Removing the rear bumper Nissan Almera G15 (2013–2022) is a task that owners face when repairing after an accident, replacing headlights, parking sensors, or treating the body against corrosion. Unlike its European counterparts, the bumper here is mounted in a combination: with latches, bolts and hidden pistons, which requires care. Errors during removal can lead to broken clips, damaged wiring, or even cracks in the bumper itself.

This article contains a step-by-step algorithm taking into account hidden fastenings, which are often missed in general instructions. We will analyze the tools, the sequence of actions for different modifications (1.6 MT/AT And 1.5 dCi), and also give advice on reassembly. Particular attention is paid problem areas: fastenings under the license plate and pistons near the wheel arches, which break in 70% of cases due to careless dismantling.

Preparation: tools and conditions

Before starting work, make sure you have everything you need. The absence of even one tool can delay the process for hours. For example, without plastic clip remover you risk breaking the latches, and without Torx T20 — do not unscrew the bolts securing the number plate illumination.

  • 🔧 Head set: 10 mm, 12 mm (for bolts under the bumper)
  • 🔩 Screwdrivers: Phillips PH2, flat (for prying off clips)
  • 🔧 Torx: T20 And T25 (for parking sensors and lighting)
  • 🧲 Plastic clip remover (or a wide screwdriver wrapped in electrical tape)
  • 🔦 Flashlight or portable lamp (lighting under the bumper is critical!)
  • 🧴 Silicone grease (for treating rubber seals before assembly)

Work for flat surface (garage, overpass) and in good lighting. If the car is on the ground, use a jack and stops - access to the lower bolts without lifting is extremely inconvenient. The air temperature should be higher +5°C: in the cold, the plastic becomes brittle, and the clips break even with careful removal.

⚠️ Attention: If on your Almera G15 installed parking sensors, before removing the bumper, disconnect them via the fuse F37 (10A) in the salon block. Otherwise, when disconnecting the wiring, an error may occur C1A10 (sensor malfunction), which will then have to be reset using a diagnostic scanner.
📊 Have you already removed the bumper on the Nissan Almera G15?
  • Yes, I did it myself
  • No, but I have experience on other machines
  • No, this is my first time
  • I plan to do it soon

Removing the license plate and lights

Let's start with the most visible element - the license plate. Here lies the first trap: many try to unscrew the sign mounting bolts without first removing plastic cover underneath it. This leads to breakage of the clasp latches.

  1. Open the trunk and find the two plastic trim clips under the number (they are located on the sides). Pry them off with a flat-head screwdriver, pre-wrapped with electrical tape, so as not to scratch the paint.

  2. Remove the cover by pulling it towards you. Underneath you will see four bolts Torx T20affixing the sign.

  3. Unscrew the bolts and remove the license plate. There are two bolts hidden underneath 10 mmholding the bumper - we don’t touch them yet.

Now let's move on to the number plate illumination. It is important here not to mix up the wires: on Almera G15 connector is used 2-pin with polarity. If you plan to disconnect the chip, remember or take a photo location of the wires (usually black - ground, red/yellow - plus).

Turn off the ignition and remove the key|Take a photo of the location of the wires|Use an insulated screwdriver|Do not pull the wires - only the connector-->

Removing the side parts of the bumper

The side sections of the bumper are mounted on caps (clips) and one bolt 10 mm on each side. The main mistake beginners make is trying to pull off the bumper from the side without unscrewing the bolt. This leads to breakage of the clips and deformation of the plastic.

Algorithm of actions:

  1. Open the front door and find the bolt 10 mm at the bottom of the arch (it is hidden under a plastic cap). Unscrew it.

  2. Pry up the plastic trim on the wheel arch (it is secured with 3 clips). Remove it to gain access to the two bumper rivets.

  3. Carefully pull out the pistons with a puller. If the clip breaks, don't panic - it can be replaced with a new one (part number Nissan 08915-JA00A).

  4. Repeat the procedure on the other side.

After removing the side mounts, the bumper will only be held in place by the central bolts and latches under the headlights. Don't try to pull it towards you - you need to release the bottom part first.

⚠️ Attention: On machines with rear fog lights (optional B92) an additional wiring harness is laid under the bumper. Do not pull it sharply - first disconnect the connector from the headlight (it is located on the left under the bumper, next to the muffler).

Unscrewing the lower and upper fasteners

Now let's move on to the bottom of the bumper. There are three bolts waiting for you here 10 mm and two plastic clips. Bolts tend to rust, so treat them before removing them. WD-40 or similar lubricant.

  • 🔧 Two bolts are located on the sides, next to the muffler (you can see them if you lie under the car).
  • 🔧 The third bolt is in the center, under the license plate (we saw it earlier).
  • 🔧 Two clips are located at the edges of the lower edge of the bumper. They need to be carefully pulled out with a puller.

The upper part of the bumper is attached to the body with four latches, which are located under the rear headlights. To release them:

  1. Remove the plastic trunk trims (they are attached to two clips on each side).

  2. Pry the bumper in the area of the headlights and pull it towards you, while pressing the latches.

Critical point: on cars 2018+, the latches under the headlights are reinforced with metal inserts. If the bumper does not budge, do not force it - check that all the bolts are unscrewed.

