Owners Nissan Qashqai J10 after restyling 2010–2013, sooner or later they are faced with the need to replace lamps - be it a burnt-out headlight, a dim brake light, or a failed marker. But how to understand the variety of types of socles, choose a high-quality analogue and not run into a fake? This article will help you avoid common mistakes when choosing and replacing lamps in First generation Qashqai after the update, and will also talk about nuances that are not covered even in official manuals.

We will analyze in detail all light elements — from the head light to the interior lighting, we will indicate the original articles Nissan and proven analogues from Osram, Philips And Koito. Let us separately dwell on the “pitfalls”: why LED lamps in foglights can blind oncoming people, how to distinguish a high-quality halogen lamp from a cheap fake, and what to do if the low beam lamp blinks after replacement. And for those who prefer to do everything themselves, we will provide step-by-step instructions with photos and videos.

Types of lamps in Nissan Qashqai J10 restyling: complete list with sockets

B Qashqai J10 after restyling in 2010, lamps of three main categories are used: halogen (in basic configurations), xenon (in top versions with the system AFS) and LED (only in interior lighting and dimensions of some modifications). Below is a complete table indicating the bases and number of lamps for each zone.

Lighting area Lamp type / Base Quantity (pcs.) Notes
Low beam H7 (halogen) / D1S (xenon) 2 Xenon versions require an ignition unit
High beam H1 2 In some trim levels it is combined with low beam (bi-xenon)
Fog lights (PTF) H11 2 Replacement with LED with light beam corrector is allowed
Side lights (front) W5W (baseless) 4 Restyled versions may have LEDs
Tail lights (stop/side) P21/5W (double strand) 4 The brake light filament often burns out

It is important to consider that in Qashqai J10 after restyling in 2010, changes occurred in the headlights: for example, in some trim levels they appeared LED dimensions, and in versions with xenon - automatic headlight range adjustment (AFS). This means that when replacing lamps you may need to error reset via a diagnostic scanner (for example, ELM327) if the system recognizes the new lamp as faulty.

It is also worth noting that in European And Russian versions Qashqai J10 lamp types may differ for turn signals: some cars have PY21W (orange glass), and in others - baseless WY5W with yellow coating. Before purchasing, be sure to check visually or by VIN-code.

📊 What lamps did you change in your Qashqai J10?
  • Low beam
  • High beam
  • Fog lights
  • Tail lights
  • Interior lighting

Original articles and the best analogues: what to choose?

Original lamps Nissan for Qashqai J10 supplied by the company Koito (Japan), but their price is often 2–3 times higher than their analogues. Below are proven options for key lighting areas, including SKUs and average prices for 2026.

  • 🔦 Low beam (H7): original 26510-4M000 (~1200 rub.), analogues - Osram Night Breaker Laser (64210NBL, ~800 rub.), Philips X-tremeVision +130% (12972XV2, ~950 rub.).
  • 💡 High beam (H1): original 26510-4M010 (~1000 rub.), analogues - Narva Range Power (48311, ~500 rub.), Bosch Pure Light (1987302071, ~600 rub.).
  • 🌫️ Fog lights (H11): original 26510-4M020 (~1500 rub.), analogues - Osram Fog Breaker (64211FB, ~700 rub.), Philips WhiteVision (12362WV1, ~1100 rub.).
  • ⚠️ Tail lights (P21/5W): original 26550-4M000 (~800 rub.), analogues - GE Megalight Ultra (56151, ~400 rub.), MTF Light Argentum (P215W, ~300 rub.).

Critical nuance: in xenon versions of the Qashqai J10, the restyled D1S lamps must be strictly original (article number 26510-4M030) or certified analogues from Philips or Osram. Cheap Chinese xenon lamps often cause an error B2600 (malfunction of the lighting system) and can damage the ignition unit.

When choosing LED lamps for fog lights or dimensions, pay attention to certification ECE R11 (for PTF) or ECE R6 (for dimensions). Uncertified LEDs can blind oncoming drivers and cause a fine. Among proven brands - Hella, MTF Light And Morimoto.

💡

Before purchasing lamps, check their authenticity: they are original Osram And Philips there is a hologram on the packaging, and on the base there is a laser-engraved brand logo.

