Clips for Nissan Qashqai J11: how to choose and install without errors

Clips are small but critical parts on which the strength of the fastening of bumpers, cladding and interior elements depends. Nissan Qashqai J11 (2014–2021). Their breakage or wear can lead to plastic rattling, moldings falling off, or even damage to the body when driving. In this article we will look at what clips are used on Qashqai J11, how to choose them correctly by article number, where to buy original and analogues, and we will also give step-by-step instructions for replacement without damaging the body.

Model feature J11 - a combination of metal and plastic clips of different diameters. For example, to attach the front bumper, use 90° clips with snap, and for the rear facing - pistons with rubber seal. An incorrect choice even by 1–2 mm can lead to the part dangling or, conversely, cracking during installation. We have collected current data on article numbers, compatibility with restyled versions (2017–2021) and life hacks from car mechanics.

Types of clips for Nissan Qashqai J11: where are they located?

On Qashqai J11 More than 15 types of clips are used, differing in material, diameter and method of fastening. The main areas of their application:

• 🔧 Front bumper: clips with a metal core (diameter 8–10 mm) and plastic latches for attaching to the wing.
• 🚗 Rear bumper: pistons with a rubber ring (for tightness) and herringbone clips for moldings.
• 🪟 Arch cladding: plastic clips with a wide cap (prevent dirt from entering).
• 🚪 Doors and interior: mini-clips for fastening the trim and push-button fasteners for the instrument panel.

The most problematic areas - clips for fastening the front bumper to the fender liners. They often break when dismantled to replace lamps or parking sensors. Original articles of these clips: 77010-4M000 (metal) and 77010-1X000 (plastic). Analogues from Febi or Hella 30–40% cheaper, but may not withstand severe frosts (the rubber hardens).

For the rear facing, clips with an article number are used 77010-3W000 (rubber seal) and 77010-1W000 (“herringbone” for moldings). Important: on restyled versions (since 2017), the diameter of the holes for the clips in the rear bumper has changed - now they are located there universal caps 9.5 mm instead of 9 mm.

Article numbers of original clips and their analogues

Original clips from Nissan are marked with a series 77010-XXXX, where the last digits indicate the type and size. Below is a table with the most popular items for Qashqai J11 (dorestayl and restyle):

Mounting area	Original article	Analogs (brand/article)	Price, rub. (original/analogue)
Front bumper (to fender)	77010-4M000	Febi 15476, Hella 8XH 351 309-121	250 / 120–150
Rear bumper (to body)	77010-3W000	SWAG 30 92 7701, Meyle 100 770 0003	300 / 160–190
Arch cladding	77010-1X000	Corteco 25010010, Topran 101 770	180 / 80–100
Salon (door trim)	77010-5W000	Dorman 77010, URO Parts 770101X000	120 / 50–70

When choosing analogues, pay attention to material: clips for external panels must be made of polypropylene with rubber seal, and for the interior - from softer plastic (for example, polyethylene). Cheap Chinese analogues (for example, nameless ones with AliExpress) often break during the first dismantling.

⚠️ Attention: On restyled Qashqai J11 (2017–2021) rear bumper clips have increased cap diameter (9.5 mm instead of 9 mm). Installing old clips will lead to play and rattling on bumps.

How to remove old clips without damaging the body

The main mistake during dismantling is trying to pull out the clip perpendicular body. This almost always ends in broken plastic or a bent metal core. Correct algorithm:

1. Treat the clip silicone grease (For example, WD-40 Specialist) and wait 5–10 minutes.
2. Pry up the clip plastic pick (not a screwdriver!) from the side, pressing the latch.
3. Rotate the clip counterclockwise 10–15° and pull parallel to the body.

For hard-to-reach clips (such as under headlights), use special puller type Kukko 21/1 or a homemade device from a bicycle spoke. If the clip is broken and the core remains in the body, it can be unscrewed pliers with thin jaws or drill with a drill with a 3 mm drill bit (carefully so as not to damage the paintwork!).

Plastic pick or clip remover|Silicone lubricant (WD-40, Liqui Moly)|Pliers with thin jaws|Flashlight for illuminating hard-to-reach places|A set of replacement clips-->

Pay special attention to the clips fender liner fastenings. They often rust and stick to the body. In this case it will help penetrating lubricant (For example, PB Blaster) and heating with a hair dryer (up to 60–70°C). Do not use open flames - this will damage the plastic parts!

Step-by-step instructions for installing new clips

Before installing new clips, be sure to clean the holes in the body from dirt and rust. To do this use wire brush And degreaser (For example, acetone or white spirit). Installation algorithm:

1. Check the diameter of the clip and the hole. For Qashqai J11 permissible play - no more than 0.3 mm.
2. If the clip has a rubber seal, apply silicone grease for better sealing.
3. Install the clip at an angle of 15–20° and press until it clicks. Do not use excessive force - this may bend the body!
4. After installation, check the reliability of the fastening by pulling the part towards you. Play of more than 1–2 mm is unacceptable.

