Lamps in Nissan Almera G15: what they cost, how to change and what to replace with

Nissan Almera G15 (2013–2022) is one of the most popular sedans in Russia, but even in such a reliable car the lamps burn out over time. The head light dims, the side lights fail, and the rear brake light flashes like a Christmas garland - is this a familiar picture? In this article we will analyze all types of lamps in Almera G15, from low beam to glove compartment lighting, and we’ll also show you how to replace them without calling service.

Many owners are faced with a problem: the store offers dozens of lamp options, but which ones are right for your car? We have collected current data on sockets, power and brands, which are guaranteed not to blind oncoming drivers and not burn wiring. And we’ll also reveal the secret of factory marking of lamps on Almera G15, which you will not find in standard catalogs.

What kind of lamps are installed in the Nissan Almera G15 from the factory?

From the assembly line Nissan Almera G15 complete with lamps standard power, complying with European safety standards. However, after 2–3 years of operation, their brightness drops by 30–40%, and their service life is reduced due to vibrations and voltage surges. Below is the complete list original lamps by position:

• 💡 Low/high beam: halogen H4 (12V, 60/55W) - double-filament, with P43t base.
• 🚦 Front turn signal: baseless lamp PY21W (12V, 21W, orange bulb).
• 🔆 Side lights (front): W5W (12V, 5W) - miniature lamps with W2.1×9.5d socket.
• 🛑 Rear brake light/marker: two-pin lamp P21/5W (21W stop, 5W clearance).
• ⚡ Fog lights (PTF): H11 (12V, 55W) - only in trim levels with PTF.
• 🔦 License plate light: C5W (12V, 5W) - soffit lamp with SV8.5 base.

Important: in restyled versions Almera G15 (from 2019) can be used in rear lights LED modules instead of incandescent lamps. You can check this by the markings on the lampshade - if there is an inscription LED>, there is no need to change the lamps.

Types of lamps to replace: what to choose instead of standard ones

Factory halogen lamps Almera G15 They last on average 2–3 years, but they can be replaced with more durable and brighter analogues. Let's consider all available options with pros and cons:

⚠️ Attention: Installation LED lamps in halogen optics Without a light beam corrector, it can lead to blinding oncoming drivers. In the Russian Federation Traffic Regulations (clause 3.6) this is regarded as a violation, the fine is 500 ₽.

For Almera G15 the best option in terms of price/quality ratio - premium halogen lamps (For example, Osram Night Breaker or Philips X-tremeVision). They provide 130% more light than stock and last longer due to vibration resistance.

Step-by-step replacement of lamps in the Almera G15 headlight

Replace the low/high beam bulbs in Nissan Almera G15 you can do it yourself in 15–20 minutes. The main thing is not to touch the bulb of a halogen lamp with bare hands: traces of grease lead to overheating and rapid failure. You will need:

• 🔧 Flathead screwdriver (for removing clips)
• 🧤 Cotton gloves or napkin
• 💡 New lamp H4 (or H11 for PTF)
• 🔦 Flashlight (for convenience)

Instructions for replacing the low/high beam lamp:

1. Open the hood and remove protective cover headlights (turn counterclockwise).
2. Disconnect power connector from the lamp by pressing the latch.
3. Remove spring retainerholding the lamp (pull up).
4. Carefully remove the old lamp and install the new one, without touching the flask.
5. Secure the clamp, connect the connector and check the operation of the light.

Turn off the ignition and let the headlights cool|Check the integrity of the new lamp (for cracks in the bulb)|Make sure that the base matches the original (H4 for near/far)|Prepare tools: screwdriver, gloves, flashlight-->

⚠️ Attention: If the lamp does not light after replacement, check fuse F35 (10A) in the block under the steering wheel. He is responsible for the right headlight, and F36 - for the left. A blown fuse can only be replaced with one of the same rating!

Tail lights: how to change the brake light and tail light

In the taillights Almera G15 a combination lamp is used P21/5W, where one thread is responsible for the brake light (21W), and the second for the clearance (5W). Replacement takes 5 minutes and requires no tools:

1. Open the trunk and remove plastic cover on the inside of the lantern (it is held on by latches).
2. Turn the lamp socket counterclockwise and pull it out.
3. Press the lamp, turn it counterclockwise and remove it.
4. Install a new lamp P21/5W, observing the position of the contacts (the protrusion on the base must coincide with the groove in the cartridge).

🔹 Important nuance: If after replacement the brake light does not work, but the indicator light is on, it means that only one filament has burned out. In this case, the lamp still needs to be replaced - Driving with a faulty brake light is fined 500 RUB (Article 12.20 of the Code of Administrative Offenses of the Russian Federation).

For rear PTF (if they are included) lamps are used P21W (21W). Their replacement is similar, but the socket is located below the main flashlight.

Interior lamps and lighting: glove compartment, courtesy light, dashboard

Inside Almera G15 Several types of lamps are used, and replacing them often raises questions. Let's look at the most problematic areas:

• 📄 Glove compartment lighting: lamp C10W (12V, 10W) with base SV8.5. To replace, open the glove compartment, remove the plastic trim on the right and unscrew the cartridge counterclockwise.
• 🚗 Interior lighting: lamp DE3175 (12V, 10W) - baseless, with two contacts. The cartridge is removed by turning it 90°.
• 📉 Dashboard lighting: LED elements (not replaced separately, only the entire unit). If the backlight dims, check fuse F20 (7.5A).
• 🔑 Ignition switch illumination: lamp T4W (12V, 4W). To replace, you need to remove the lower steering column pad.

💡 Advice: If you want to make the interior brighter, replace the standard incandescent lamps with LED analogues with plinth T10 (for the lampshade) or BA9s (for the glove compartment). They consume 5 times less energy and do not heat up.

Common mistakes when replacing lamps and how to avoid them

Even experienced drivers sometimes make mistakes that lead to rapid failure of lamps or even short circuit. Here are the most common:

1. Touching the bulb of a halogen lamp bare hands. Oil from the fingers creates local overheating, and the lamp burns out after a few days. Solution: use gloves or wipe the flask with alcohol.
2. Installation of high power lamps (For example, H4 100/90W instead of 60/55W). This leads to melting of the wiring and the cartridge. Solution: Stick to standard settings.
3. Ignoring polarity when connecting LED lamps. They won't work or will burn out quickly. Solution: check the markings + And – on the plinth.
4. Replacing just one lamp in the headlight. Different color temperatures (for example, 4300K ​​and 6000K) reduce visibility. Solution: Change lamps in pairs.

⚠️ Attention: If, after replacing the lamps, the headlight appears condensate, this is a sign of depressurization. Do not ignore the problem - moisture leads to corrosion of the reflector and failure of the headlight. Solution: remove the headlight, dry it with a hairdryer (temperature no higher than 60°C) and apply sealant to the joints.

Top 5 lamp manufacturers for Nissan Almera G15

Not only brightness depends on the brand of lamps, but also resource, vibration resistance And light beam matching GOST requirements. We tested 12 manufacturers and selected the best:

For fog lights (H11) the best choice is Osram Fog Breaker (luminous flux 1350 lm) or Philips WhiteVision (white-blue light 4200K). These models provide maximum visibility in fog and rain.

FAQ: Frequently asked questions about lamps in Nissan Almera G15