How to properly remove the rear seat on a Nissan Juke: instructions with nuances

Removing the rear seat Nissan Juke - a task that owners face when stowing luggage, cleaning the interior or repairing electronics. Despite its apparent simplicity, the process has its pitfalls: from hidden latches to the risk of damaging the skin. In this article we will analyze step-by-step algorithm for all model generations (2010–2026), including unique latches on restyled versions after 2019.

Difference Juke compared to other crossovers - compact interior and non-standard mounting design. For example, in basic versions the seat is secured with two metal hooks in the front and plastic latches in the back, and power connectors are added in heated versions. If you are planning complete dismantling (along with the cushion and backrest), you will need a Torx T20 wrench - this is often overlooked.

Before you begin, please note: on vehicles with the system NissanConnect Antennas or control units may be located under the seat. Disabling them accidentally will result in media failure. Also in 2020+ models, a seat belt sensor is hidden under the airbag - damage to it will disable the passenger unbelt alarm.

Preparation: Tools and Safety Precautions

To work you will need:

• 🔧 Flathead screwdriver (for prying up plastic clips)
• 🔩 Torx key T20 (for backrest fastenings in versions with ISOFIX)
• 🧲 Magnetic holder (so as not to lose small bolts)
• 🧴 Silicone grease (for treating latches before reinstallation)

Required disconnect the battery 10 minutes before starting work - this will relieve the voltage in the airbag squibs (if your equipment has them). B Juke 2014-2017 The wiring harness to the fuel gauge runs under the rear seat - it should not be kinked or pulled.

⚠️ Attention: On models with a panoramic roof (Juke Nismo and luxury versions) there may be an air conditioning drain hose under the seat. If you hit it, a puddle of condensation will appear in the cabin.

Step 1: Removing the Seat Cushion

Start at the front of the pillow. Pry the plastic trim over the latches (located at the feet of the front passengers) and pull it up. Under it you will see two metal hooks - you need them at the same time move forward by pressing the latches. B Juke 2019+, the hooks may be hidden under the felt pad - you will have to carefully cut it off with a knife.

The back of the pillow is secured with plastic latches. To release them:

1. Raise the pillow by the front edge by 10–15 cm.
2. Pull it towards you with a sharp movement - the latches should pop out of the grooves.
3. If the seat does not give way, check to see if the seat belt is caught in the frame.

In versions with heated seats, there will be a power socket under the cushion. It cannot be pulled out by the wires - only by the plastic case! Connector color may vary: Juke until 2016 it was black, in the new ones it is gray with an orange mark.

Step 2: Removing the seat back

The backrest is secured with two Torx T20 bolts (in versions with ISOFIX - four). They are hidden under plastic plugs in the lower corners. To remove them:

1. Pry off the plugs with a flat head screwdriver, starting at the top edge.
2. Unscrew the bolts while holding the backrest - it may fall forward.
3. If the bolts do not budge, apply WD-40 and wait 5 minutes.

In models with separate backrest (60/40) each part is removed separately. At the same time, the left side (60%) has an additional lock in the form of a metal bracket - it must be bent manually. On restyled Juke (2019+) the backrest can be equipped with air shock absorbers - they cannot be dropped or twisted.

Generation Juke	Backrest mounting type	Features
2010–2014 (J10)	2 Torx T20 bolts	The plugs are fragile and break when pressed hard
2014–2019 (J11)	4 bolts (with ISOFIX)	Additional bracket on the left side of the backrest
2019–2026 (J15)	2 bolts + air shock absorbers	Heating connector with orange mark

⚠️ Attention: In Juke Nismo RS the backrest can be glued to the body with sealant. An attempt to rip it off will damage the casing. In this case, use a hair dryer to soften the glue.

Step 3: Disconnect Electronics (If Equipped)

If your Juke equipped with heated seats, passenger weight sensors or multimedia connectors, they must be properly disconnected. Connector location:

• 🔌 Heating: under the pillow, left and right (black or gray pads).
• 📡 Antenna NissanConnect: under the back, in the center (blue connector).
• ⚖️ Weight sensor: under the pillow, closer to the right side (yellow connector).

