<em>Nissan Juke</em>hood: complete repair and maintenance manual

Hood Nissan Juke - this is not just a body element, but a key part on which access to the engine, battery and other vital vehicle systems depends. Owners of this compact crossover often encounter problems: from a banal jammed lock to the need to completely replace the hood after an accident. In this article we will analyze all the nuances - from simple opening to complex repairs, so that you can cope with the task without contacting service.

Feature Juke (especially models 2010–2019) lies in the non-standard design of the hood lock, which differs from classic solutions Nissan. This often causes difficulties for beginners. We have collected proven methods, instructions with photos and videos, as well as list of common mistakeswhich may cause damage. If you plan to maintain your own Juke, this material will be your find.

How to open the hood Nissan Juke: step by step instructions

At first glance, opening the hood to Juke no different from other cars, but it has its own tricks. The main problem is non-obvious lever location in the cabin and features of the locking mechanism. If you have never opened the hood on this model, follow the algorithm:

1. Find the hood release lever — it is located to the left of the steering column, under the dashboard. On models Juke 2015–2020 the lever can be hidden by a plastic plug.
2. Pull the lever towards you until a characteristic click occurs. This will release the main lock, but the hood will not open yet - it is held in place by the safety hook.
3. Move to the front of the car, find the gap between the hood and the radiator grille. Insert your hand and feel safety hook lever (it is on the right in the direction of travel).
4. Push the lever up and at the same time lift the hood. If the hook does not budge, do not use force - check whether the main lock is completely released.

If the hood doesn't open the first time, don't panic. Often the problem lies in contamination of the mechanism or cable corrosion. In this case, WD-40 or a similar lubricant will help, which must be applied to the lock through the technological hole in the radiator grille.

Important! On models Juke with gas shock absorbers (installed from the factory on versions after 2017) the hood opens smoothly, but if the shock absorbers are worn out, it can fall sharply. Always hold the hood with your hand when opening it.

Typical hood malfunctions Nissan Juke and their reasons

Hood Juke subject to several characteristic problems that occur more often than on other models Nissan. Here are the main ones:

• 🔧 Lock jammed - most often caused cable corrosion or dirt getting into the mechanism. This is especially true for vehicles operated in high humidity conditions.
• 💥 Cracks on the hood - plastic body elements Juke (especially on models 2010–2014) are prone to cracking at low temperatures or after minor impacts.
• 🔄 Problems with gas shock absorbers — over time, they lose their tightness, and the hood no longer locks in the open position.
• 🔑 Broken safety hook - often breaks due to excessive force or after an accident.

One of the most unpleasant situations is Broken hood release cable. In this case, you will have to remove the radiator grille or front bumper to gain access to the lock. If the cable is simply jammed, you can try to “free” it with lubricant and light tapping on the mechanism.

What to do if the cable breaks?

If the cable breaks, you will need:

1. Remove the radiator grille (4 bolts from below and 2 clips from above).

2. Find the hood lock and manually move it to the open position with a screwdriver or pliers.

3. After opening the hood, replace the cable (part number for Juke: 28510-4M00A).

If you are not confident in your abilities, it is better to contact a service center - incorrect dismantling of the grille can damage the climate control.

Another common problem is hood misalignment after replacement or repair. This occurs due to improper adjustment of the hinges or deformation of the body. In this case, the hood may not close completely or, conversely, require excessive force when closing.

How to remove the hood Nissan Juke: detailed instructions with photos

Removing the hood Juke will be required when replacing it, painting or repairing hinges. The process is not complicated, but requires care so as not to damage the paintwork. You will need:

• 🔧 Key on 10 mm (for hinge bolts).
• 🔧 Screwdriver with a flat blade (for removing plastic clips).
• 🧲 Magnet or container for fasteners (so as not to lose bolts).
• 👨‍👦 Assistant (the hood is heavier than it looks!).

