Nissan Almera Classic (also known as B10 or N16 in some markets) is a popular sedan that often requires access to the trunk or fuel pump. Removing the rear seat may be necessary to replace the upholstery, repair electrical wiring, or clean the interior. In this article we will look at the process of removing the seat. step by step, taking into account the nuances of a specific model and generation.

The design of the rear sofa in Almera Classic simpler than in modern crossovers, but has its own characteristics. For example, the fasteners are hidden under plastic plugs, and in some configurations there are retractable seat beltsthat cannot be damaged. If you plan to do any electrical work (such as checking fuses under the seat), be sure to disconnect the battery 10 minutes before starting work - this will prevent a short circuit.

Unlike Nissan Qashqai or X-Trail, where seats are often secured with complex latches, in Almera Classic a system of two main mounts (front) and latches (behind). However, in cars with heated seats or side airbags, the process becomes more complicated - we will talk about this separately.

What tools will you need?

To remove the rear seat Nissan Almera Classic No professional tools are required, but some accessories will make the task much easier. Here's the full list:

  • 🔧 10 mm socket wrench (or a head with a ratchet) - for unscrewing the fastening bolts.
  • 🔨 Flat head screwdriver (medium size) - for prying off plastic plugs.
  • 🧲 Magnetic holder or tweezers - so as not to lose the bolts in the interior.
  • 🧴 Silicone grease (optional) - for processing rusted fasteners.
  • 📸 Smartphone — for photographing the location of the wires (if there is heating).

If your car has ISOFIX child seats, their fastenings may interfere with dismantling. In this case, additionally prepare 12 mm wrench for unscrewing staples. Also useful flashlight — interior lighting Almera Classic often leaves much to be desired, especially under the seats.

📊 How often do you remove the back seat in a car?
  • For repairs only
  • Frequently (for example, for transporting goods)
  • Never filmed
  • I don't know how to do this

Preparing the interior before dismantling

Before you begin removing the seat, you need to prepare the interior. This will prevent damage to the casing and loss of small parts.

Remove all items from the back seat and trunk|

Disconnect the battery (remove the negative terminal)|

Move the front seats to the full forward position|

Place cardboard or cloth on the floor (to avoid scratching the plastic)|

Take a photo of the location of the wires (if there is heating) -->

Pay special attention seat belts. B Almera Classic they are attached to the body through hinges, which can interfere with raising the seat. We recommend:

  1. Unfasten the seat belts and carefully place them on the backs of the front seats.
  2. Check if the belts are caught under the seat (sometimes they get caught in the guides).
  3. If the car has central armrest, it must be removed separately (usually it is attached to 2 bolts under the plugs).

On 2006-2012 vehicles, there may be a fuse box for the audio system or alarm located under the rear seat. If you do not plan to work with electricians, it is better not to touch these wires - accidentally disconnecting them can reset the radio settings.

Step-by-step instructions: how to remove the rear seat

The dismantling process consists of several stages. We will analyze the standard equipment Nissan Almera Classic no heated seats. If your car has additional options, please see the separate section below.

Step 1: Removing the plastic plugs

In the front part of the seat (on the side of the passengers' legs) there are two plastic plugs, under which the fastening bolts are hidden. To remove them:

  1. Pry up the plug flat screwdriver from the edge (from the door side).
  2. Gently pull up - it should come out of the grooves.
  3. Repeat the procedure for the second plug.

Be careful: plastic in Almera Classic quite fragile, especially in cars older than 10 years. If the plug does not give in, you can slightly heat it with a hairdryer (no higher than 60°C) to make the plastic more elastic.

Step 2: Unscrewing the mounting bolts

Under the plugs you will see two bolts on 10 mm. They need to be unscrewed with a socket wrench or a ratchet head. Tips:

  • 🔩 If the bolts are rusty, treat them WD-40 10–15 minutes before unscrewing.
  • 🧲 Use a magnetic holder to prevent the bolts from falling under the seat.
  • ⚠️ Do not use excessive force - the threads in the body may be weakened by corrosion.

After removing the bolts, the seat will still be held in place by the latches at the rear. Don't try to pull it towards you - you need to release the back first.

Step 3: Release the Latches

The back of the seat is fixed on two spring latches, which are located closer to the back. To release them:

  1. Raise the seat by the front edge by 10–15 cm.
  2. With a sharp movement, pull it up and slightly back (towards the trunk).
  3. The latches should come out of the grooves with a characteristic click.

If the seat does not give way, check whether the seat belts or wires are caught (in heated cars). It is also possible that the latches may become deformed - in this case they can be pryed off with a screwdriver, but carefully so as not to break them.

💡

If the seat is “jammed” and does not want to come out of its grooves, try rocking it from side to side. This often helps release the latches without additional tools.

Step 4: Completely Removing the Seat

After releasing the latches, the seat can be removed from the passenger compartment. Do this carefully:

  • 🚗 It’s better to work together - one person lifts the seat, the second takes it out through the doorway.
  • 🔌 If there is one in the car airbags in the rear seats (rare, but found in top trim levels), do not drop the seat - this may cause the squib to fire.
  • 📦 Place the seat on a soft surface (such as a blanket) to avoid scratching the upholstery.

You now have access to the fuel pump (under the right side of the seat), luggage compartment and electrical wiring. If you removed the seat for cleaning, we recommend vacuuming the space underneath it - debris and sand often accumulate there.

Features of dismantling in different configurations

Depending on the year of manufacture and equipment Nissan Almera Classic, the process for removing the seat may vary. Let's look at the main options.