Step-by-step replacement of low and high beam lamps

Replacing lamps in a headlight Qashqai J10 restyling does not require special tools, but there are several key points, which will simplify the process:

  1. Disconnect the negative terminal of the battery (to avoid short circuit).
  2. Remove the protective rubber boot from the back of the headlight unit by pulling it towards you.
  3. Disconnect the power supply from the lamp by pressing the latch.
  4. Remove the lamp from the grooves by turning it counterclockwise (for H7) or by pulling towards you (for H1).
  5. Install a new lamp, without touching the flask with your hands (fat traces reduce service life).

For lamps low beam (H7) It is important to orient the base correctly: the protrusion on the lamp must coincide with the groove in the headlight. If the lamp does not lock, check whether you have mixed up the sides (the left/right headlight has a mirror arrangement of the grooves).

☑️ What to check before replacing a low beam lamp

Done: 0 / 5

When replacing high beam (H1) Be careful: the bulb of this lamp is thinner than that of H7, and it is easy to damage. Also in some trim levels Qashqai J10 To access the lamp you need to remove the air filter (on the right side).

⚠️ Attention: If, after replacing the low beam lamp, it blinks or is lit at full intensity, check the contacts in the power supply. Often the problem lies in oxidized or burnt contacts, and not in the lamp itself. Clean them with alcohol or a special spray (for example, Kontakt 60).

Fog lights: replacement and upgrade to LED

Lamps H11 in foglights Qashqai J10 They are easier to change than in a block headlight, but there are some nuances here. For example, if you decide to install LED lamps, please note that:

  • 🔧 Most LED modules require polarity reversal (swap “+” and “–”), since in Nissan polarity is non-standard.
  • 📏 The LED light beam must be adjusted (many models shine too high, blinding oncoming people).
  • ⚡ Cheap LED lamps often lack current stabilization driver, which leads to flickering.

To replace the lamp H11 in PTF:

  1. Unscrew the plastic nut (or two screws, depending on the year of manufacture) from the inside of the bumper.
  2. Pull the headlight towards you and disconnect the power connector.
  3. Turn the lamp counterclockwise and remove it.
  4. Install the new lamp, making sure that the O-ring is not damaged.

If you choose LED upgrade, pay attention to models with a certificate ECE R11, for example:

  • Osram LEDriving FOG (64211CWX2) - optimal price/quality balance.
  • Philips UltinonEssential (12499ULX2) - good light temperature (6000K), but requires angle adjustment.
  • MTF Light P11-W - budget option with beam corrector.
⚠️ Attention: After installing LED lamps in fog lights Qashqai J10 an error light may appear on the dashboard (C1609 — PTF circuit malfunction). This is due to the fact that the on-board system recognizes that the LED resistance is too low. Solution - installation resistance trompe l'oeil (For example, Canbus- adapters).
How to check polarity in Qashqai J10 fog lights

Connect the tester in DC mode to the terminals of the block. If the voltage is positive, the polarity is standard. If it is negative, a polarity reversal is required (swap the wires on the LED lamp).

Tail lights: why P21/5W bulbs burn out and how to replace them

Lamps P21/5W in the rear lights Qashqai J10 - one of the weakest points. They burn out more often than others due to:

  • 🔥 Bad contact in the cartridge (oxidation or burning).
  • 💧 Moisture ingress inside the lantern (check the tightness of the seal).
  • ⚡ Power surges in the on-board network (especially important when installing additional equipment).

To replace the lamp P21/5W:

  1. Open the trunk and remove the plastic trim from the canopy side (it is secured with clips).
  2. Turn the cartridge counterclockwise and remove it.
  3. Press the lamp and rotate it counterclockwise, then pull it out.
  4. Install the new bulb, making sure that both threads (brake light and marker) are positioned correctly.

If the lamp burns out too often (once every 1–2 months), the problem may lie in voltage regulator relay (article 28470-3M600). Replacing it will cost ~1500 rubles, but will save you money on the constant purchase of lamps. It is also recommended to use lamps with reinforced glass, for example, Narva Long Life (48326).

💡

If, after replacing the P21/5W lamp, both modes (stop and parking) do not light up, check fuse F37 (10A) in the mounting block. He is responsible for the rear light circuit.

Interior and trunk lighting: W5W lamps and their analogues

B Qashqai J10 restyling, baseless lamps are used to illuminate the interior, trunk and glove compartment W5W (also known as T10). Replacing them takes less than a minute, but there are a few points:

  • 🔄 In the interior lampshade, the lamp is fixed by turning it counterclockwise.
  • 💡 In the trunk, the lamp simply pulls out of the socket (without turning).
  • 🔋 A lamp is used to illuminate the glove compartment in some trim levels C5W (article 26530-4M000).

