Nissan Qashqai J11 is one of the most popular crossovers in Russia, and many owners sooner or later face the need to replace rims. Whether it’s tuning, a seasonal change of tires or a banal replacement of a damaged disc - without knowing the exact parameters bolt patterns can't get by. An error in selection can lead to vibrations, accelerated wear of wheel bearings, or even an emergency.

In this article we will analyze in detail all the disk parameters for Qashqai J11 (years 2014–2021), including PCD (bolt pattern), departure (ET), central hole diameter (DIA), as well as compatibility with other models Nissan And Renault. In addition, you will find practical advice on selecting disks, a table of original sizes and answers to frequently asked questions.

What is a bolt pattern and why is it important for the Nissan Qashqai J11

Term bolt pattern (or PCD - Pitch Circle Diameter) indicates the diameter of the circle on which the disc mounting holes are located. For Nissan Qashqai J11 this parameter is strictly fixed and amounts to 5×114.3 mm - five holes located on a circle with a diameter of 114.3 mm. A deviation from this value even by a fraction of a millimeter will lead to the fact that the disk will not fit tightly on the hub, and the fastening will be uneven.

Besides PCD, when selecting disks, you must consider:

  • 🔧 Departure (ET) — the distance from the mating plane of the disk to its central axis. For Qashqai J11 permissible range: from ET35 to ET45.
  • 🕳️ Central hole diameter (DIA) - must be at least 66.1 mm, but can be more (spacer rings are used).
  • 📏 Disc width and diameter - depend on the modification and year of manufacture (more details in the table below).

Ignoring these parameters is fraught with:

  • ⚠️ Vibration at speeds over 80 km/h (due to imbalance).
  • ⚠️ Accelerated wear wheel bearings and tires.
  • ⚠️ Refusal to undergo maintenanceif the drives do not meet factory specifications.
📊 How often do you change wheels on your Qashqai?
  • Every season (winter/summer)
  • Once every 2-3 years
  • Only if damaged
  • Never changed

Original wheel parameters for Nissan Qashqai J11 (table)

Factory parameters of disks depend on the configuration and year of manufacture Qashqai J11. Below is a table with original sizes for the most common versions:

Equipment / Engine Disc Diameter (inches) Rim Width (inches) Departure (ET) PCD (bolt pattern) DIA (mm)
1.2 DIG-T (115 hp), Visia / Acenta 16 6.5J 40 5×114.3 66.1
1.6 dCi (130 hp), N-Connecta 17 7.0J 40 5×114.3 66.1
2.0 dCi (177 hp), Tekna 18 7.5J 38 5×114.3 66.1
1.3 DIG-T (140/160 hp), restyling 2017+ 17–19 7.0J–8.0J 35–40 5×114.3 66.1

Please note: for restyled versions (from 2017), it is possible to install disks with a diameter of 19", but only with low-profile tires (for example, 225/45 R19). At the same time departure must be at least ET35, otherwise the disc will touch the suspension elements.

💡

If you plan to install larger diameter wheels (for example, 18" instead of 17"), be sure to check the ground clearance using suspension test: Load the vehicle and spin the wheels by hand to ensure there is no contact with the arch or shock absorber.

Wheel compatibility with other Nissan and Renault models

Thanks to the unification of the platform CMF-C/D, disks from Nissan Qashqai J11 suitable for a number of other models Nissan And Renault. However, there are nuances:

  • 🚗 Nissan X-Trail T32 (2014–2021) - full software compatibility PCD 5×114.3 And DIA 66.1, but the offset may vary (ET35–45 for X-Trail against ET38–40 for Qashqai).
  • 🚗 Renault Kadjar (2015–2022) - identical parameters, but original wheels Kadjar often have overshoot ET42.
  • 🚗 Renault Koleos II (2016–2023) - same PCD, but the diameter of the central hole can be 66.1 mm or 71.1 mm (adapter rings required).
  • ❌ Nissan Juke F15/F16 - despite the external similarity, looseness 4×100, which makes the disks incompatible.
⚠️ Attention: When installing discs from Renault Kadjar or X-Trail on Qashqai J11 be sure to check departure (ET). A difference of 2–3 mm can lead to a shift in the track and poor handling.

If you are considering drives from other models, use the following checklist:

☑️ Checking disk compatibility

Done: 0 / 5

How to choose the right wheels for the Qashqai J11: step-by-step instructions

Selecting drives is a responsible process, especially if you plan to deviate from the factory settings. Follow this algorithm:

  1. Define your goal:
    • 🔄 Seasonal replacement (steel wheels for winter, cast wheels for summer).
    • 🚀 Tuning (increasing diameter, changing design).
    • 🔧 Replacement of a damaged disk (selection according to original parameters).
  2. Check the parameters:
    • 📋 PCD 5×114.3 - no options.
    • 📋 DIA 66.1 mm (or more with adapter rings).
    • 📋 Departure ET35–ET45 (for 18–19" disks it is better to stick to ET38–40).
  3. Consider the width and diameter:
    • 📏 For 16" - width 6.5J–7.0J.
    • 📏 For 17" - width 7.0J–7.5J.
    • 📏 For 18"–19" - width 7.5J–8.0J (requires low profile tires).
  4. Check tire compatibility:
    • 🔍 Use a tire size calculator (for example, WillTheyFit) to avoid conflicts with arches.
    • ⚠️ For disks 19" minimum tire profile height - 45% (For example, 225/45 R19).