Step by step instructions:

1. Open the hood and secure it in the open position (use a stop or ask an assistant to hold it).
2. Disconnect the negative battery terminal (required for safety!).
3. Remove the plastic plugs from the hood hinges (they are attached to clips, pry them off with a screwdriver).
4. Unscrew the hinge bolts - by 2 bolts per hinge (use the key on 10 mm). Do not unscrew the bolts completely - first loosen them, then support the hood and remove the bolts completely.
5. Remove the hood together with an assistant, carefully lifting it up. Be careful - there may be wires connected to the hood (for example, an opening sensor on some versions).

If you are removing the hood for painting, be sure to mark the location of the loops with a marker or take a photo - this will help avoid problems during reinstallation. Also check the condition rubber seals on hinges - if they are worn out, it is better to replace them (article: 68110-4M000).

Open the hood and secure it

Disconnect the battery terminal

Remove the plastic plugs from the hinges

Loosen the hinge bolts (do not unscrew completely!)

Prepare a place for the hood (soft bedding) -->

Hood adjustment Nissan Juke: eliminate distortions and cracks

After removing/installing the hood or an accident, it often becomes necessary to adjust it. An incorrectly adjusted hood can:

• 🚗 Do not close completely (there remains a gap).
• 🔊 make squeaks when moving.
• 💨 Let water into the engine compartment.

Adjustment is carried out by changing the position of the loops. You will need a key for 10 mm and assistant. Follow the algorithm:

1. Check clearances along the entire perimeter of the hood. Ideally they should be the same (3–5 mm).
2. Loosen the hinge bolts (not completely!) and adjust the position of the hood:
• Vertical position — adjustable by moving the loop up/down.
• Horizontal position — changes by shifting the loop forward/backward.

Close the hood and check how it fits. If there is misalignment, repeat the adjustment.

Tighten the hinge bolts after achieving the ideal position.

If the hood "walks" When closing, the problem may be worn hinges or loose lock bolts. In this case, the hinges will need to be replaced (part number: 68100-4M000 for the left, 68101-4M000 for the right one) or tightening the lock bolts.

Replacing the hood lock Nissan Juke: when required and how to do it

Hood lock on Juke is a consumable item that can fail due to:

• 🔑 Mechanical wear (usually on cars with mileage >150 thousand km).
• 💦 Corrosion (especially relevant for cars from Europe or coastal regions).
• 🚗 Road accident (even a slight impact can deform the mechanism).

Signs of a faulty lock:

• The hood does not lock in the closed position.
• The lever in the cabin does not return to its original position.
• Extraneous sounds (creaks, clicks) when opening/closing.

To replace the lock you will need:

• New lock (original article: 28500-4M00A, analogues: Febi 28500, TRW JTC1005).
• Key on 10 mm and a screwdriver.
• Lubricant (eg Liqui Moly LM40).

Replacement instructions:

1. Open the hood and lock it.
2. Remove the plastic protection from the lock (attached with 2 clips).
3. Unscrew 3 bolts fastening the lock (key on 10 mm).
4. Disconnect the cable from the lock (remember its position!).
5. Install the new lock in reverse order.
6. Adjust the position of the lock so that the hood closes without effort.

After replacing the lock Be sure to check the operation of the safety hook — it must securely fix the hood in the open position. If the hook is damaged, replace it (part number: 28515-4M000).

Repairing cracks and dents on the hood Nissan Juke: Can I do it myself?

Hood Juke made of thin metal (on early models) or plastic (on restyled versions after 2014), so it is especially susceptible to cracks and dents. If the damage is minor, you can fix it yourself:

Type of damage	Repair method	Required materials	Cost (on your own)
Minor scratches	Polish or wax pencil	Polish, microfiber, wax pencil	200–500 ₽
Shallow dents (without damage to paintwork)	Vacuum drawing or PDR technology	PDR kit, hair dryer, adhesive suction cup	1 000–3 000 ₽
Cracks in the plastic hood	Epoxy resin bonding + fiberglass reinforcement	Epoxy, fiberglass, putty, paint	2 500–5 000 ₽
Deep dents with paint damage	Straightening + putty + painting	Putty, primer, paint, varnish	5 000–15 000 ₽

For repairing cracks in a plastic hood Juke (valid for models 2014–2020) follow the instructions:

1. Clean the crack sandpaper (P80–P120).
2. Degrease the surface (use White spirit or Antisilicone).
3. Apply epoxy resin on a crack on the inside of the hood.
4. Reinforce with fiberglass (2-3 layers).
5. Putty and paint damaged area.

