle, Man or Ufi, which often exceed the original in terms of filtration resource. The main attention should be paid to the quality of the O-ring, which should not dry out or become deformed during installation.
It is important to check the contents of the new part. In some cases, the kit does not include a key for unscrewing the old element or an additional sealing gasket for the drain plug. The absence of these little things can turn a quick replacement into a long search for tools at the nearest store.
- 🔍 Always check the part number on the package before purchasing to avoid fakes.
- 🛠️ Make sure that the rubber seal of the new filter is lubricated with clean oil before installation.
- 📦 Check the integrity of the filter housing for dents or cracks that could lead to rupture.
Necessary tools and workplace preparation
To perform the work efficiently, you will need to prepare a certain set of tools and consumables. The standard set of keys is not always suitable for accessing the filter on some versions Nissan Qashqai, especially if the engine has complex crankcase protection. You will need a 17mm socket wrench or socket for the drain plug and a specialized oil filter puller.
The puller can be a cup wrench, chain grip, or belt type. For Nissan Qashqai It is often most convenient to use a cup wrench of the appropriate diameter, as it provides a secure grip even in hard-to-reach places. Also, do not forget to prepare a container for draining used oil with a volume of at least 5 liters.
The workplace should be level and comfortable. If you are doing work in a garage, make sure there is adequate lighting. When working outside, choose dry weather to prevent dirt and water from getting into the engine during replacement. Be sure to have rags and gloves to protect your hands from hot oil and chemicals.
☑️ Tools for filter replacement
Step-by-step instructions for dismantling the old element
Before starting work, the engine must be warmed up to operating temperature, but not overheated. Warm oil has a lower viscosity and flows better from the sump, taking with it more wear products. Drive the car into a viewing hole or overpass, turn on the handbrake and place chocks under the front wheels for safety.
Open the hood and locate the engine filler neck to remove the cap. This will speed up the oil draining process and prevent the formation of a vacuum in the system. Next, go under the car and locate the oil pan drain plug. Place the container and carefully unscrew the cap, being careful as the oil may be very hot.
After the bulk of the oil has drained, you can begin to unscrew the old filter. It is usually located at the bottom of the engine, sometimes hidden by a protective cover. Use a puller to loosen the tightness. If the filter is stuck, do not use excessive force to avoid damaging the threads or pan body.
- 🔥 Let the oil cool to a safe temperature to avoid burns when draining.
- 🧽 Prepare rags in advance, as some oil will inevitably spill when unscrewing the filter.
- 🔧 If the filter does not work, try warming it with a construction hairdryer, but do not overheat the plastic parts.
What to do if the filter is stuck?
If a standard puller fails, you can try using a chain wrench, but be very careful not to damage adjacent parts. In extreme cases, sometimes you have to carefully pierce the filter housing with a screwdriver and use it as a lever, but this is a last resort and requires skill.
Installing a new filter and assembling the system
After dismantling the old element, it is necessary to thoroughly clean the seat on the engine from remnants of the old gasket and dirt. Use a cloth soaked in solvent to keep the surface perfectly clean. This is critical to ensuring sealing and preventing oil leaks after the engine is started.
Apply a thin layer of clean engine oil to the rubber O-ring of the new filter. This will ensure easy screwing and prevent thread scuffing when tightening. Install the new filter by hand by rotating it clockwise until the sealing gasket touches the engine surface.
Next, you need to tighten the filter to the required tightening torque. Typically, manufacturers recommend tightening the filter 3/4 of a turn after touching the gasket, but it is better to refer to the instructions for the specific product. Do not use wrenches to tighten unless required, as excessive force may damage the threads or distort the housing.
Before installing a new filter, be sure to check that the old O-ring is not left on the engine block. A double ring will lead to an immediate oil leak after starting the engine.
Checking the oil level and checking for leaks
After installing a new filter, it is necessary to fill the engine with fresh engine oil to the required level. Use the dipstick to check the level, which should be between the MIN and MAX marks. Add oil gradually, checking the level every 500 ml to avoid overfilling.
Screw on the filler cap and start the engine. Let it idle for a few minutes. At this moment, the oil pressure indicator on the dashboard should light up and go out. Carefully inspect the filter installation location and the drain plug for leaks.