To disconnect a connector:

1. Press down on the plastic tab (usually orange or green).
2. Pull the body, not the wires!
3. Wrap the connectors with electrical tape to prevent short circuits.

Cleaning and maintenance after removal

When the seat is removed, you can deep cleaning or repair. For example, in Juke Often the drainage holes under the seat become clogged - this leads to the accumulation of moisture and corrosion of the body. To clean them:

1. Remove debris using a vacuum cleaner with a narrow attachment.
2. Flush the holes with pressurized water (for example, from a carburetor cleaner).
3. Treat with anti-corrosion compound (Molykote or CRC Lanox).

If you removed the seat for tuning (e.g. subwoofer installations), please note:

• 🎵 B Juke limited space for acoustics - maximum box depth 15 cm.
• 🔊 It is better to attach the speakers to a metal seat frame rather than to plastic.
• 🔌 Lay the power wires along the standard wiring so as not to damage them during reinstallation.

How to check the passenger weight sensor?

After reinstalling the seat, turn on the ignition and look at the airbag indicator on the dashboard. If it flashes 5 times, the sensor is faulty or not connected correctly. To reset the error, you may need a diagnostic scanner (for example, Launch X431).

Reinstallation: errors and solutions

During assembly, 80% of problems arise from incorrect fixation of latches. For example, if the front hooks do not engage fully, the seat will wobble when moving. To avoid this:

1. Make sure that the hooks are fully seated in the grooves (you should hear a click).
2. Check to see if any debris or wires have gotten under the latches.
3. After installation, pull the seat up - if it does not move, the fastening is secure.

The second common mistake is twisted wires heating If after assembly one side of the seat heats less, it means the wire is pinched or damaged. In this case:

• Remove the cushion and check the integrity of the wiring.
• Use a multimeter in continuity mode to check the resistance (normal: 1.5–2.5 ohms).
• If the wire is broken, repair it using soldering and heat shrinking.

Frequently asked questions and problems

Is it possible to remove the seat without disconnecting the battery?

Theoretically, yes, but only if your package does not include airbags or weight sensors. B Juke 2018+, even the side curtain airbags are linked to the seat electronics, so the risk of the squibs being deployed remains. If you decide not to disconnect the battery, at least remove the fuse SRS (usually F10 or F15 in the mounting block).

Why does the seat squeak after installation?

The creaking occurs due to the friction of the plastic latches on the metal frame. Solution:

1. Remove the seat and apply silicone lubricant to all contact points.
2. Check if the latches are deformed (sometimes they break during rough removal).
3. If the squeak remains, place thin rubber pads under the latches.

How to remove the seat if one latch is stuck?

Do not try to pull the seat out by force, as this will break the plastic retainer. Instead:

1. Treat the latch with penetrating lubricant (PB Blaster or Liqui Moly).
2. Use a flathead screwdriver to gently pry out the retainer.
3. If the latch is broken, it can be temporarily replaced with a plastic clamp or ordered a new one (part number: 26560-JM00A for Juke 2010–2019).

Where in the cabin can you hide tools if there is no trunk?

B Juke there are several hidden places:

• 🚗 Under the floor mat at the feet of the rear passengers (there is a plastic tray there).
• 🔧 In the niche behind the seat back (if it is folded).
• 📦 Under the trunk floor (there is usually a spare tire or compressor).

Do not store tools under the seat - they may damage the wiring or interfere with the latches.

Can the removed seat be washed with water?

Yes, but with reservations:

• 🚿 Use only cold water and a soft brush.
• 🧼 The detergent must be pH neutral (e.g. Autoglym Interior Shampoo).
• 🔥 Do not dry the seat in direct sunlight or with a hairdryer - this will deform the foam.

If the upholstery is leather, apply leather conditioner after washing (Leatherique or Sonax}).