<em>Nissan Qashqai J10</em>trunk lid: how to remove, adjust and replace

Nissan Qashqai J10 (first generation, 2007–2013) - one of the most popular crossovers on the Russian market. However, as owners age, they often have problems with trunk lid: it sags, creaks, does not lock, or refuses to open at all. In this article, we will look at all the nuances of repairing, adjusting and replacing the rear door, and also tell you how to avoid common mistakes when working with the mechanism.

Trunk lid design Qashqai J10 includes gas stops (shock absorbers), lock, hinges and electric drive (in versions with electric opening). Most malfunctions are associated with wear of these elements, but some problems can be corrected independently, without the help of a service station. Next are detailed instructions with photos, diagrams and useful life hacks.

Typical trunk lid problems Qashqai J10

Before you begin repairs, it is important to correctly diagnose the problem. Here are the most common symptoms and their possible causes:

• 🔧 The lid sag or does not stay open — wear of gas shock absorbers, weakening of hinges or deformation of the body.
• 🔊 Creaks and extraneous sounds when opening/closing - lack of lubrication in the hinges, corrosion or damage to the seal.
• 🔒 The lock does not lock or is difficult to open — breakdown of the lock mechanism, wear of the cylinder or problems with the electric drive (in versions with a button).
• ⚡ Electric drive does not work — the fuse has blown, the contacts have oxidized, or the motor has failed.
• 💧 Water leaks in the trunk — damage to the sealing rubber or loose fit of the lid.

If the trunk lid doesn't open at all (even from inside), do not try to apply force - this may lead to deformation of the hinges or breakage of the lock cable. In such cases, it is better to immediately contact an auto electrician or use an emergency opening method (we will discuss this below).

⚠️ Attention! On Qashqai J10 with electric trunk lid ("Power Liftgate" option) it is strictly forbidden to block its movement with your hand during automatic opening/closing. This may damage the drive gearbox.

How to remove the trunk lid Nissan Qashqai J10: step by step instructions

Removing the cover may be necessary to replace hinges, gas stops, or repair the body. The procedure does not require a special tool, but will require an assistant - the weight of the glazed lid is about 15–20 kg.

You will need:

• 🔧 Socket wrench on 10 mm And 12 mm.
• 🔧 Screwdriver with a Phillips bat (for plastic sheathing).
• 🧴 WD-40 or similar lubricant (if the bolts are sour).
• 🧤 Gloves (so as not to scratch the paintwork).

Sequence of actions:

1. Disconnect the battery (especially if you have the electric version).
2. Remove the plastic trim inside the trunk by unscrewing the screws around the perimeter and carefully prying up the clips.
3. Disconnect the wiring harness from the lock and (if equipped) the electric drive.
4. Have a helper support the cover, then remove the hinge bolts (according to 4 bolts per hinge).
5. Remove the cover from the body and place it on a soft surface (such as a blanket) to avoid damaging the glass.

Disconnect the battery (required!)

Remove the trunk trim

Disconnect electrical connectors

Prepare a support for the lid

Check availability of all tools -->

If the hinge bolts are soured, do not try to tear them off - treat them WD-40 and wait 10–15 minutes. Using excessive force may cause the threads in the body to break.

Adjusting hinges and gas stops

Over time, the trunk lid hinges Qashqai J10 become loose, and gas shock absorbers lose their tightness. This results in sagging, uneven opening or spontaneous closing. Adjusting the hinges and replacing the stops solves the problem in 90% of cases.

How to adjust hinges:

1. Loosen the hinge bolts (do not unscrew completely!).
2. Adjust the position of the cover so that the gaps around the entire perimeter are the same (the optimal gap is 3–5 mm).
3. Tighten the bolts firmly 20–25 Nm (do not overtighten!).
4. Check the operation of the lock - it should close without effort.

Replacing gas struts:

• 🔧 Buy new shock absorbers with art. 40520-4M000 (original) or analogues from Sachs or Stabilus.
• 🔨 Remove the plastic plugs from the hinges of the stops (pry them off with a screwdriver).
• 🔧 Unscrew the fastenings of the old shock absorber and install the new one (pay attention to the installation side - the left and right parts are not interchangeable!).

Problem	Reason	Solution
The lid falls off when opening	Wear of gas stops	Replacing shock absorbers (in pairs!)
Creak when moving	Lack of lubrication in hinges	Cleaning and Lubrication Litol-24 or CRC
Uneven gaps	Deformation of hinges or body	Adjusting or replacing hinges
The lock does not lock	Worn mechanism or wire	Lock repair or cable replacement

⚠️ Attention! If after adjustment the lid still closes with force, check sealing gum - it could be deformed or moved. In this case, it must be cleaned of dirt and reinstalled using special glue for rubber.

Standard (mechanical)

Electrically operated (Power Liftgate)

I don't know, I didn't pay attention -->

Repair and replacement of trunk lock

Trunk lid lock Qashqai J10 - one of the most vulnerable places. Over time, the mechanism becomes clogged with dirt, the cable rusts or breaks. If the key stops opening the trunk and the button on the remote control does not work, most likely the problem is in the lock or drive.