If you are in doubt about your choice, contact VIN code your car. Disk parameters can be specified:

  • 📄 In the service book (section "Wheels and Tires").
  • 🖥️ On the website Nissan Russia (enter VIN in the Technical Information section).
  • 🔧 From an official dealer (free on request).
What happens if you install wheels with the wrong offset?

A misaligned track will lead to uneven tire wear and increased load on the wheel bearings. When ET < 35 the disc may touch the brake caliper, when ET > 45 — move inside the arch, which impairs handling at high speeds.

Top 5 mistakes when choosing wheels for Qashqai J11

Even experienced car owners sometimes make mistakes that lead to additional expenses or safety problems. Here are the most common:

  1. Ignoring crash (ET)

    Many people think that if PCD matches, then the disk will fit. However, departure ET critical: a deviation of ±5 mm is already considered dangerous. For example, a disk with ET30 (instead of ET40) will move the wheel outward, which will increase the load on the hub.

  2. Buying discs without taking into account the central hole (DIA)

    If DIA disk larger than 66.1 mm, you will need centering rings. Without them, the disc will not be firmly fixed to the hub, which will lead to the steering wheel wobbling.

  3. Installing rims that are too wide without checking the clearance

    Rims width 8.5J or more may affect shock absorbers or springs, especially when the car is fully loaded. Always test on suspension!

  4. Saving on quality

    Cheap replicas of famous brands (for example, BBS or OZ Racing) often have imprecise geometry, which leads to imbalance and vibration.

  5. Failure to comply with seasonal recommendations

    For winter tires it is better to use steel wheels (they are cheaper and more resistant to corrosion from reagents), and for summer tires - lightweight cast or forged ones.

⚠️ Attention: If you are installing disks with ET < 38 for version with engine 2.0 dCi, there is a high probability of contact with the brake calipers (due to the large brake mechanisms in top trim levels).

Recommendations for disc brands and materials

Not only appearance, but also safety depends on the material and manufacturer of the discs. Let's look at the main options:

1. Steel wheels

✅ Pros: cheap, durable, corrosion resistant (if properly coated), ideal for winter.

❌ Cons: heavy (impairs dynamics), limited design.

🔹 Recommended brands: KFZ, Steel Wheels, Nissan Original (article 40520-JM00A for 16").

2. Alloy wheels

✅ Pros: lightweight (improves acceleration and braking), wide selection of designs.

❌ Cons: fragile (can crack with a strong impact), more expensive than steel.

🔹 Recommended brands: BBS, OZ Racing, Enkei, Replica (budget option).

3. Forged wheels

✅ Pros: the most durable and lightest, suitable for aggressive driving.

❌ Cons: high price (from 30,000 ₽ per set).

🔹 Recommended brands: Forgiato, HRE, Vossen.

For Nissan Qashqai J11 the optimal price/quality ratio will be alloy wheels Replica or Dezent (Germany). If the budget is limited - steel wheels Nissan Original followed by painting.

💡

For the winter season, it is better to use steel discs with an anti-corrosion coating - they will last longer when in contact with salt and reagents.

FAQ: Frequently asked questions about Qashqai J11 bolt pattern

Is it possible to install 5x112 disks instead of 5x114.3?

No, that's impossible. The difference is PCD (112 mm vs 114.3 mm) will lead to the fact that only 2-3 bolts out of 5 will be tightened correctly, and the rest will be skewed. This is extremely dangerous and will lead to the wheel coming off while driving.

What wheels are suitable for Renault Megane 4?

Renault Megane 4 has a bolt pattern 5×114.3 And DIA 66.1 mm, but it crashes most often ET45–ET50. Such disks can be installed on Qashqai J11, but the track will widen, which will worsen handling. It is recommended to use spacers to adjust the offset.

Is it possible to install 19" wheels on a pre-restyling Qashqai J11 (2014–2016)?

Technically yes, but only if:

  • Using low profile rubber (for example, 225/40 R19).
  • Checking the ground clearance (the disc should not touch the shock absorber when the steering wheel is turned completely).
  • Departure no less ET38.

Otherwise, there may be problems with maintenance and increased wear of the suspension.

What to do if the disc does not fit on the hub due to a large DIA?

Use centering rings (adapters). They make up the difference between DIA disk and hub. For example, if DIA disc is 71.1 mm, and the hub is 66.1 mm, you need a ring with an outer diameter of 71.1 mm and an inner diameter of 66.1 mm. Cost - from 500 ₽ per set.

How to check the authenticity of BBS or OZ Racing wheels?

Original discs have:

  • Engraved brand logo (not a sticker!).
  • Serial number on the inside.
  • Certificate of conformity (from official dealers).

Counterfeits are often 10–15% lighter and have rough edges.