How to properly remove the rear seats on a Nissan Almera G15: instructions with nuances

Removing the rear seats Nissan Almera G15 - a task that owners face when cleaning the interior, repairing electronics or installing additional equipment. At first glance, the process seems simple, but there are pitfalls here: from hidden fasteners to the risk of damaging the skin. In this article we will look at step by step instructions taking into account all the nuances of the model G15, including differences between trim levels and model years.

It is important to understand that the design of the rear sofa is Almera G15 different from previous generations (for example, N16). It uses plastic latches instead of metal hooks, and access to the fasteners can be difficult due to the nature of the casing. If you plan to remove the seats for subwoofer installation, heating repair or deep dry cleaning — these instructions will help you avoid common mistakes.

Preparing for dismantling: tools and safety precautions

Before you get started, make sure you have everything you need. To remove the rear seats Nissan Almera G15 No specialized tools are required, but some devices will greatly facilitate the process:

• 🔧 Flat head screwdriver (for prying off plastic clips)
• 🔨 10 or 12 mm socket wrench (for mounting bolts, if any)
• 🧤 Fabric gloves (so as not to scratch the casing)
• 📸 Smartphone for photography (fix the location of the clips and wiring)

Pay special attention electrical connections. Available with heated seats or seat belts with sensors There are wiring harnesses running under the sofa. On models 2019–2022, the heating connector is located under the center of the seat and is secured with an additional latch — it is easy to break if dismantled carelessly.

⚠️ Attention: If your Almera G15 equipped with a system ISOFIX, before removing the seats, check whether the child seat anchors are blocking access to the latches. On some copies, this will require you to first remove the brackets. ISOFIX.

Step 1: Removing the rear seat cushion

Start with the easiest part - the cushion (bottom) of the back sofa. B Nissan Almera G15 it is attached to the body using two plastic latches front and metal hooks behind. Algorithm of actions:

1. Open the rear doors and lower the head restraints all the way.
2. Kneel in front of the seat and pull up the cushion sharply up from the front seats. The latches should pop out with a characteristic click.
3. After releasing the front anchors, slide the pillow back to remove it from the hooks.

If the latches do not budge, do not use excessive force - most likely they are stuck due to accumulated dirt. In this case, carefully pry them out with a flat-head screwdriver, after wrapping it with electrical tape so as not to scratch the plastic.

Step 2: Removing the rear seat back

The backrest is attached more difficult than the pillow. B Almera G15 it is fixed four bolts (two on each side) and central latch below. The bolts are hidden under plastic plugs that need to be removed:

• 🔍 Find the plugs in the lower corners of the back (they look like small round or square hatches).
• 🔧 Pry them off with a screwdriver and remove them. Below them you will see socket bolts.
• 🔩 Unscrew the bolts, but not all the way - loosen them first so that the back does not fall sharply.

After removing the bolts, pull the backrest up and a little on yourself. It should come out of the grooves. Be careful: there may be seat belt sensor wires (in configurations with SRS). They need to be disconnected by first removing the negative terminal from the battery.

⚠️ Attention: On models with folding backrest (optional 60:40) you must first unlock the folding mechanism. To do this, pull the lever under the seat cushion, as you would when folding it to carry cargo.

What to do if the bolts are soured?

If the bolts will not come off due to corrosion, use a penetrating lubricant (such as WD-40). Apply it 10-15 minutes before work. Do not use excessive force - stripped threads will make reassembly more difficult.

Features of fastenings in different configurations

Rear seat design Nissan Almera G15 varies depending on the configuration and year of manufacture. Below is a table with the key differences:

Equipment/Year	Pillow mounting type	Backrest fastening	Additional nuances
Base (2018–2020)	2 plastic latches + 2 hooks	4 bolts (T30 Torx)	No heating, simple design
Comfort (2019–2021)	2 latches + 2 hooks + heating lock	4 bolts (T30 Torx) + heating connector	Heating wires glued to foam rubber
Tekna (2020–2023)	2 latches + 2 hooks + occupancy sensor	4 bolts (10mm hex) + 2 connectors	System ISOFIX with additional staples

For example, in Tekna hidden under the back trim rear seat occupancy sensor, which is associated with the system SRS. If disconnected incorrectly, an error light may appear on the dashboard. If you are not confident in your skills, it is better to contact the service.

Common mistakes and how to avoid them

Even experienced car owners make mistakes when removing rear seats. Here are the most common ones and how to prevent them:

• 🔧 Broken threads of bolts - occurs due to the use of an inappropriate key. Always check the size before unscrewing.
• 🔌 Broken heating wires — pull the connectors only by the body, not by the wires. If the contacts are oxidized, clean them before disconnecting.
• 🧹 Lost clips — plastic latches are easily lost. Place them in a separate bag immediately after removal.

Another common problem is incorrect backrest installation after dismantling. If the bolts are not tightened completely, the back will play, which will lead to squeaks. Check the reliability of the fastening by rocking the seat after assembly.

⚠️ Attention: On models with side airbags (optional Side Airbag) squibs are installed in the back of the rear seat. It is strictly forbidden to drop the backrest or subject it to impacts - this may cause the airbag to deploy.

Cleaning and maintenance after dismantling

When the seats are removed, you have a unique opportunity to spend deep interior cleaning and prevention of mechanisms. Here's what to do:

• 🧽 Cleaning the foam - Vacuum it and treat it with antibacterial spray.
• 🔧 Mechanism lubrication — Apply silicone grease to the backrest guides and latches.
• 🔌 Wiring check — inspect the harnesses for frayed insulation.

If you removed the seats for installation subwoofer or amplifier, make sure that the new wires are not pinched during reassembly. Use corrugated tubing to protect cables from chafing.

FAQ: Frequently asked questions about removing rear seats

Do I need to disconnect the battery before use?

Yes, if yours Almera G15 equipped with heated seats or seat belt sensors. This will prevent short circuits when disconnecting the connectors. In basic configurations without electronics, switching off is not necessary.

Is it possible to remove only part of the backrest (for example, 60% or 40%)?

Available with folding backrest 60:40 Only one section can be dismantled. To do this, unscrew the bolts securing the required part and disconnect it from the central lock. The rest of the backrest can be left untouched.

How can you tell if the airbag latches are stuck?

If the pillow does not give way when you jerk upward, try pressing down on it to relieve the tension on the clips. If this doesn't help, use a screwdriver, but be careful - the plastic is fragile.

What should I do if the back is loose after assembly?

Most likely, the bolts are not tightened completely or the threads are broken. Check that the fastening is secure and use thread lock if necessary (e.g. Loctite).

Can the seat upholstery be washed in the washing machine?

No, this will lead to deformation of the fabric and foam rubber. For cleaning use steam generator or special shampoos for car dealerships with a soft brush.