Mounting type Quantity Tool Typical problems
Bolts 10 mm 5 pcs. Head 10 mm + ratchet Rust, licked edges
Bolts Torx T20 4 pcs. (under number) Bit Torx T20 Jamming due to dirt
Pistons (clips) 8–10 pcs. Plastic puller They break if removed carelessly
Latch under headlights 4 pcs. Flat head screwdriver Requires simultaneous pressing

Disconnecting Wiring and Sensors

If your Almera G15 equipped parking sensors or rear view camera, before completely removing the bumper, you must disconnect the connectors. At this stage, many people make the mistake of pulling on wires instead of connectors, which leads to broken contacts.

Procedure:

  1. Locate the wiring harness coming from the parking sensors (it's usually black). The connector is located on the inside of the bumper, closer to the right fender.

  2. Press the connector latch and carefully disconnect it. Don't pull the wires!

  3. If there is a rear view camera, its connector is located under the left headlight. It is white and has an additional rubber plug.

On machines with LED-illuminated numbers (optional H11) the connector is located separately. It can be recognized by the orange wire (plus) and black (ground). After disconnecting all connectors, the bumper should be freely removable.

💡

If the connector does not come off, do not use force. Treat it with silicone lubricant and wait 5-10 minutes - this will help loosen the hold.

Removing the bumper and checking the fasteners

When all the fasteners are released, carefully pull the bumper towards you, starting from one of the corners. Movements should be smooth, without jerking. If the bumper is “bitten”, check:

  • 🔹 Are all the bolts unscrewed (especially the lower central one).
  • 🔹 Did you forget to disconnect the sensor connectors?
  • 🔹 Are there any additional clips (on machines with package SVE there may be more).

After removal, inspect the bumper for cracks and the condition of the fasteners:

  • 🔧 Replace broken clips with new ones (see the table below for article numbers).
  • 🔧 Clean and treat rusty bolts WD-40.
  • 🔧 Check the rubber seals - if they are cracked, replace them.
Detail Article Quantity per car Note
Bumper mounting clip Nissan 08915-JA00A 10–12 pcs. Suitable for all mounts
Bolt M6x20 (bottom mount) Nissan 08905-1060A 5 pcs. It's better to take extra
Sealing rubber Nissan 80310-4M000 2 pcs. (under the headlights) Changes when cracked
💡

If the bumper is removed for painting, be sure to mark the clips and bolts to their installation locations - this will speed up assembly and prevent errors.

Reassembly: nuances and tips

Installing the bumper is done in reverse order, but there are several critical moments:

  1. Before installation, clean all fastening areas from dirt and rust. Use wire brush and anti-corrosion treatment.

  2. Place the bumper on the latches under the headlights until it clicks. If the latch does not lock, do not press harder - check if the wiring is in the way.

  3. Tighten the bolts in the following order: first the top ones (under the headlights), then the side ones, and only then the bottom ones. This will prevent skewing.

  4. After installation, check the operation of all sensors and lighting. If the parking sensors do not work, check the fuse F37 and connectors.

Pay special attention adjusting gaps. There should be a uniform gap between the bumper and the body 3–5 mm. If the bumper is crooked, loosen the side bolts and adjust the position.

⚠️ Attention: On machines with system Around View Monitor (all-round view) After removing the bumper, camera calibration may be required. If a message appears on the screen "Check Camera", contact the service - self-calibration without a scanner is impossible.
What should I do if the bumper squeaks after assembly?

Creaking usually occurs due to improper installation of clips or lack of rubber seals. Disassemble the bumper again, check:

1. Are all the clips in place (especially under the headlights).

2. Are the sensor wires pinched between the bumper and the body?

3. Treat the contact areas between the bumper and the body with silicone lubricant (for example, Liqui Moly Silicon-Fett).

If the squeak remains, check the fastening under the license plate - they often forget to install a gasket there.

FAQ: Frequently asked questions about bumper removal

Is it possible to remove the bumper Almera G15 without a hole or overpass?

Technically yes, but it is extremely inconvenient. Without lifting the car, you will not be able to properly unscrew the bottom bolts and risk breaking the clips. If there is no hole, use a jack and stops, lifting the car on each side one by one.

How many clips break on average the first time you remove them?

Service statistics show that the first time you dismantle it yourself, it breaks down. 2–3 clips out of 10. To minimize risks, use a plastic puller and take your time. Clips for Almera G15 They are inexpensive (about 50–100 rubles apiece), but their absence will lead to rattling of the bumper.

Do I need to disconnect the battery before removing the bumper?

A must if you plan to work with parking sensors or lighting wiring. Even when the ignition is turned off, voltage may remain in the circuits, which will lead to a short circuit. Disconnect the negative terminal of the battery while working.

How to remove the bumper if all the clips are broken?

In this case, the bumper will only be held on by bolts and latches under the headlights. Carefully pry it around the perimeter with a flat-head screwdriver, starting from the corners. The main thing is to take your time and not apply excessive force to the plastic. After removal, replace all clips with new ones.

Is it possible to drive without a rear bumper?

Technically possible, but not advisable. The bumper protects the body from dirt and stones, and also serves as a mount for parking sensors. Without it, the risk of rear body corrosion increases. If the bumper is removed for repair, cover the exposed areas with masking tape.