Equipment/option Features of dismantling Additional tools
Basic (without heating) Two bolts at the front, latches at the back. No wires. 10 mm wrench, screwdriver
Heated seats You need to disconnect the power connector under the seat. Take pictures of the wire locations! 10mm wrench, connector tweezers
With ISOFIX Additional bracket fastening bolts (12 mm wrench). 12 mm wrench, WD-40 for rusty bolts
With side airbags It is dangerous to drop the seat! It is recommended to disconnect the battery 30 minutes before work. 10 mm wrench, diagnostic scanner (optional)

In cars 2010–2012 sometimes there are seats with adjustable backrest tilt. In this case, there may be additional cables or springs under the casing - they cannot be damaged. If you are not confident in your abilities, it is better to contact the service.

What to do if the latches are broken?

If the spring latches break during dismantling, they can be replaced with new ones (item number for Almera Classic — 77110-4M000). A temporary solution may be to secure the seat with zip ties, but this is unsafe in the event of an accident. To replace the latches, you will need to remove the trunk trim (4 10 mm bolts and clips).

Common mistakes and how to avoid them

Even experienced car owners sometimes make mistakes when removing the rear seat. Here are the most common ones and how to prevent them:

⚠️ Attention! Never pull the seat towards you without releasing the latch at the back. This can lead to deformation of the metal frame or breakage of the heating wires.
  • 🔧 Lost bolts — always put them in a separate box or magnetize them to a holder. Inside Almera Classic There are many cracks where small parts can fall through.
  • 🔌 Wiring damage — if the car is heated, do not jerk the seat sharply. Disconnect the connectors first!
  • 🚗 Scratches on plastic — place a cloth under the tools, especially when working with a screwdriver.
  • 🔩 Thread failure - Do not overtighten the bolts when reinstalling. Tightening torque: 8–10 Nm.

Another typical problem is jamming of latches due to corrosion. If the seat doesn't want to come out, don't force it. Better treat the latches penetrating lubricant (For example, Liqui Moly MoS2) and wait 20–30 minutes. As a last resort, you can carefully drill out the rivets and replace them with new ones.

💡

If the seat wobbles or squeaks after installation, check the condition of the rubber dampers under the bolts. They can be purchased separately (item no. 01534-40010) or replace with washers of suitable size.

How to put the seat back?

Reinstalling the rear seat in Nissan Almera Classic easier than dismantling, but there are nuances here too. Follow this instruction:

  1. Make sure there are no foreign objects (tools, rags) under the seat.
  2. Carefully lower the seat into place, aligning the latches with the grooves in the body.
  3. Press the back of the seat until you hear a characteristic click (this means the latches are locked).
  4. Tighten the bolts at the front, but do not immediately tighten them all the way.
  5. Check if the seat is wobbly. If everything is in order, finally tighten the bolts.

If your car has heated seats, before installation, check:

  • 🔌 Condition of the connectors - is there any oxidation or damaged contacts.
  • 📸 Correct connection (check with photos taken before dismantling).
  • 🔥 Heating performance - turn it on for 1-2 minutes and check the heating.

After installing the seat, we recommend checking the operation of the seat belts - they should extend and retract freely. If the belt is stuck, it may be caught under the seat guide.

When should you contact the service?

Although removing the rear seat Nissan Almera Classic - a relatively simple procedure, in some cases it is better to entrust it to professionals. Contact the service if:

  • 🚨 The airbag has deployed in the car, and the electrics need to be checked.
  • 🔧 The mounting bolts are broken and new threads are required.
  • 🔥 After dismantling, the seat heating or audio system stopped working.
  • 🛠️ You need to disassemble the seat to replace the foam or trim (this requires a special tool).

The cost of service for removing/installing a rear seat usually does not exceed 800–1500 rubles (for 2026). However, if the problem is electrical (for example, a short circuit after an incorrect connection), the price can rise to 3000–5000 rubles for diagnostics and repairs.

If you doubt your abilities, but want to save money, you can order visiting technician. Many auto electricians offer such services at a price of 1000 rubles per visit + cost of work.

FAQ: Frequently asked questions about removing the rear seat

Is it possible to remove the rear seat? Nissan Almera Classic without tools?

Theoretically, yes, if the bolts are not rusty and the latches are in good condition. However, without a screwdriver you will not be able to remove the plastic plugs, and without a socket wrench you will not be able to unscrew the bolts. In an emergency, you can try to turn the bolts with pliers, but this risks breaking the edges.

What should I do if the fuel pump does not work after removing the seat?

Most likely, you touched the pump power connector (it is located under the right side of the seat). Check if the chip is disconnected. The fuse could also have tripped (in the block under the hood, usually F15 at 15A). If the pump does not hum when you turn on the ignition, the problem is more serious - the wiring may be damaged.

How to remove the seat if the bolts are stuck?

Stuck bolts are a common problem in cars older than 10 years. Proceed like this:

  1. Treat the bolts WD-40 or Liqui Moly Rostloser and wait 15–20 minutes.
  2. Try to unscrew them with impact wrench (if any).
  3. If this does not help, heat the bolt with a hair dryer (no higher than 200°C) and try again.
  4. As a last resort, cut the bolt with a grinder and replace it with a new one (M6 thread).
Do I have to remove the seat back to get to the trunk?

No, in Nissan Almera Classic The rear seat backrest reclines separately (if provided for in the package). The folding lever is usually located in the trunk, next to the backrest hinges. If there is no lever, the backrest is not removable, and to access the trunk you will have to remove the entire seat.

Can the removed seat be washed with water?

You can, but with caution:

  • Use soft brush And car shampoo (For example, Kärcher).
  • Do not direct high-pressure water jets at the seams of the sheathing - this may damage the foam.
  • After washing, dry the seat thoroughly in the sun or with a hairdryer (at least 2-3 hours).
  • If the seat is heated, avoid getting water on the heating elements.