How to disassemble and repair the lock:

1. Remove the plastic cover from the inside of the cover (it is secured with clips).
2. Unscrew the lock mounting bolts (2 bolts 10 mm).
3. Disconnect the cable and electrical connector (if equipped).
4. Disassemble the lock, clean the mechanism from dirt and lubricate silicone grease.
5. Check the integrity of the cable - if it is torn, replace it (art. 73101-4M000).

If the lock is completely out of order, buy a new original (73100-4M000) or an analogue from Febi or TRW. Average asking price - 1,500–3,000 rubles.

What to do if the trunk cannot be opened with either a key or a button?

If the mechanical and electrical opening methods do not work, try the following:

1. Remove the trunk trim from the interior side (near the rear seats).

2. Find the emergency release cable (usually red) and pull it.

3. If the cable is broken, you will have to drill out the lock cylinder or contact an auto electrician to supply voltage to the drive.

Electric trunk lid: diagnostics and repair

Versions Qashqai J10 with option Power Liftgate are equipped with an electric drive, which may fail over time. Typical problems:

• ⚡ The lid opens jerkily or not completely.
• 🔋 The drive only works in one direction (for example, it opens but does not close).
• 🚨 There is an error on the instrument panel "Check Boot Lid".

Causes and solutions:

• 🔋 Low battery or low voltage - check the battery charge (must be at least 12.4 V).
• 🔧 Oxidation of contacts — clean the connectors of the drive and control unit.
• 🛠️ Reducer gear wear — the motor will need to be replaced (art. 28550-4M000).
• 📶 Position sensor malfunction — check the wiring and replace the sensor if necessary.

To reset an error "Check Boot Lid" you can use a diagnostic scanner (for example, ELM327) or disconnect the battery for 10 minutes. If the problem persists, contact an electrician to check the control unit.

Selection of spare parts: original vs analogues

When replacing trunk lid parts Qashqai J10 The question arises: should I buy original spare parts or analogues? Let's look at the pros and cons of each option.

Detail	Original (Nissan)	Analogs (Sachs, TRW, Febi)
Gas struts	Article: 40520-4M000 Price: ~3,500 rub./pair Pros: Precise fit, long service life	Article: Sachs 194 011 Price: ~2,200 rub./pair Pros: cheaper, good quality
Trunk lock	Article: 73100-4M000 Price: ~2,800 rub. Pros: full compatibility	Article: TRW GMB100 Price: ~1,500 rub. Pros: budget option
Loops	Article: 73200-4M000 (left), 73201-4M000 (right) Price: ~4,000 rub./pair	Article: Febi 35400 Price: ~2,500 rub./pair

If your budget is limited, you can choose analogues from trusted brands (Sachs, TRW, Febi). However, for such critical parts as loops, it is better to take the original - they can withstand heavy loads and last longer.

Prevention and care of the trunk lid

To avoid costly repairs, just follow these simple recommendations:

• 🧴 Lubricate the hinges 2 times a year (Litol-24 or CRC).
• 🧹 Clean the seal from dirt and snow so as not to damage the elastic band.
• 🚿 Wash the trunk with the lid openso that water does not accumulate in the lock mechanism.
• ⚡ Check the electric drive at the first sign of a malfunction (extraneous sounds, jerking).

If you often transport heavy loads, do not load the lid from above - this will lead to deformation of the hinges. To transport long items, use roof rack or trailer.

⚠️ Attention! On Qashqai J10 Do not use aggressive detergents when tinting the rear window - they can damage the film. Use only soft wipes and special cleaners.

FAQ: Frequently asked questions about the trunk lid Nissan Qashqai J10

Is it possible to repair the gas stop, or just replace it?

Gas shock absorbers cannot be repaired - they can only be replaced. Attempting to thread or solder the stop will cause it to rupture and possibly damage the cover.

How much does it cost to replace the trunk lid hinges at a service center?

The average cost of replacing one hinge is 1,500–2,500 rubles. If you change both hinges with adjustment, the price can reach up to 5,000 rubles (excluding spare parts).

Why does the trunk lid open by itself while driving?

This is a dangerous malfunction that is usually caused by:

• Wear of gas stops (they do not support the weight of the cover).
• Broken lock (does not lock position).
• Deformation of hinges or body.

Urgently check all the elements and do not operate the car until the problem is fixed!

How much weight can the trunk lid support? Qashqai J10?

Maximum load on open cover - up to 20 kg. Exceeding this value can lead to deformation of the hinges or failure of the gas stops.

Is it possible to install an electric drive on a version without it?

Technically possible, but you will need:

• Purchase of an electric drive kit (motor, control unit, wiring).
• Flashing BCM (body control unit).
• Installing an additional fuse.

The cost of such tuning is from 20,000 rubles (excluding work).