Lamps for Nissan Almera G15: types, characteristics and correct replacement

Nissan Almera G15 is a popular sedan that is valued for its reliability and ease of maintenance. However, even in such a machine, the lighting elements need to be replaced over time. Lamps in headlights, parking lights or brake lights burn out, dim or simply become obsolete (for example, when switching to LEDs). In this article we will look at what lamps are used in Almera G15 different years of manufacture, how to select them correctly and replace them without errors.

A special feature of the model is unified optics with other alliance cars Renault-Nissan, so many lamps are also suitable for Renault Logan/Sandero second generation. But there are nuances: for example, in the restyled versions (since 2016), some types of bases have changed. We have collected up-to-date information on all lighting devices - from low beams to license plate lights.

What lamps are in Nissan Almera G15 from the factory

Standard equipment Almera G15 (2012–2019) involves the use of halogen lamps in the head optics and LEDs in the parking lights/brake lights (depending on the year and configuration). Below is a table with factory types of lamps for the main lighting fixtures:

Lighting device	Lamp type (base)	Power, W	Notes
Low beam	H7	55	Halogen, restyled versions may have LED analogues
High beam	H1	55	In some configurations - HB3 (9005)
Fog lights (PTF)	H11 or H8	55	Depends on the market (European versions - H11)
Side lights (front)	W5W (baseless)	5	In the restyling there are LEDs (non-replaceable, in the headlight)
Brake/tail lights	P21/5W (two-pin)	21/5	Complete sets with LED optics include non-separable modules

It is important to consider that in Almera G15 after restyling in 2016, some of the lamps became non-removable — for example, the dimensions and daytime running lights (DRL) are integrated into the headlight unit and can only be replaced together with it. Also in top trim levels (TEKNA) could be installed xenon headlights (base D1S), but this is rare for the Russian market.

⚠️ Attention: In low beam lamps H7 brands are often counterfeited Osram And Philips. Check for the presence of a hologram on the packaging and markings on the base - the originals have an engraved logo.

How to choose replacement lamps: halogen vs LEDs vs xenon

The choice of lamp type depends on your goals: improving visibility, saving energy or legality (compliance with traffic regulations). Let's look at the pros and cons of each option:

• 🔆 Halogen lamps - standard option, cheap and easy to replace. Cons: Short lifespan (300-500 hours), high heat, dim light compared to LEDs.
• 💡 LED lamps — brighter than halogen by 200–300%, lasts up to 30,000 hours, but requires proper installation (need CAN bus snag to avoid errors on the dashboard).
• ⚡ Xenon lamps - maximum brightness and range of light, but Installation in halogen headlights is prohibited by traffic regulations (fine 3,000 rubles). Legal only in standard xenon headlights.

For Almera G15 optimal balance of price and quality - premium halogen lamps (For example, Osram Night Breaker or Philips X-tremeVision) or certified LEDs with the correct light beam (eg H7 LED by Morimoto). The latter will cost 3–5 times more, but will last 10 times longer.

When choosing LEDs, pay attention to light temperature:

• 🔵 4300–5000K — white neutral light, optimal for the city.
• 🔴 6000K and above - a cold bluish tint, illuminating the road worse in the rain.

⚠️ Attention: LEDs with a cooling radiator (aluminum or copper) last longer, but may not fit into the standard headlight reflector Almera G15. Before purchasing, check the dimensions of the lamp!

Step-by-step instructions for replacing low beam lamps H7

Replacing the low beam lamp in Almera G15 does not require special tools, but there are some nuances. For example, the washer reservoir in the right headlight is in the way - you will have to temporarily remove it. Here are the detailed instructions:

Plastic clip remover (or flat screwdriver)

New lamp H7 (do not handle with bare hands - grease marks will shorten the service life!)

Gloves (to avoid leaving fingerprints on the lamp glass)

Flashlight or phone with light-->

1. Open the hood and disconnect the negative terminal of the battery (to avoid short circuit).

2. Remove the rubber boot from the back of the headlight unit (it is held on by latches).

3. Disconnect the power connector from the lamp by pressing the latch.

4. Disengage the spring clip (pull it up and to the side).

5. Carefully remove the old lamp, holding it by the base. Do not touch the glass flask!

6. Install the new lamp, aligning the tabs on the base with the grooves in the headlight. Secure with a clamp and connect the connector.

After replacement, check the operation of the headlight by turning on the low beam. If the lamp does not light, check:

• 🔌 The connector is connected correctly (sometimes the contacts oxidize).
• 🔧 Reliable fixation of the spring clamp.
• 💡 The integrity of the lamp itself (there are defective copies).

What to do if the lamp quickly burns out after replacement?

There may be several reasons:

1. **Poor contact in the connector** - oxidation or burning of the terminals. Clean them with fine sandpaper.

2. **Increased voltage in the on-board network** (more than 14.5 V). Check with a multimeter at idle speed.

3. **Vibrations** - if the lamp is not fixed tightly, the filament wears out faster. Make sure the spring clip is fully engaged.

4. **Poor quality of the lamp** - cheap analogues often have a thin filament that burns out in 1-2 months.