If you notice even the slightest traces of oil, turn off the engine immediately and eliminate the cause. Most often this is due to insufficient tightening of the filter or the presence of an old gasket in the seat. After checking, allow the engine to cool and check the oil level again, as some of the fluid will fill the new filter.
⚠️ Attention: Never start the engine without first checking the tightness of the drain plug and filter. This can lead to the loss of all oil volume and serious engine damage within a few seconds.
- Every maintenance (every 10-15 thousand km)
- More often than once every 15 thousand km
- Less than once every 15 thousand km
- Only for major repairs
Typical errors and operating tips
Many car owners make the mistake of installing a filter without first lubricating the O-ring. This leads to the rubber drying out, deforming and losing its seal when the engine is first started. Also common is the problem of the filter twisting when the owner tries to tighten it “all the way” with a wrench, which often ends with the thread breaking.
Another common mistake is using low-quality oil or not observing replacement intervals. For Nissan Qashqai with turbo engines, the oil change interval is often reduced to 7-8 thousand kilometers, since the turbine creates high temperatures and accelerates the aging of the lubricant. Ignoring this fact leads to coking of the channels and failure of the oil pump.
- 🚫 Do not skimp on the quality of the filter, as cheap analogues often have low cleaning efficiency.
- 🔧 Use only original or certified analogues recommended by the manufacturer.
- 📅 Keep an oil and filter change log to track the real condition of the engine.
| Parameter | Value for Nissan Qashqai (MR20DE) | Recommendation |
|---|---|---|
| Oil volume (with filter) | 4.8 - 5.1 liters | Pour 4.5 l, top up according to the level |
| Oil type | 5W-30, 5W-40 | Synthetics, standard RN0700 |
| Filter tightening torque | 15-20 Nm | Hand tighten + 3/4 turn |
| Plug tightening torque | 25-30 Nm | Replace copper washer |
Features of service for different generations of Qashqai
Despite the external similarity, the design features of the engines may differ depending on the year of manufacture and generation of the car. On the first generation Nissan Qashqai (J10) The filter is often located closer to the front of the engine compartment, making it easier to access. On the second generation (J11) and updated versions, the layout may be changed, and access to the filter is sometimes difficult due to protective elements.
It is important to consider that on diesel versions with an engine M9R The filtration system has additional features, including the presence of a water separator. In such cases, the replacement procedure may require additional steps to bleed the system or reset errors through a diagnostic scanner.
⚠️ Attention: On diesel engines with a diesel particulate filter (DPF), the use of low-quality oil or untimely replacement of the filter element can lead to costly repairs to the exhaust system.
The correct choice of oil and filter, as well as compliance with the replacement schedule, are the foundation for long-term operation of the Nissan Qashqai engine without serious breakdowns.
Conclusion and recommendations for further maintenance
Replacing the oil filter is a basic procedure that every owner should perform Nissan Qashqai. Regular performance of these works allows you to maintain the engine in good condition, ensuring its reliable operation for many years. Do not neglect the manufacturer's recommendations and use only high-quality consumables.
Remember that saving on a filter can result in much greater costs in the future. If you are not confident in your abilities or you do not have the necessary tools, it is better to entrust this work to professionals in the service center. However, by following our instructions, you can make a quality replacement yourself.
Timely replacement of the filter on a Nissan Qashqai extends the life of the turbine and piston group by 30-40% compared to operation without replacement.Frequently Asked Questions
Is it possible to replace the oil filter without draining the oil?
No, this is technically impossible. To replace the filter, it is necessary to drain the used oil, since the filter is located at the bottom of the engine and is under oil pressure.
How often do you need to change the oil filter on a Nissan Qashqai?
It is recommended to change the oil filter every time you change the engine oil, that is, every 10-15 thousand kilometers or once a year, depending on operating conditions.
What to do if the filter is twisted too much?
If the filter is too tight, use a special puller to unscrew it. Do not try to unscrew it with a wrench or pliers to avoid damaging the filter housing and motor threads.
Do I need to change the drain plug gasket when replacing the filter?
Yes, it is recommended to replace the copper or aluminum drain plug washer every time you change the oil and filter. This ensures the connection is tight and prevents leaks.
Can I use a filter from a manufacturer other than the original one?
Yes, you can use high-quality analogues from well-known brands such as Mahle, Mann, Ufi or Bosch. The main thing is that the filter matches the engine parameters and has suitable filtration characteristics.