Cabin filter in Nissan Murano Z52 - this is not just a consumable, but a key element that affects the quality of air in the cabin, the operation of the climate control system and even the health of the driver and passengers. Over time, the filter becomes clogged with dust, pollen, bacteria and small particles, which leads to reduced ventilation efficiency, the appearance of unpleasant odors and increased load on the air conditioning system. If you notice that the air in the cabin has become less fresh and the airflow is weaker, it’s time to think about replacing it.

In this article we will look in detail at how to replace the cabin filter yourself with Murano Z52 (restyling and pre-restyling) without resorting to service. You will learn where the filter is located, what tools you will need, how to choose a high-quality analogue of the original filter and avoid common mistakes. The instructions are suitable for petrol and diesel versions, as well as for models with all-wheel drive and front-wheel drive. Let's get started!

Where is the cabin air filter located in the Nissan Murano Z52?

B Nissan Murano Z52 The cabin filter is located behind the glove compartment on the passenger side. This is a typical location for most crossovers Nissan, but access to it may vary depending on the year of manufacture and configuration. In pre-restyling versions (2007–2010), the filter is hidden behind a plastic cover, and in restyled versions (2011–2014) - behind an additional panel.

To get to the filter you will need:

  • 🔧 Open the glove compartment and lower it completely (in some versions you need to press the latches on the sides).
  • 🔍 Behind the glove compartment you will see a plastic cover with latches or screws (depending on the modification).
  • 📍 The filter is located in a vertical housing that is attached to the ventilation system.

It is important to consider that in some trim levels Murano Z52 can be installed double filter (coal + dust) or a combined option. If you are unsure of the filter type, check it visually before purchasing a new one.

📊 How often do you change the cabin filter?
  • Every 10,000 km
  • Once a year
  • Only when the smell appears
  • Never changed

What tools are needed for replacement?

To replace the cabin filter with Nissan Murano Z52 no complex equipment required. In most cases, the minimum set is sufficient:

  • 🔨 Screwdriver with a Phillips head (for the cover mounting screws, if any).
  • 🔧 Plastic puller or flat screwdriver (for carefully removing latches).
  • 🧹 Vacuum cleaner or brush (to clean the filter housing from dust and debris).
  • 📸 Phone with a flashlight (to illuminate hard-to-reach places).
  • 🛠️ New cabin filter (original or high-quality analogue).

If in your modification Murano Z52 The filter is attached with latches; a screwdriver may not be needed. However, in restyled versions (2011–2014), self-tapping screws are sometimes found, so it is better to prepare in advance.

⚠️ Attention: Do not use metal tools to remove plastic latches as this may cause the fasteners to break. The best option is a plastic puller or a screwdriver wrapped in electrical tape.
💡

Before replacing the filter, turn on the stove at maximum power for 1-2 minutes. This will help blow some of the debris out of the vent system and make cleaning easier.

Which cabin filter to choose for Murano Z52?

There are many options for cabin filters on the market. Nissan Murano Z52, but not all of them are equally effective. Original filter from Nissan has an article number 27277-4M000 (dust) or 27277-4M001 (coal). However, it can be replaced with high-quality analogues from trusted brands.

Here is a comparison table of popular filters:

Brand Article Type Price (approximate) Features
Nissan (original) 27277-4M000 Dusty 1 200–1 500 ₽ Guaranteed compatibility, high quality materials
Mann Filter CU 29003 Coal 800–1 000 ₽ Good filtration, affordable price
Bosch 1 987 429 636 Dust/coal 700–900 ₽ Universal option, suitable for most modifications
Filtron K 1354 Coal 600–800 ₽ Budget option with good reviews
TSN 9.7.864 Dusty 400–600 ₽ The cheapest analogue, but the filtration quality is lower

When choosing a filter, pay attention to its type:

  • 🌿 Dust filter - traps dust, pollen, soot, but does not cope with odors and harmful gases.
  • ⚫ Carbon filter — additionally absorbs unpleasant odors and toxic substances (for example, exhaust gases).
  • 🔄 Combination filter - combines both types, but costs more.

For Murano Z52 the optimal choice would be carbon filter, especially if you often drive in the city or on dusty roads. It copes better with dirt and keeps the air in the cabin fresher longer.

Step-by-step instructions for replacing the cabin filter

Now let's move on to the replacement process itself. Follow the instructions carefully to avoid mistakes.

Stop the car on a level surface and turn off the engine|

Open the glove compartment and empty it of its contents|

Prepare your tools and new filter|

Turn on the flashlight on your phone for illumination -->

Step 1: Access the filter

Open the glove compartment and press the side releases (if equipped) to lower it completely. In some versions Murano Z52 The glove compartment is hinged - in this case, just pull it towards you.

Step 2: Removing the Cover

Behind the glove compartment you will see a plastic cover. It can be attached:

  • 🔄 On the latches (carefully pry them off with a flat screwdriver or puller).
  • 🔩 On self-tapping screws (unscrew them with a Phillips screwdriver).

Be careful - the plastic is fragile, and if you press hard, the latches may break.

Step 3: Removing the old filter

After removing the cover you will see the filter housing. Pull it towards you and it should come out without effort. If the filter is stuck, check for additional latches on the sides.

⚠️ Attention: When removing the filter from the housing, a large amount of debris may spill out. Lay down newspaper or use a vacuum cleaner in advance to avoid getting the interior dirty.

Step 4: Clean the Case

Before installing a new filter, clean the housing from dust and dirt. You can use a vacuum cleaner or brush. If moisture or mold has accumulated inside, wipe the surface with a damp cloth and let dry.