If the crack is through or the hood is severely deformed, it is better to consider replacing it. Price of a new hood for Juke (original) - from 25 000 ₽, analogue (for example, Febi or Dello) - from 12 000 ₽.

Common mistakes when working with the hood Nissan Juke and how to avoid them

Even experienced car owners make mistakes when repairing or adjusting the hood Juke. Here are the most common of them:

⚠️ Attention! Never try to open the hood by prying it with a screwdriver through the gap between the hood and the fender. This will lead to damage to paintwork and deformation of the hood edges. If the lock is stuck, use lubricant or remove the radiator grille.

• 🔧 Tightening the hinge bolts - this leads to deformation of the hinges and difficulty opening the hood. Bolts must be tightened firmly 10–12 Nm.
• 🔨 Using non-original hinges — cheap analogues often do not match in geometry, which leads to hood misalignment.
• 🎨 Painting the hood without primer - on plastic hoods Juke paint without primer peels off quickly.
• 🔑 Replacing the cable without lubrication — a new cable without lubrication will last no more than a year.

Another common mistake is ignoring the safety hook. Many owners Juke they forget to check its operation after adjusting the hood, which can lead to spontaneous opening of the hood while driving. Always test your hook before your trip!

⚠️ Attention! When replacing gas hood shock absorbers, never use shock absorbers from other models. Nissan (for example, from Qashqai or X-Trail). Even if they are similar in appearance, their force and length may differ, resulting in sudden drop of the hood or the inability to close it.

FAQ: Frequently asked questions about the hood Nissan Juke

Is it possible to open the hood Nissan Jukewhat if the cable breaks?

Yes, but to do this you will have to remove the radiator grille or front bumper to gain access to the lock. An alternative method is to insert a thin screwdriver through the gap in the grille and try to dislodge the lock mechanism. If the cable breaks inside the passenger compartment, you will need to remove the panel under the steering wheel to replace it.

What is the weight of the hood Nissan Juke? Is it possible to remove it alone?

The weight of the hood depends on the material:

• Metal hood (until 2014) — 12–14 kg.
• Plastic hood (after 2014) — 8–10 kg.

Theoretically, you can remove the hood alone, but this is inconvenient and dangerous - there is a high risk of scratching the fenders or damaging the hinges. We recommend working with an assistant.

What to do if the hood Juke Doesn't close all the way?

The reasons may be as follows:

1. Skewed hinges - adjustment required.
2. Wear of rubber seals - replace them.
3. Deformation of the lock or hood - replacement may be required.
4. Entry of foreign objects into the lock mechanism (leaves, dirt).

Start by visually inspecting and adjusting the hinges. If the problem persists, check the lock.

Is it possible to install a hood from another model? Nissan on Juke?

No, hood Juke unique in shape and fastenings. Even the hoods are from Nissan Qashqai or X-Trail, despite the external similarity, will not fit due to different:

• Sizes and shapes.
• Loop locations.
• Lock fastenings.

The exception is hoods from restyled versions Juke (for example, pre-restyle 2010–2014 and restyle 2014–2020), but even here there may be nuances with the fastening of gas shock absorbers.

How much does it cost to replace a hood Nissan Juke in the service?

The cost depends on the type of work and region:

• Replacing the hood (without painting) — 3 000–6 000 ₽.
• Hood replacement + painting — 15 000–30 000 ₽ (depending on complexity).
• Crack repair (plastic) — 5 000–10 000 ₽.
• Adjusting the hinges — 1 000–2 000 ₽.

You can save money by purchasing a hood yourself (for example, a used one in good condition for 8 000–15 000 ₽) and contacting the service only for installation.