Rear bumper Nissan Qashqai J10 restyling (2014–2021) is one of those parts that sooner or later requires dismantling: be it replacement after an accident, installing parking sensors, painting or repairing a tow bar. Unlike the pre-restyling version, the restyled bumper is attached slightly differently, which often raises questions among owners. This article will help you understand the process without contacting the service - with step-by-step photos, tips on tools, and warnings about common errors.
It is important to understand that dismantling the bumper Qashqai J10 restyling requires care: the plastic clips are fragile, and incorrect removal can damage the fasteners or wiring (if you have a version with a camera or parking sensors). We will analyze the process using the example of a bumper with parking sensors and rear view camera, but the instructions are also suitable for basic configurations. Let's get started!
Preparation: tools and working conditions
Before removing the rear bumper Nissan Qashqai J10, make sure you have everything you need. It is better to work in a garage or on a level area - this will protect the plastic from scratches and simplify access to the lower fasteners. Here is the full list of tools:
- 🔧 10 mm socket wrench (for bolts securing the bumper to the body).
- 🔧 Screwdriver with Phillips bit (PH2) - for self-tapping screws in the arches and under the license plate.
- 🔧 Plastic puller or flathead screwdriver (for clips, but not metal - it will damage the plastic!).
- 🔧 Jack and stops (if you need to lift the car to access the lower bolts).
- 🔧 Duct tape or marker — to mark sensor wires when disconnected.
- 🔧 Flashlight or head light — lighting will simplify work in hard-to-reach places.
If you have version with rear view camera, additionally prepare:
- 📸 Small flathead screwdriver to carefully remove the camera from its socket.
- 🔌 Multimeter (optional) - to check the integrity of the wiring after removal.
- Yes, it worked
- Yes, but the clips are broken
- No, I'm afraid of hurting you
- No, but I plan to
Don't forget about these precautions:
⚠️ Attention: If the car was parked outside, let the plastic of the bumper warm up to room temperature (especially in winter). Cold plastic becomes brittle and may crack when removing the clips.
Step by step instructions: Removing the rear bumper
We begin dismantling by preparing the machine. If you have installed tow bar, it will have to be removed in advance - it interferes with access to the lower bumper mounts. Next we follow the algorithm:
Step 1: Dismantling the plastic plugs and screws in the arches
1. Open the trunk and remove the plastic sill trim (it is held on by 4-5 clips). Pry it off with a puller, starting from the corner.
2. In the wheel arches, find the 2 screws on each side (they are hidden under small plastic plugs). Unscrew them with a Phillips screwdriver.
3. If you have version with all-wheel drive, additionally unscrew the screw under the rear bumper next to the exhaust pipe.
Step 2: Unscrew the bolts securing the bumper to the body
1. Under the license plate, remove the plastic cover (it is held on by 2 clips). Hidden underneath 2 bolts 10 mm - Unscrew them with a socket wrench.
2. Move to the bottom of the bumper. There you will find more 4 bolts (2 on each side), which attach the bumper to the side members. It is more convenient to unscrew them by lifting the car on a jack or driving onto an overpass.
The battery has been disconnected (if you are working with electrics)|The plugs in the arches and under the license plate have been removed|All screws and bolts have been unscrewed (10 pieces in total)|Tools have been prepared for removing the clips-->
Step 3: Removing the Clips and Detaching the Bumper
This is the most critical stage. Bumper Qashqai J10 restyling is attached to the body on 6–8 plastic clips (depending on the configuration). To remove them:
- Start at the corner of the bumper. Carefully pry it with the puller and pull it towards you.
- The clips should come out with a characteristic click. If the clip does not budge, do not use force - it is better to check that all the bolts are unscrewed.
- After removing the clips from one side, move to the other, evenly disconnecting the bumper along the perimeter.
If you have version with parking sensors or camera, before completely removing the bumper, disconnect the connectors:
- 🔌 Parking sensors: gently press the latch and pull out the plug.
- 📷 Rear view camera: remove it from the bumper by prying it with a screwdriver (it is attached to the latches), then disconnect the connector.
If the clip breaks during dismantling, do not panic - it can be replaced with a new one (article for Qashqai J10: 77110-4M000). Buy 2-3 pieces in advance for reserve.