For herringbone clips (e.g. 77010-1W000) use special tool — clip installer (sold in car repair kits). It allows you to evenly distribute the force and avoid distortion. If you don’t have a tool, you can carefully install the clip hammer through a wooden spacer.

After replacing the clips, be sure to check gaps between parts. For example, between the front bumper and the fender, they must be the same on both sides (tolerance - ±1 mm). If the gap is larger, the clip may be installed incorrectly or the wrong model may be selected.

Common mistakes when replacing clips and how to avoid them

Even experienced car owners make mistakes that lead to repeated repairs. Here are the most common:

• 🔨 Using the wrong clips. For example, installing clips from Renault Duster (they are similar in appearance, but have a different fixation angle).
• 🛠️ Drag the clips. This leads to plastic deformation and cracks. The maximum installation force is 5–7 kg.
• 🌡️ Low temperature operation. Plastic becomes brittle when below +5°C, and the clips break during installation.
• 🔧 Ignoring Corrosion. Rust in body openings will cause new clips to wear out faster.

On the restyled Qashqai J11 (2017+), the front bumper clips have a reinforced metal insert. If you install old clips instead (before 2017), the bumper will “walk” when driving off-road.

⚠️ Warning: Never use superglue or sealant for fixing clips. This will make them non-removable and damage the paintwork the next time it is dismantled. Suitable for temporary fixation 3M double sided tape (For example, 3M VHB 4910).

Where to buy clips for Nissan Qashqai J11: trusted suppliers

Original clips can be ordered from official dealers Nissan, but their price is often 2–3 times higher. Optimal purchase options:

• 🛒 Online spare parts stores: Exist.ru, Autodoc.ru, Kolesa-Darom.ru. There is a filter by article number and compatibility reviews.
• 🏬 Car accessories stores: AutoSpetsCenter, IXORA. They often sell sets of clips for a specific model.
• 🌍 Foreign sites: Amazon, eBay, AliExpress (only for verified sellers with a rating above 98%).

When purchasing, pay attention to:

• 📦 Packaging: original clips Nissan come in branded bags with a logo.
• 📏 Dimensions: Compare the diameter and length of the clip with the original (you can use caliper).
• 📄 Certificates: for high-quality analogues (for example, Febi or SWAG) there is a certificate ISO 9001.

Average cost of clip sets for Qashqai J11:

• Set of 10 original clips - 1,500–2,000 rub.
• Set of 20 analogues (Febi, Meyle) — 800–1,200 rub.
• Universal clips (China) — 300–500 rub. (risk of defects 30–40%).

How to distinguish an original clip from a fake?

Original clips Nissan have:

1. Brand logo on the cap (embossed, not glued on).

2. Smooth plastic without burrs or bubbles.

3. Metal core (if provided) with anti-corrosion coating.

4. Packaging with an article number matching the catalog Nissan (check by parts.nissan.eu).

Frequently asked questions about clips on Qashqai J11

Can clips from other Nissan models be used?

Yes, but with reservations. For example, clips from Nissan X-Trail T32 (article 77010-4M00A) suitable for front bumper Qashqai J11, but have a slightly different fixation angle. Clips from Juke F15 incompatible due to smaller diameter. Always check the catalogs Nissan or consult with the seller, providing the VIN of your car.

How many clips are needed to completely replace the front bumper?

For removing and installing the front bumper Qashqai J11 required 12 clips:

• 4 clips 77010-4M000 (attachment to wings),
• 6 clips 77010-1X000 (attachment to subframe),
• 2 clips 77010-5W000 (fastening moldings).

We recommend buying a set with a spare of 2-3 pieces - when dismantling 1-2 clips, they often break.

What glue can be used to temporarily fix the clips?

Suitable for temporary fixation:

• Double sided tape: 3M VHB 4910 (withstands up to 5 kg per tear).
• Adhesive sealant: ABRO AB-11AB (removed without traces).
• Liquid nails: Moment Installation Superstrong Plus (only for metal surfaces!).

⚠️ Do not use epoxy glue or welding - this will damage the plastic and make the clips non-removable.

What to do if the clip has fallen inside the body?

If the clip has fallen inside a door or arch, try:

1. Use magnetic grip (sold in hardware stores).
2. Remove door trim or fender liner (depending on the zone).
3. Apply vacuum cleaner with narrow nozzle (suitable for lightweight plastic clips).

If the clip is metal and is stuck in the body, you may need to drill a hole (only as a last resort!).

Do I need to lubricate the clips before installation?

Yes, lubrication makes installation easier and extends the life of the clips. Recommended compositions:

• Silicone grease: WD-40 Specialist, Liqui Moly Silicone-Fett.
• Graphite grease: Suitable for metal clips.
• Anti-squeak paste: Liqui Moly Kunststoff-Pflege (prevents squeaks).

Do not use Litol or Solid oil - they attract dust and accelerate wear of the plastic.