Features of replacing lamps in rear lights

Tail lights in Almera G15 less capricious than front optics, but there are pitfalls here too. For example, in some versions, to access the lamps you need to remove the trunk trim. Let's look at the process using the example of replacement brake light (P21/5W):

1. Open the trunk and locate the plastic cover on the inside of the light. It is secured with two latches.

2. Remove the cover and pull out the lamp socket by turning it counterclockwise.

3. Press the lamp and rotate it 45° to the left, then remove it.

4. Install a new lamp P21/5W, aligning the protrusions with the grooves in the cartridge.

To replace the lamp reverse (base W16W) or turn signal (base PY21W) the algorithm is similar. The main thing is not to confuse the cartridges, since they are similar in appearance.

⚠️ Attention: On versions with LED tail lights (e.g. Almera G15 2018+) lamps are not replaced - if they fail, the entire unit must be replaced. The cost of the original lantern is from 8,000 rubles.

Common mistakes when replacing lamps and how to avoid them

Even experienced car owners sometimes make mistakes that lead to rapid lamp burnout or electrical damage. Here are the most common:

• 🧤 Touching the flask with bare hands — oil from the fingers leads to local overheating of the glass. Use gloves or wipe the flask with alcohol.
• 🔌 Wrong polarity - especially relevant for LEDs. If the lamp does not light, turn it 180°.
• 🔧 Using too powerful lamps (for example, 100 W instead of 55 W). This leads to melting of the wiring and clouding of the headlight glass.
• 💡 Purchasing lamps without certification — cheap Chinese LEDs can blind oncoming drivers and cause complaints from the traffic police.

Another typical problem is error on the dashboard after installing the LEDs. This occurs due to the low resistance of LED lamps (the on-board computer perceives them as burnt out). Solution - installation fake resistors (resistance 6–12 Ohm) or CAN bus adapters.

Review of the best lamps for Nissan Almera G15 in 2026

Based on reviews from owners and tests by independent experts, we have compiled a rating of lamps for Almera G15 in different categories:

Category	Lamp model	Type/base	Pros	Cons
The best halogen	Osram Night Breaker Laser	H7, H1	+20% brightness, long service life	Price (~1,200 rub. per pair)
Best LED	Morimoto 2Stroke 2.0	H7	Ideal light beam, 6000K	Requires CAN bus snag
Budget option	Philips LongLife EcoVision	H7, P21/5W	Low price (~300 rub.), resource 1500 hours	Light is dimmer than premium models
For PTF	Narva Range Power H11	H11	Vibration resistant, bright yellow light	Not suitable for LED replacement

For LEDs, we recommend paying attention to models with active cooling (built-in fan), since passive radiators often overheat in cramped headlights Almera G15.

Legal aspects: what is allowed and what is not

In Russia there are strict requirements for lighting devices (GOST R 51709-2001 and Technical Regulations of the Customs Union). Here's what owners need to know Almera G15:

• ✅ Allowed:
• 🔆 Use of halogen lamps with markings ECE R37 (for H7, H1, etc.).
• 💡 Installation of LEDs, if they are certified for your headlight model (the packaging must indicate ECE R112 or ECE R128).
• ❌ Prohibited:
• ⚡ Xenon in halogen headlights (fine 3,000 rubles under Article 12.5 of the Administrative Code).
• 🔴 LEDs without certification or with the wrong light beam (they blind oncoming drivers).
• 🟡 Lamps with a higher color temperature 6000K (blue/violet light).

Before purchasing LEDs, check to see if their specifications indicate compatibility with your headlight model. For example, for Almera G15 LED lamps with markings are suitable For Halogen Projector or For Reflector Headlight.

FAQ: Frequently asked questions about lamps in Nissan Almera G15

Is it possible to put LEDs in PTF? Almera G15?

Technically yes, but legally - only if the lamps are certified according to ECE R112. Otherwise, the inspector may issue a fine for non-conforming lighting fixtures. In addition, in fog, LEDs penetrate a dense veil worse than halogen ones. H11 with yellow light.

Why do H7 lamps burn out quickly after replacement?

There are several reasons:

1. Poor quality lamps (buy only proven brands: Osram, Philips, Narva).
2. Increased voltage in the on-board network (check the generator).
3. Vibrations (if the lamp clamp is not fully latched).
4. Oxidation of contacts in the connector (clean them with sandpaper).

How to remove a headlight Almera G15 to replace the lamp?

To remove the headlight you will need:

1. Disconnect battery.
2. Remove the bumper (unscrew the 6 bolts from the bottom and 4 clips from the top).
3. Disconnect the headlight power connectors.
4. Unscrew the 3 headlight mounting bolts (two on top, one on bottom).

You can replace the lamps without removing the bumper, but access will be limited.

What are the dimensions of the lamps? Almera G15 2018?

In restyled versions (2016–2019), the side lights and DRLs are made using LEDs and cannot be replaced separately. If it fails, the entire headlight unit must be replaced (original article number: 26510-4M00A for the right one, 26520-4M00A for the left).

Which is better: Osram or Philips for Almera G15?

Both brands offer high-quality lamps, but there are nuances:

• Osram Night Breaker - 20% brighter, but last less (~400 hours).
• Philips X-tremeVision - longer service life (up to 600 hours), but the light is slightly cooler.
• Philips LongLife — optimal for those who drive little (lifetime up to 1500 hours).

For LED it is better to choose Morimoto or Diode Dynamics - they provide the correct light beam without glare.