Common mistakes and how to avoid them
Even experienced car owners sometimes make mistakes when removing the bumper. Here are the most common ones and how to prevent them:
| Error | Consequences | How to avoid |
|---|---|---|
| Unscrewing bolts when the bumper is cold | Cracked plastic or broken clips | Warm up the bumper with a hairdryer or let the car sit warm for 1–2 hours |
| Use of force when removing clips | Broken fasteners, damaged body paintwork | Use a plastic puller and swing the bumper carefully |
| Forgot to disconnect the battery before working with electrical equipment | Short circuit, blown fuse | Always remove the negative terminal when working on sensors or camera |
| Incorrect bolt loosening sequence | Bumper misalignment, difficulty in reinstallation | First the arches, then the bottom of the bumper, lastly the mounts under the license plate |
A critical nuance for versions with a rear view camera: if you damage the camera cable when removing the bumper, replacing it will cost 8–12 thousand rubles (depending on the camera model). Therefore, disconnect the connector only after the bumper has been completely freed from the clips!
How to remove a bumper with parking sensors: nuances
If your Nissan Qashqai J10 equipped parking sensors, their dismantling requires special care. The sensors are attached to the bumper with latches and connected to the control unit via a wiring harness. Here's how to remove them correctly:
- Mark the location of the sensors marker on the bumper - this will help install them back without distortions.
- Carefully pry the sensor from the back of the bumper with a flat screwdriver (it should come out with a characteristic click).
- Disconnect the connector by pressing the latch. Don't pull the wires!
- If the sensor is stuck to the bumper (often happens after long use), spray it
WD-40and wait 5-10 minutes.
When reinstalling sensors:
- 🔧 Check the integrity of the o-rings - if they are torn, the sensors will not work properly.
- 🔧 Do not over-tighten the sensors - this may cause them to break.
- 🔧 After installation, check the operation of the parking sensors by placing your hand near each sensor (it should beep).
What should I do if the parking sensor does not work after installation?
If the sensor does not respond to obstacles, check:
1. **Connection polarity** - mixed up “+” and “-” will lead to inoperability.
2. **Wiring integrity** - often the wires rub against the body.
3. **Cleanliness of the sensor** - dirt or snow on the surface blocks the signal.
If the sensor still does not work, it may be faulty (resistance of a working sensor: ~200–300 Ohms).
Reinstalling the bumper: tips
Putting the bumper back on is often more difficult than removing it. Main rule: start with clips, not bolts. Here is a step-by-step algorithm:
- Connect all connectors (parking sensors, camera, light wiring).
- Place the bumper onto the clips, starting from the top corners. Make sure it sits straight, without distortion.
- Tighten the bolts in the reverse order of removal: first under the license plate, then on the sides, and lastly in the arches.
- Check the gaps between the bumper and the body - they should be the same on both sides (norm: 3–5 mm).
If the bumper does not fit into place:
- 🔧 Check if wires or connectors are in the way.
- 🔧 Make sure all clips are in place and not deformed.
- 🔧 If the bumper is skewed, loosen the bolts and adjust the position.
After installing the bumper, be sure to check the operation of all electrical components: brake lights, fog lights, parking sensors and camera. If something doesn't work, most likely you forgot to connect the connector or damaged the wiring.
Frequently asked questions about removing the Qashqai J10 bumper
How many mounting clips are there on the rear bumper of the Qashqai J10 restyling?
On the restyled version (2014–2021) usually 6–8 clips, depending on the configuration. Basic versions have 6 clips, and versions with parking sensors and a camera have 8 (additional clips secure the wiring harness).
Is it possible to remove the bumper without a pit or lift?
Yes, but it's less convenient. You will have to lie under the car to remove the bottom bolts. An alternative is to jack up the car and install jack stands. The main thing is to provide yourself with enough room to maneuver.
What kind of socket wrench is needed for the bumper bolts?
All rear bumper mounting bolts on Qashqai J10 have the size 10 mm. It is recommended to use a socket wrench with an extension for convenience.
What to do if the clip breaks?
A broken clip can be replaced with a new one (original article number: 77110-4M000). If you don't have a replacement at hand, temporarily fix the bumper with a plastic clamp, but don't leave it like that for too long - this can lead to play.
Do I need to remove the headlights when removing the rear bumper?
No, the taillights are on Qashqai J10 do not interfere with removing the bumper. Their dismantling is required only if you plan to replace lamps or repair the headlights themselves.
Conclusion: when to contact the service
Removing the rear bumper Nissan Qashqai J10 restyling is a feasible task even for a beginner, if you follow the instructions and take your time. However, there are cases when it is better to trust the professionals:
- 🔧 If the bumper is damaged in an accident and deformed, it may “drive” during installation, which will require straightening.
- 🔧 If you are not confident in your abilities when working with electrical equipment (especially if you have a version with a camera and parking sensors).
- 🔧 If the clips or fastenings are broken and need to be replaced with partial disassembly of the body kit.
In other cases, independent dismantling will save you 2–4 thousand rubles (that’s what the services charge for this work). The main thing is to remember to be careful and prepared!