Incorrect actions can lead to breakage of plastic clips or damage to decorative inserts. Fastening system in Nissan Almera G15 differs from its predecessors, and here it is important to understand the difference between dismantling the lower cushion and the upper backrest. In this article we will analyze each stage of the work so that you can safely carry out the procedure yourself.
Preparing tools and workspace
Before starting work, it is necessary to empty the luggage compartment of all foreign objects. Even a small toolbox can prevent you from freely manipulating heavy interior components. Make sure the vehicle is on a level surface and the handbrake is engaged to prevent accidental movement.
You will need a minimum set, which most car enthusiasts have. The main emphasis is on hand flexibility and the presence of simple levers.
- 🔧 Thin flathead screwdriver or plastic card for prying latches
- 🔨 Rubber mallet or wooden block (for gentle tapping)
- 💡 Flashlight for inspecting hidden fasteners under the sofa
Pay special attention to the condition of the floor in the trunk. If there is a rug there, it is better to remove it immediately so as not to stain or lose small parts. Plastic clips on Nissan Almera They are quite fragile at low temperatures, so in the cold season it is better to pre-heat the interior. This will make the plastic more flexible and reduce the risk of it breaking when removed.
⚠️ Caution: Do not use sharp metal tools to pry open panels without protection, as you may leave deep scratches on the decorative trims or scratch the trunk floor.
Removing the lower seat cushion
The lower part of the rear sofa on Nissan Almera G15 It is not secured with bolts, but with a system of hooks and stops. This makes removal easier but requires proper pulling technique. Sit in the front seat and lean toward the back to find the mounting points.
The front edge of the cushion hooks onto the hooks on the body, and the back simply rests on the floor. You need to lift the front edge of the pillow up. Do this with a sharp but controlled movement so that the hooks come out of the grooves.
- 🖐️ Grab the bottom of the pillow with both hands by the front edge
- 🚀 With a powerful upward jerk, release the front latches
- 🎒 Carefully remove the pillow from the passenger compartment through the doorway
If the cushion fits too tightly, you can use a plastic card or a soft-tip screwdriver to lightly press the hook. However don't put in too much effort, otherwise the plastic base of the pillow may crack. After removing the cushion, you will have access to the trunk floor and the upper backrest mounts.
If the cushion does not budge, check whether the hooks are blocked by foreign objects stuck in the mounting groove on the floor.
⚠️ Caution: When removing the airbag, be careful not to snag the heated seat wiring or seat belt sensors that may be located near the mounting location.
Removing the top (back) of the sofa
After removing the pillow, access to the backrest locking mechanism opens. On Nissan Almera the backrest is fixed at the top with two metal latches. To release them, you need to pull the special straps or tabs located under the upper edge of the upholstery.
Sometimes access to these fasteners is difficult if they are hidden under decorative plugs or a casing. You need to carefully peel back the top of the upholstery to see metal hooks. Pull the strap or press the lock while simultaneously lifting the backrest up.
- 🔍 Inspect the top of the backrest for release tabs
- ⬆️ Lift the backrest vertically up, moving the hooks out of the grooves
- 🔄 Tilt the backrest forward and remove it from the interior
If the backrest does not rise, it may be blocked by the mechanism. child protection or seat belts. Check that the belts are not crossed and that the release button is not jammed. In some modifications Nissan Almera the back may be solid, while in others it may be divided into two parts (60/40), which requires removing each part separately.
☑️ Removing the back of the sofa
Access to technical units and tank
The main reason for removing seats is to get to the fuel filler neck, pump or suspension components. After dismantling all the parts, you will see a metal floor and plastic covers. Fuel pump usually located under a hatch in the floor, closed with an additional cover.
To access the pump, you need to unscrew the mounting bolts of the hatch cover. It is important to be careful here as there is an electrical connector and hoses under the cover.