When choosing analogues for W5W please note:

  • Osram Cool Blue (2825CBI) - cool white light (6000K), but weaker than standard in brightness.
  • Philips WhiteVision (12860WV1) - the best option for the salon (4200K).
  • LED lamps MTF Light (W5W-12SMD) - brighter than halogen, but may require polarity.

If after replacement the lamp in the interior light does not light, check door limit switch (contacts often oxidize). Also in Qashqai J10 there is a light switch delay relay (25230-3M600), which may fail.

Common mistakes when replacing lamps and how to avoid them

Even experienced car owners make mistakes when replacing bulbs. Qashqai J10. Here are the most common ones and ways to avoid them:

  1. Touching the bulb of a halogen lamp with your hands → use gloves or a cloth. Fatty traces lead to local overheating and shorten the life of the lamp.
  2. Installation of LED lamps without light beam corrector → choose models marked ECE and adjust the headlight angle.
  3. Ignoring errors on the dashboard after replacement → if it lights up Check Engine or light bulb icon, check the polarity and resistance of the circuit.
  4. Buying cheap xenon lamps → non-original xenon can damage the ignition unit (repair cost - from 10,000 rubles).
  5. Replacing a P21/5W lamp without checking the socket → oxidized contacts will lead to rapid burnout of the new lamp.

Another typical problem is condensation inside the headlight after replacing the lamp. This happens if it is damaged boot seal or if the lamp is not installed securely. Solution:

  • Check the integrity of the rubber seal (part number 26590-4M000).
  • After replacing the bulb, blow out the headlight with compressed air (such as a tire compressor).
  • If the condensation does not disappear, remove the headlight and dry it with a hairdryer (temperature no higher than 60°C).
💡

If after replacing the low beam lamp the headlight shines dimly, check the voltage at the contacts of the block. The norm is 12–14 V. If the voltage is below 11 V, the problem is in the wiring or generator.

FAQ: Frequently asked questions about lamps in Nissan Qashqai J10 restyling

Is it possible to install LED lamps in low beam instead of halogen ones?

Technically yes, but with caveats:

  • LED lamps H7 must have a certificate ECE R112.
  • The light beam will need to be adjusted (otherwise it will blind oncoming drivers).
  • Errors on the dashboard are possible (can be solved by installing Canbus- deception).

Best options: Osram LEDriving HL (64210CBI) or Philips UltinonPro6000 (12972ULX2).

What is the service life of the original H7 lamps in the Qashqai J10?

Average service life of original lamps Koito H7 — 500–700 hours (or 2–3 years with standard use). The resource is affected by:

  • On/off frequency (the more often, the faster the thread burns out).
  • Quality of voltage in the on-board network (surges shorten service life).
  • Temperature conditions (lamps last longer in cold weather than in hot weather).

Signs of imminent failure: flickering at startup, dimming of light, yellowing of the bulb.

Why did condensation appear in the headlight after replacing the lamp?

Condensation inside the headlight after replacing the lamp occurs due to:

  • Damaged o-ring anther
  • Loosely installed lamp (the seal is broken).
  • Cracks in the headlight housing (check near the fasteners).

Solution:

  1. Remove the headlight and dry it with a hairdryer (temperature up to 60°C).
  2. Check the seal (part no. 26590-4M000) and replace if necessary.
  3. Apply silicone sealant to the joints of the headlight housing.
Which bulbs are better for foglights: halogen or LED?

The choice depends on your priorities:

Criterion Halogen (H11) LED (H11)
Brightness 1200–1500 lm 2000–3000 lm
Service life 300–500 hours 30,000–50,000 hours
Cost 300–1000 rub. 2000–6000 rub.
Heating High (risk of headlight melting) Low

Recommendation: if you drive mostly around the city, a high-quality halogen is enough (Osram Night Breaker). For country trips and poor visibility, LED with a certificate is better ECE R11.

How to reset the lamp error after replacement?

If the fault icon on the instrument panel is illuminated after replacing the lamp, do the following:

  1. Check polarity (relevant for LED).
  2. Reset errors via diagnostic scanner (eg ELM327 with the program Torque).
  3. If the error persists, install decoy resistance (for LED) or check fuse (for halogen).

For xenon lamps (D1S) may be required flashing the ignition unit (contact service).