Step 5: Install a new filter

Insert the new filter into the housing, observing the direction of air flow (usually indicated by the arrow on the filter). Make sure the filter is seated tightly and is not loose.

Step 6. Assembly

Close the lid (snap or tighten the screws) and return the glove compartment to its place. Check that all latches are latched.

Step 7: Check

Start the car, turn on the airflow to maximum power and check for any unusual noises or odors. If the air is blowing weakly, the filter may not be installed correctly or the housing may not be closed tightly.

💡

If after replacing the filter there is still an unpleasant odor in the cabin, the cause may be mold in the ventilation system. In this case, it is recommended to treat it with a special antibacterial spray.

Typical mistakes when replacing the cabin filter

Even such a simple procedure as replacing the cabin filter may not go according to plan if some nuances are not taken into account. Here are the most common mistakes and how to avoid them:

  • 🔄 Incorrect filter direction. The filter housing usually has an arrow indicating the direction of air flow (top to bottom or bottom to top). If you install the filter backwards, it will perform worse at filtration, and debris may get into the ventilation system.
  • 🔩 Damage to the lid latches. Many owners Murano Z52 they break the plastic clips trying to remove the cover by force. Use a plastic puller or a cloth-wrapped screwdriver.
  • 🧹 Ignoring case cleaning. If you do not remove dust and debris from the housing before installing a new filter, it will clog much faster. Always clean the housing with a vacuum cleaner or brush.
  • 📏 Buying the wrong size filter. Even if the article number is correct, sometimes filters from different manufacturers may differ in size. Before purchasing, check the dimensions with the old filter.
  • 🚗 They forget to check the operation of the system after replacement. Always turn on the airflow at full power to make sure the filter is installed correctly and there are no air leaks.

Pay special attention to filters with a carbon layer - they must be hermetically sealed. If the packaging is damaged, the charcoal may have absorbed moisture and lost its properties.

How often should you change the cabin filter?

Recommended cabin filter replacement interval for Nissan Murano Z52 — every 15,000 km or once a year. However, this period may vary depending on operating conditions:

  • 🏙️ City driving. If you often sit in traffic jams, the filter will clog faster due to the high concentration of exhaust gases and dust. Change every 10,000 km.
  • 🌳 Country trips on dirt roads. Dust and sand quickly clog the filter - check its condition every 8,000–10,000 km.
  • 🌧️ Humid climate. In high humidity conditions, mold may develop on the filter. Change it at least once a year, even if the mileage is low.
  • 🚗 Intensive use. If you drive more than 30,000 km per year, reduce the replacement interval to 10,000–12,000 km.

There are several signs that it is time to change the filter ahead of schedule:

  • 👃 The appearance of an unpleasant odor in the cabin (especially when the airflow is turned on).
  • 💨 Weak air flow from the deflectors when the ventilation is turned on.
  • 🤧 Increased amount of dust on the dashboard, even after cleaning.
  • 🌫️ Fogging of windows in wet weather (may indicate poor air circulation).

If you notice any of these signs, don't delay replacement - a dirty filter not only reduces comfort, but also increases the load on the climate control system, which can lead to its failure.

Video instructions for replacing the cabin filter on a Murano Z52

For clarity, we recommend watching the video instructions. Below is one of the best videos that shows in detail the replacement process for Nissan Murano Z52 (restyling 2012). Pay attention to the nuances of removing the cover and installing the filter:

Video: Replacing the cabin filter Nissan Murano Z52 (2011–2014)

Description: The author shows how to get to the filter, what tools to use, and what to pay attention to when installing a new filter. Duration: 8 minutes.

What to do if the filter cannot be removed?

If the filter is stuck to the housing and does not come out, do not pull it by force - this may damage the plastic guides. Try gently prying it from the sides with a flat-head screwdriver or rocking it from side to side. In extreme cases, silicone lubricant can be used to make removal easier.

If you have a different modification Murano Z52 (for example, pre-restyling 2008), look for a video specifically for your year of manufacture - the location of the filter and the method of attaching the cover may differ slightly.

FAQ: Frequently asked questions about replacing the cabin air filter on a Murano Z52

Is it possible to drive without a cabin filter?

Technically yes, but it is highly undesirable. Without a filter, dust, pollen, insects and even small stones from the road will enter the cabin. In addition, the ventilation system will become clogged with debris, which will lead to its breakdown. In the long run, this will cost more than buying a new filter.

What is the difference between a carbon filter and a regular one?

The carbon filter, in addition to mechanical dust removal, contains a layer of activated carbon that absorbs harmful gases (for example, exhaust) and unpleasant odors. A conventional (dust) filter cannot cope with this task. For urban use, a carbon filter is preferable.

Which filter is better - original or analogue?

Original filter from Nissan It is guaranteed to fit in size and be of high quality, but it costs more. Analogues from Mann Filter, Bosch or Filtron often not inferior in efficiency, but cheaper. The main thing is to buy filters from trusted sellers to avoid counterfeits.

Do the seals need to be lubricated when replacing the filter?

No, this is not necessary. Filter and housing seals are usually made of rubber or soft plastic and do not require lubrication. However, if you notice that they are dry or cracked, you can gently treat them with silicone lubricant to extend their life.

Is it possible to wash the cabin filter instead of replacing it?

Theoretically, you can wash the dust filter with water and dry it, but this is a temporary solution. It is useless to wash the carbon filter - carbon loses its properties when wet. After washing, the filter will still have to be replaced in the near future, as its efficiency will decrease.