- 🔌 Disconnect the fuel pump electrical connector
- 🔧 Unscrew the fixing bolts or nuts of the hatch cover
- ⛽ Carefully remove the pump, observing the position of the float
If you need to remove the rear suspension, the shock absorbers and springs are completely accessible. However, be careful with ABS sensor wiring, which can pass in close proximity to the fastenings. Do not cut or pinch wires when working in confined spaces.
Hidden nuances of access to the tank
On some versions of the Almera G15, the fuel pump hatch may be hidden under a soundproofing mat, which will have to be carefully peeled off or cut off if it interferes with dismantling.
⚠️ Attention: When working with the fuel system, make sure that there is no excessive pressure in the tank, and work in a ventilated area, excluding the presence of open flames.
Table of fasteners and their location
For clarity, here is a table describing the main attachment points that you will encounter when disassembling the interior. Knowing these points will help avoid confusion and loss of detail.
| element | Mounting type | Quantity | Features |
|---|---|---|---|
| Bottom cushion | Hooks | 2 pcs. | Front, require lifting |
| Back (top) | Metal staples | 2-4 pcs. | Top, secured with straps |
| Pump hatch | Torx bolts | 3-5 pcs. | Accessible after removing the cushion |
| Armrest | Screws under plastic | 2 pcs. | Hidden under covers |
Always visually check for hidden fasteners before attempting any force.
Correct understanding of the type of fastening of each element is the key to successful dismantling without damage to the interior.
Putting the seats in place
The installation process is a mirror image of dismantling, but requires greater attention to clicking sounds. Install the backrest top first by inserting the hooks into the slots in the roof or rear parcel shelf. Make sure the latches click into place by pulling the backrest towards you.
Then the bottom cushion is installed. You need to align the front hooks with the grooves on the floor and sharply push down until you hear a characteristic click. Reliability check mandatory: try rocking the seat to make sure there is no play.
- 🔊 Listen to the clear clicks of fixation
- 📏 Check the symmetry of the installation in relation to the floor
- 🛡️ Make sure the seat belts are not twisted
If you removed the fuel pump door, be sure to connect the connector and screw the cap securely. Tightness The fuel system is critical to the safety and proper operation of the engine. Finally, check the operation of all mechanisms: folding the backrest, heating, adjusting the belts.
- For suspension repair
- To access the fuel pump
- For transportation of long cargo
- For interior cleaning
Frequent mistakes and tips for maintaining the salon
Many owners Nissan Almera make the mistake of trying to remove the seat without clearing the space around it. This causes the plastic to crack on sharp corners of the trunk or door openings. Always remove unnecessary items and use soft door card covers when necessary.
Another common problem is the breakdown of plastic fasteners during winter dismantling. In cold weather, plastic becomes brittle, and any sudden movement can lead to its destruction. Warming up the interior before starting work - this is not a whim, but a necessity.
- ❄️ Do not remove seats at temperatures below -10°C without warming up
- 💧 Use plastic lubricant if the latches are stuck
- 🛠️ Have spare clips in case the old ones break
Remember that The backrest fastening system on the Nissan Almera G15 requires simultaneous action on two latches for safe release. If you only pull on one, the mechanism may jam, leading to costly repairs.
⚠️ Attention: When installing, do not overtighten the pump hatch mounting bolts, as this may lead to deformation of the plastic and damage the seal of the fuel tank.
FAQ: Frequently asked questions
Do I need to disconnect the battery before removing the seats?
No, you do not need to disconnect the battery to mechanically remove the seats. However, if you plan to work on the fuel pump wiring or sensors, it is recommended that you remove the negative terminal.
How to remove the seat if the lock is stuck?
Try to slightly rock the seat in different directions while applying force to the latch. You can use WD-40 lubricant to eat away the rust if the mechanism is corroded.
Is it possible to remove only one part of the backrest (60/40)?
Yes, depending on the configuration Nissan Almera G15 the back is divided into two parts. You can remove just the smaller or larger section by unfastening the corresponding latches.
Is it difficult to remove the seat by yourself?
You can remove the bottom cushion yourself, but to remove the backrest and especially to install it back, it is better to have an assistant, since the elements can be heavy and inconvenient to manipulate alone.